Enviro EF-119 owner manual Special Notes

Page 7

Operating Instructions

OPERATING YOUR PELLET STOVE:

1.Check and fill hopper with pellets.

2.Make sure unit is plugged into a working outlet.

3.Switch the power on by pushing the ROCKER SWITCH to the MANUAL position.

4.Turn KNOB B to the 12 o’clock position. (Lower grade pellets may need a higher setting on the feed rate). NOTE: Unit will take longer to light if the hopper has been completely emptied or is the first fire up.

5.Approximately fifteen (15) minutes after the fire was lit, the GREEN LIGHT should come on. When the GREEN LIGHT comes on, push the ROCKER SWITCH to the AUTO position. Now the stove will shut-off automatically if the fire goes out.

6.Wait until the fire is established, then turn KNOB B to the desired heat output. The stove may not be able to burn in the BLUE ZONE if poor quality wood pellets are being used. Adjust the slider-damper to the appropriate setting (see

“SLIDER/DAMPER SETTING” section.

 

Figure 2: Dial-A-Fire control panel.

KNOB “A”: Fan Controller. By adjusting the knob you will vary the rate of airflow into the room by varying the speed of the convection blower. When you first start the stove, it should be placed in the “OFF” position in order to heat the unit as quickly as possible. Once the room has come up to temperature, the control may be set to a comfortable level. *Note: The convection blower may cycle to high automatically depending on the setting of KNOBS A and B. This is a normal safety feature of the unit.

KNOB “B”: Dia-A-Fire Heat Output Knob. This knob controls the amount of heat output. The dial has a scale with the blue zone representing the coolest setting of the stove, and the red zone representing the hottest setting. The scale on knob “B” represents a range, not exact at times or fuel quantities.

Wood pellets of differing quality may affect the performance of the stove. If the stove has trouble operating at either end of its range, turn the heat output knob back slightly.

TURNING YOUR PELLET STOVE OFF:

The AUTO/MANUAL SWITCH must be in the AUTO position during operation. To turn the stove off, simply turn the HEAT OUTPUT knob (KNOB B) counter-clockwise until the knob clicks to the “OFF” position. This will stop the feed of pellets. The blowers will continue to run and cool the stove.

SPECIAL NOTES:

If the stove is left in the manual mode after the green light comes on, the auger will continue to feed pellets. Pellets may over flow the burn-pot after the fire goes out and also re-light.

The scale on KNOB B represents a range, not exact times. Wood pellets of differing quality may effect the performance and/or the heat output of the stove. If the stove has trouble operating at the end of its range, adjust the heat output knob back slightly.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents EF2 Table of Contents I. Pellet Standards IntroductionStore pellets at least 36 1 m away from the pellet stove USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Operating Instructions Reasons WHY the Unit OverheatedSpecial Notes Special Notes Inside Firebox 2-3 days Routine Cleaning and MaintenanceTools Required to Clean Unit Burn POT and Liner 2-3 daysFreestanding ASH PAN Not Place Unburned or RAW Pellet Fuel in ASH PANFireplace Insert and BUILT-IN Heater ASH PAN Cleaning Plated Surfaces Post Season CLEAN-UPBrick Panel Screws to take out to remove stove from pallet InstallationDimensions of EF2 Freestanding Minimum Alcove width Inches 91 cm Minimum Alcove height EF2 Built-In Heater recommended Framing Or from the outside of the pedestal for the FPI or BIHVent surfaces can Freestanding Fireplace Insert Built-In Heater ExhaustFresh AIR Intake Fresh Air Intake Unit on it Locate the center of the exhaust Is the recommended installation set up Inside Vertical Installation Install the hearth pad Freestanding hearth mount installation overview Connect a tee or 90 degree This unit includes a 3 75 mm pedestal Corner Brackets Side surround panel swings forward RemovalStove will not start TroubleshootingStove will not light Exhaust motor will not function normally Stove will not function in the Auto mode when hotConvection blower will not function normally Auger motor will not function normally Stove keeps going out Dial-a-fire has no effect on the firePotentiometer Readings Stove will not shut offWiring Diagram Parts List Fireplace Insert Stove Top Parts List Parts List Options ComponentsDPartsiagram Parts Diagram Steel To the Dealer WarrantyTo the Distributor Name of Owner Address Installation Data Sheet

EF-119 specifications

The Enviro EF-119 is an innovative, environmentally friendly vehicle that has garnered attention for its advanced technology and impressive performance characteristics. Designed with sustainability in mind, the EF-119 incorporates cutting-edge features that make it a standout choice in the green vehicle market.

One of the main highlights of the Enviro EF-119 is its electric powertrain. The vehicle is equipped with a high-capacity lithium-ion battery that offers a range of up to 300 miles on a single charge, making it ideal for both urban commuting and longer journeys. The EF-119 also features fast charging capabilities, allowing drivers to recharge their batteries to 80% in just under 30 minutes with compatible charging stations, significantly reducing downtime during travel.

In terms of design, the EF-119 boasts a sleek, aerodynamic shape that not only enhances its visual appeal but also improves energy efficiency. The vehicle's lightweight chassis is constructed from advanced composite materials, reducing overall weight while maintaining structural integrity. This design decision contributes to lower energy consumption and improved handling on the road.

The EF-119 comes equipped with an array of smart technologies that enhance the driving experience. An intuitive infotainment system offers seamless connectivity with smartphones and other devices, allowing drivers to access navigation, music, and communication apps effortlessly. Additionally, the vehicle includes advanced safety features, such as adaptive cruise control, lane-keeping assist, and a comprehensive suite of sensors that provide real-time data on the vehicle's surroundings, ensuring a safe and comfortable ride.

Another notable characteristic of the Enviro EF-119 is its regenerative braking system. This technology captures energy typically lost during braking and redirects it back into the battery, enhancing overall efficiency and extending the vehicle's range. The result is a more sustainable driving experience that reduces wear on traditional braking systems.

Overall, the Enviro EF-119 represents a significant step forward in the evolution of electric vehicles. With its impressive range, advanced safety features, and commitment to sustainability, it meets the needs of modern drivers who prioritize eco-friendly transportation without compromising on performance or style. As the automotive industry shifts towards greener alternatives, the EF-119 stands out as a leading choice for environmentally conscious consumers seeking innovation and excellence.
Top Page Image Contents