Enviro 1200 Freestanding, C-10240, 1700 Freestanding Back View of Freestanding Unit with Fan Kit

Page 34

Installation

OPTIONAL FAN INSTALLATION - FREESTANDING:

Refer to FAN WIRING DIAGRAM before installing your optional fan

kit.

1.Remove the fan assembly from the box and inspect for any damage to the assembly. If damage is noticed call your dealer, distributor or courier company and have components replaced before installing kit.

2.Remove the knock out at the bottom of the back panel of the appliance by using a flat head screwdriver as a lever, hook the tip of the screwdriver under the panel beside the tabs and push the panel out.

3.Install two (2) T-20 screws into the top two (2) holes. Place the blower assembly over these two (2) screws.

4.Ensure the temperature sensor will touch the unit when mounted. If it does not touch, adjust the sensor so it does. Tighten the two (2) top screws and install the two (2) bottom screws and tighten.

5.Plug the fan assembly in and check for proper operation.

FAN REMOVAL - INSERT:

Figure 41: Back View of Freestanding

Unit with Fan Kit.

The fan kit is pre-installed into the left shroud that comes with your unit. If a decorative set of shroud plates is purchased, the fan assembly must be removed from the shroud to installed the decorative

plates (refer to “REMOVAL OF THE SHROUDS - INSERT”).

1) Disconnect all electrical connections for the fan kit.

2) Remove the four (4) T-20 screws that hold the fan mounting plate to the shroud. If the fan needs to be removed from its mounting plate, use a 1⁄4” socket and wrench to remove the six

(6) bolts holding the fan housing to the plate.

3) Remove the fan control knob and nut from the front of the shroud and pull the controls out the back.

4) Slide the plug out the front of the pod.

5) Install the fan kit into the new shroud by

 

following steps 1 through 4 in reverse order.

 

Refer to FAN WIRING DIAGRAM to ensure the fan is

 

reconnected properly.

Figure 42: Insert Unit with Fan.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Wood Stove Table of Contents Safety Precautions Operating Instructions First StartCreosote ITS Formation and Removal Helpful Hints Worth Repeating What type of wood is best to use as firewood? What can cause a poor draft? 1200 Air Flow Path Specifications Capacity Feet3 0.0708 meter3 Approximate heating area † From front of unit to edge of floor protection Maintain These Minimum Clearances to Unshielded Combustibles 1700 Freestanding Clearance to Combustibles 1200 Insert Dimensions 1200 Freestanding Flat Top Dimensions 1700 Freestanding Flat Top Dimensions 1200 Freestanding with Fan Kit Dimensions Installation Bolts to removeInstalling Heat Shield Recommended Height for Flue Pipe Chimney Through Wall Method a Roof Clearances Shield if required Installation into a masonry chimney Venting Outside AIR Insert Installation into existing fireplace With hearth Attaching removable flue Total Bricks Model 1700 Brick Placement Do not USE Door if Glass is Broken Installation of Ceramic Baffle Back View of Freestanding Unit with Fan Kit Removal of right pod This will keep the trim tight Parts List Parts List Parts Diagram Parts Diagram Pedestals & Legs Parts Diagram Fireplace Insert Warranty Limited Five 5 Year Warranty Limited One 1 Year WarrantyExclusions and Limitations Warranty Installation Data Sheet

1200 Fireplace Insert, 50-1040, 1200 Freestanding, 1700 Fireplace Insert, C-10240 specifications

The Enviro 1700 Freestanding, C-10240, 1700 Fireplace Insert, and 1200 Freestanding models are exceptional choices for those seeking both aesthetic appeal and efficient heating performance. These fireplaces combine advanced technology with modern design, making them suitable for various home styles while providing effective warmth.

One of the standout features of the Enviro 1700 Freestanding unit is its elegant design. Its clean lines and contemporary look allow it to blend seamlessly into any room. The fireplace is constructed from high-quality materials, ensuring durability and longevity. This model is designed to produce maximum heat output while minimizing wood consumption, making it an eco-friendly option.

The C-10240 model, designed for those who prefer a traditional fireplace insert, showcases a unique combination of classic design with innovative technology. This insert provides the warmth and ambiance of a classic wood-burning fire without compromising efficiency. It is equipped with a powerful combustion system that ensures a clean burn, reducing emissions and providing a sustainable heating solution for homes.

The 1700 Fireplace Insert model is perfect for homeowners looking for an effective way to upgrade their existing fireplace. This insert offers the benefits of modern heating technology while maintaining the charm of a traditional fireplace. It features an expansive viewing area, allowing for an impressive display of flames and creating a cozy atmosphere. Its robust design ensures that it fits snugly into existing hearths, providing an instant upgrade.

The 1200 Freestanding model is designed for versatility. Whether placed in the center of a room or in a corner, it offers a 360-degree view of the fire. This model utilizes advanced clean-burning technology, ensuring that the fire produces minimal smoke and pollutants. Its efficient heat distribution system allows for optimal warmth, making it an excellent choice for heating larger spaces.

All these models feature advanced air wash systems that keep the glass door clean for unobstructed views of the flames. Additional options, such as direct venting and multi-fuel capabilities, further enhance their flexibility and performance. Whether you opt for the 1700 Freestanding, C-10240, 1700 Fireplace Insert, or the 1200 Freestanding, you can be assured of reliable heat, stunning views, and environmentally friendly operation throughout the colder months.
Top Page Image Contents