Enviro EF2 Dial-a-fire has no effect on the fire, Potentiometer Readings, Stove will not shut off

Page 30

Troubleshooting

8. The dial-a-fire has no effect on the fire.

wMake sure all connections to the timer control module are secure.

wPerform a resistance test to the dial-a-fire potentiometer by placing the two (2) test leads from a multimeter into the leads of the potentiometer. The potentiometer should have a range of 68KΩ to approximately 850 KΩ (± 10%).

Potentiometer Readings:

Full counter-clockwise (switched off) = open circuit, overload or infinite resistance Low fire ...............................800 KΩ to 900 KΩ

High fire ..............................68 KΩ to 82 KΩ

If the range is not close or does not vary then replace the potentiometer.

9. The stove will not shut off.

wMake sure the AUTO/MANUAL switch is in the AUTO position.

wCheck the connections to the 120°F (49°C) temperature sensor and AUTO/MANUAL switch against the wiring diagram.

wCheck the 120°F (49°C) temperature sensor by removing one of the brown wires from the sensor. The unit should shut down right away as long as the switch is in the AUTO position. If the stove shuts down, replace the 120°F (49°C) sensor. If the stove does not shut down, test the switch.

wTo test the switch, the stove must be cold. With one of the brown wires removed from the 120°F (49°C) temperature sensor, remove the grey wire from the switch, the stove should shut down. If this is the result then replace the AUTO/MANUAL switch.

wIf the stove still does not shut off, replace the wiring harness.

10. The stove keeps going out

If the stove goes out and leaves fresh unburned pellets or cigarette-like ashes in the burn pot liner, the fire is going out before the stove shuts off.

wCheck to see that the Slider / Damper is in the correct position.

wTurn the Dial-a-Fire up slightly (poor quality pellets will require slightly higher settings).

If the stove goes out and there are partially burned pellets left in the burn pot liner, the stove has shut down due to a lack of air, exhaust temperature, or power failure.

wAdjust the Slider / Damper.

wCheck to see if the stove needs a more complete cleaning.

wDid the power go out?

wContact your local Dealer for service.

wTurn the Dial-a-Fire up slightly (poor quality pellets will require slightly higher settings).

If the stove goes out and there are no pellets in the liner, the auger is stopping.

wSee “The auger motor will not function normally” and “The exhaust blower will not function normally.”

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents EF2 Table of Contents Introduction I. Pellet StandardsStore pellets at least 36 1 m away from the pellet stove USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Reasons WHY the Unit Overheated Operating InstructionsSpecial Notes Special Notes Burn POT and Liner 2-3 days Routine Cleaning and MaintenanceTools Required to Clean Unit Inside Firebox 2-3 daysNot Place Unburned or RAW Pellet Fuel in ASH PAN Freestanding ASH PANFireplace Insert and BUILT-IN Heater ASH PAN Post Season CLEAN-UP Cleaning Plated SurfacesBrick Panel Installation Screws to take out to remove stove from palletDimensions of EF2 Freestanding Minimum Alcove width Inches 91 cm Minimum Alcove height Or from the outside of the pedestal for the FPI or BIH EF2 Built-In Heater recommended FramingArea Under Sundeck Exhaust Freestanding Fireplace Insert Built-In HeaterFresh AIR Intake Fresh Air Intake Unit on it Locate the center of the exhaust Is the recommended installation set up Inside Vertical Installation Install the hearth pad Freestanding hearth mount installation overview Elbow to the exhaust pipe This unit includes a 3 75 mm pedestal Corner Brackets Removal Side surround panel swings forwardTroubleshooting Stove will not startStove will not light Stove will not function in the Auto mode when hot Exhaust motor will not function normallyConvection blower will not function normally Auger motor will not function normally Stove will not shut off Dial-a-fire has no effect on the firePotentiometer Readings Stove keeps going outWiring Diagram Parts List Fireplace Insert Stove Top Parts List Parts List Options ComponentsDPartsiagram Parts Diagram Steel Warranty To the DealerWarranty Installation Data Sheet Name of Owner Address

EF2 specifications

The Enviro EF2 is a cutting-edge electric vehicle specifically designed for urban environments, combining eco-friendliness with advanced technology. This vehicle stands out in the burgeoning electric vehicle market due to its unique blend of functionality, efficiency, and sustainability.

One of the main features of the Enviro EF2 is its remarkable range. With a fully charged battery, it can travel up to 300 miles, making it ideal for both daily commutes and longer journeys. The vehicle is equipped with a high-capacity lithium-ion battery pack, which not only extends its range but also ensures quick charging times. Thanks to fast-charging capabilities, the battery can be recharged to 80% in just 30 minutes, allowing drivers to minimize downtime and maximize productivity.

The Enviro EF2's performance is further enhanced by its advanced electric drive system. This system delivers impressive torque and acceleration while maintaining a quiet and smooth driving experience. The vehicle boasts a top speed of 120 mph, enabling drivers to merge seamlessly into highway traffic while enjoying the benefits of electric driving.

In terms of design, the Enviro EF2 embodies modern aesthetics with a sleek and aerodynamic exterior. The interior is equally impressive, featuring a spacious cabin lined with sustainable materials that provide both comfort and style. Smart seating configurations make the vehicle adaptable for families or cargo, with ample storage solutions to accommodate various needs.

Technologies incorporated into the Enviro EF2 include state-of-the-art infotainment systems, offering seamless connectivity through smartphone integration. The vehicle also includes advanced driver-assistance systems, enhancing safety through features such as adaptive cruise control, lane-keeping assist, and automatic emergency braking. These technologies work together to create a more secure driving experience.

The Enviro EF2 emphasizes sustainability beyond just its electric powertrain. The manufacturing process incorporates eco-friendly practices, and the materials used in production are chosen for their minimal environmental impact. This makes the vehicle a responsible choice for environmentally-conscious consumers.

In conclusion, the Enviro EF2 represents a significant advancement in electric vehicle technology. With its impressive range, rapid charging capabilities, performance features, and sustainable design, it meets the evolving needs of urban drivers, making it a compelling choice in the electric vehicle landscape. The Enviro EF2 is not just a vehicle; it is a forward-thinking solution for a cleaner, greener future.
Top Page Image Contents