Enviro EF-119 owner manual Installation, Screws to take out to remove stove from pallet

Page 11

Installation

DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE:

1. Check clearances to combustibles.

2. Do not obtain combustion air from an attic, garage or any unventilated space. Combustion air may be obtained from a ventilated crawlspace.

3. Do not install the stove in a bedroom.

4. You can vent the stove through an exterior wall behind the unit or connect it to an existing masonry or metal chimney (must be lined if the chimney is over 6” (15 cm) diameter, or over 28 inches² (180 cm²) cross sectional area). An interior vent can be used with approved pipe passing through the ceiling and roof.

5. Locate the stove in a large and open room that is centrally located in the house. This will optimize heat circulation.

6. The power cord is 8 feet (2.43 m) long and may require a grounded extension cord to reach the nearest electrical outlet.

REMOVING PELLET STOVE FROM PALLET:

To remove your new stove from its pallet, open the left and right side panels. To open the side panels remove the ash pan cover from the magnets located below the door. Remove the two (2) T-20 screws located at the bottom corners of the left and right side panels. Remove the two (2) T-20 screws located between the hopper side rails and the side panels at the front edge of the side panel.

There are two (2) wood screws that are holding the bottom of the stove to the pallet. Remove the screws. Close the side panels. See “PEDESTAL INSTALLATION” to install the pedestal.

Fireplace Insert Model

Freestanding

 

Remove the screw here

Figure 5: Screws to take out to remove stove from pallet.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents EF2 Table of Contents Store pellets at least 36 1 m away from the pellet stove IntroductionI. Pellet Standards USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Special Notes Reasons WHY the Unit OverheatedOperating Instructions Special Notes Inside Firebox 2-3 days Routine Cleaning and MaintenanceTools Required to Clean Unit Burn POT and Liner 2-3 daysFireplace Insert and BUILT-IN Heater ASH PAN Not Place Unburned or RAW Pellet Fuel in ASH PANFreestanding ASH PAN Brick Panel Post Season CLEAN-UPCleaning Plated Surfaces Screws to take out to remove stove from pallet InstallationDimensions of EF2 Freestanding Minimum Alcove width Inches 91 cm Minimum Alcove height EF2 Built-In Heater recommended Framing Or from the outside of the pedestal for the FPI or BIHVent surfaces can Fresh AIR Intake ExhaustFreestanding Fireplace Insert Built-In Heater Fresh Air Intake Unit on it Locate the center of the exhaust Is the recommended installation set up Inside Vertical Installation Install the hearth pad Freestanding hearth mount installation overview Connect a tee or 90 degree This unit includes a 3 75 mm pedestal Corner Brackets Side surround panel swings forward RemovalStove will not light TroubleshootingStove will not start Convection blower will not function normally Stove will not function in the Auto mode when hotExhaust motor will not function normally Auger motor will not function normally Stove keeps going out Dial-a-fire has no effect on the firePotentiometer Readings Stove will not shut offWiring Diagram Parts List Fireplace Insert Stove Top Parts List Parts List Options ComponentsDPartsiagram Parts Diagram Steel To the Distributor WarrantyTo the Dealer Name of Owner Address Installation Data Sheet

EF-119 specifications

The Enviro EF-119 is an innovative, environmentally friendly vehicle that has garnered attention for its advanced technology and impressive performance characteristics. Designed with sustainability in mind, the EF-119 incorporates cutting-edge features that make it a standout choice in the green vehicle market.

One of the main highlights of the Enviro EF-119 is its electric powertrain. The vehicle is equipped with a high-capacity lithium-ion battery that offers a range of up to 300 miles on a single charge, making it ideal for both urban commuting and longer journeys. The EF-119 also features fast charging capabilities, allowing drivers to recharge their batteries to 80% in just under 30 minutes with compatible charging stations, significantly reducing downtime during travel.

In terms of design, the EF-119 boasts a sleek, aerodynamic shape that not only enhances its visual appeal but also improves energy efficiency. The vehicle's lightweight chassis is constructed from advanced composite materials, reducing overall weight while maintaining structural integrity. This design decision contributes to lower energy consumption and improved handling on the road.

The EF-119 comes equipped with an array of smart technologies that enhance the driving experience. An intuitive infotainment system offers seamless connectivity with smartphones and other devices, allowing drivers to access navigation, music, and communication apps effortlessly. Additionally, the vehicle includes advanced safety features, such as adaptive cruise control, lane-keeping assist, and a comprehensive suite of sensors that provide real-time data on the vehicle's surroundings, ensuring a safe and comfortable ride.

Another notable characteristic of the Enviro EF-119 is its regenerative braking system. This technology captures energy typically lost during braking and redirects it back into the battery, enhancing overall efficiency and extending the vehicle's range. The result is a more sustainable driving experience that reduces wear on traditional braking systems.

Overall, the Enviro EF-119 represents a significant step forward in the evolution of electric vehicles. With its impressive range, advanced safety features, and commitment to sustainability, it meets the needs of modern drivers who prioritize eco-friendly transportation without compromising on performance or style. As the automotive industry shifts towards greener alternatives, the EF-119 stands out as a leading choice for environmentally conscious consumers seeking innovation and excellence.
Top Page Image Contents