Enviro EF-119 owner manual This unit includes a 3 75 mm pedestal

Page 24

 

 

Installation

INSTALLATION FOR A BUILT-IN HEATER:

 

Combustible

 

This unit includes a 3” (75 mm) pedestal

 

and surrounding faceplates. The part of the

materials and

 

structure

 

unit behind the faceplate can be enclosed

 

 

 

with combustible material. It has 1” (25

Surround Panel

Wall

mm) standoffs to establish clearances to

 

 

thimble

combustibles to the back, top and sides.

 

 

12"

Refer to “CLEARANCES TO COMBUSTIBLES - BUILT-IN

 

 

(30.5 cm)

 

 

45°

HEATER“ and Figure 6 and 7 for the size and

 

 

placement of the alcove to be built for the

 

 

elbow

 

 

 

unit.

6"

 

Rodent

For the venting refer to “HORIZONTAL EXHAUST

(15 cm)

 

mesh cap

THROUGH WALL INSTALLATION - FREESTANDING“.

 

 

Fresh air

 

 

 

intake

 

Non-combustible

 

Existing floor

 

 

(combustible)

 

floor protection.

3" (7.5 cm)

 

 

Pedestal

 

 

Figure 30: Built-in heater installation.

INSTALLATION OF CONTROL PANEL INTO SURROUND PANEL - FPI AND BIH:

When installing the control panel into the surround panel, the surround does not need to be assembled. The control board will be found in behind the firebox.

Place the control panel on the backside of the right surround panel so the hinge is on the outside and the top and bottom holes on the control panel line up with those on the surround. Attach using two

(2) T-20 screws through the front of the surround into the circuit board control panel.

After the surround has been assembled and is ready to be installed on the unit, plug the wiring harness into the control panel (see Figure 32).

Figure 31: Control Panel Cover.

����

Figure 32: Control Panel Back

- Timer.

24

Image 24
Contents EF2 Table of Contents Introduction I. Pellet StandardsStore pellets at least 36 1 m away from the pellet stove USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Reasons WHY the Unit Overheated Operating InstructionsSpecial Notes Special Notes Routine Cleaning and Maintenance Tools Required to Clean UnitBurn POT and Liner 2-3 days Inside Firebox 2-3 daysNot Place Unburned or RAW Pellet Fuel in ASH PAN Freestanding ASH PANFireplace Insert and BUILT-IN Heater ASH PAN Post Season CLEAN-UP Cleaning Plated SurfacesBrick Panel Installation Screws to take out to remove stove from palletDimensions of EF2 Freestanding Minimum Alcove width Inches 91 cm Minimum Alcove height Or from the outside of the pedestal for the FPI or BIH EF2 Built-In Heater recommended FramingVent surfaces can Exhaust Freestanding Fireplace Insert Built-In HeaterFresh AIR Intake Fresh Air Intake Unit on it Locate the center of the exhaust Is the recommended installation set up Inside Vertical Installation Install the hearth pad Freestanding hearth mount installation overview Connect a tee or 90 degree This unit includes a 3 75 mm pedestal Corner Brackets Removal Side surround panel swings forwardTroubleshooting Stove will not startStove will not light Stove will not function in the Auto mode when hot Exhaust motor will not function normallyConvection blower will not function normally Auger motor will not function normally Dial-a-fire has no effect on the fire Potentiometer ReadingsStove will not shut off Stove keeps going outWiring Diagram Parts List Fireplace Insert Stove Top Parts List Parts List Options ComponentsDPartsiagram Parts Diagram Steel Warranty To the DealerTo the Distributor Installation Data Sheet Name of Owner Address

EF-119 specifications

The Enviro EF-119 is an innovative, environmentally friendly vehicle that has garnered attention for its advanced technology and impressive performance characteristics. Designed with sustainability in mind, the EF-119 incorporates cutting-edge features that make it a standout choice in the green vehicle market.

One of the main highlights of the Enviro EF-119 is its electric powertrain. The vehicle is equipped with a high-capacity lithium-ion battery that offers a range of up to 300 miles on a single charge, making it ideal for both urban commuting and longer journeys. The EF-119 also features fast charging capabilities, allowing drivers to recharge their batteries to 80% in just under 30 minutes with compatible charging stations, significantly reducing downtime during travel.

In terms of design, the EF-119 boasts a sleek, aerodynamic shape that not only enhances its visual appeal but also improves energy efficiency. The vehicle's lightweight chassis is constructed from advanced composite materials, reducing overall weight while maintaining structural integrity. This design decision contributes to lower energy consumption and improved handling on the road.

The EF-119 comes equipped with an array of smart technologies that enhance the driving experience. An intuitive infotainment system offers seamless connectivity with smartphones and other devices, allowing drivers to access navigation, music, and communication apps effortlessly. Additionally, the vehicle includes advanced safety features, such as adaptive cruise control, lane-keeping assist, and a comprehensive suite of sensors that provide real-time data on the vehicle's surroundings, ensuring a safe and comfortable ride.

Another notable characteristic of the Enviro EF-119 is its regenerative braking system. This technology captures energy typically lost during braking and redirects it back into the battery, enhancing overall efficiency and extending the vehicle's range. The result is a more sustainable driving experience that reduces wear on traditional braking systems.

Overall, the Enviro EF-119 represents a significant step forward in the evolution of electric vehicles. With its impressive range, advanced safety features, and commitment to sustainability, it meets the needs of modern drivers who prioritize eco-friendly transportation without compromising on performance or style. As the automotive industry shifts towards greener alternatives, the EF-119 stands out as a leading choice for environmentally conscious consumers seeking innovation and excellence.