Enviro EG40-071 owner manual 50% turn down HI-LOW Regulator

Page 11

Initial Installation

FUEL CONVERSION:

WARNING: This conversion kit shall be installed by a qualified service technician in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or CO poisoning may result. The qualified service agency is responsible for the proper installation of this kit. The installation is not proper or complete until the operation of the converted appliance is checked as specified in the owner’s conversion kit.

Please read and follow these instructions. Also please read the instruction guidelines provided by S.I.T on how to remove and install the HI-LOW regulator.

STEP 1. Carefully inspect all parts supplied with this conversion kit. STEP 2. Shut the gas off and disconnect the main gas line from the unit.

STEP 3. Open the door by unscrewing the 1⁄2” bolt on the right hand side of the stove. Lift door off the hinges mounted on the left-hand side.

STEP 4. Carefully remove the log set and ember material if they are installed.

STEP 5. Remove the two (2) T-20 screws on the burner tray located between the front and rear burners. STEP 6. Change the regulator on the top of the gas valve. (Follow the instructions provided by S.I.T)

STEP 7. To change the pilot, pull the pilot hood straight up to access the pilot injector, using a 5/32” Allen key, remove the pilot injector.

STEP 8. Install new pilot injector supplied with the conversion kit. Screw the new injector inside the pilot assembly and re-install the hood by placing the hood on the assembly, line up the keyway and snap into place

STEP 9. Remove the two (2) main burner orifices using a 1⁄2” deep socket.

STEP 10. Install the two (2) new orifices supplied making sure that the orifices are in the correct location. Be sure to put a bead of pipe thread sealant or approved Teflon tape on the orifices before installing them into the burner assembly.

STEP 11. Re-install burner tray, log set and door. Also refer to “Installing Log Set and Embers.”

STEP 12. Reconnect the gas line to the unit. Do a leak check using soap and water solution or an approved method on the gas supply and the pilot tubing.

STEP 13. Re-light the appliance to ensure proper operation and proper flame appearance. Be sure to adjust the venturi setting to achieve an efficient flame in the fireplace.

STEP 14. MAKE SURE that the sticker provided by S.I.T is installed to signify that this valve has been converted to a different type of fuel. Also make sure that the rating plate has a conversion label to show that this unit has been converted to a different fuel type.

A VISUAL CHECK OF THE REGULATOR KNOB IS NECESSARY TO DETERMINE WHETHER OR NOT THE REGULATOR IS THE CORRECT PART. A 50% TURN DOWN REGULATOR WILL HAVE ONLY ONE CORNER ON THE KNOB.

1

- 50% turn down HI-LOW Regulator

Table 3: Orifice Information.

 

3

- T-20 Torx screws

 

 

 

 

 

 

Natural Gas

 

Propane

1

- T-20 tamper proof Torx screwdriver bit

 

 

 

 

 

 

Pilot Orifice

.62 mm

 

.35 mm

1

- pilot injector

 

 

 

 

 

2

- Main orifice

Burner Orifice Front

#48 DMS

 

#55 DMS

Labels to show conversion.

Burner Orifice Rear

#43 DMS

 

#54 DMS

 

 

 

 

 

 

 

 

Venturi Setting Front

1⁄8” min.

 

3/16” min.

 

 

Venturi Setting Rear

3/16” min.

 

1⁄2” Min

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents EG40 BV General Safety PrecautionsFor Your Safety Table of Contents Vented GAS Fireplace Heater EG40 BV NG/LPG Codes And ApprovalsEG40 Exterior Dimensions SpecificationsQualified Installers only Initial InstallationHeight of Vertical Termination Straight vertical installation Wiring of a Thermostat Turn the unit off and remove the log set 50% turn down HI-LOW Regulator To Test Valve Pressures GAS Line ConnectionLog Placement Secondary InstallationLog Placement with Embers What to do if YOU Smell GAS Operating InstructionsOpening the Door Routine Maintenance and ServiceCleaning the Inside of the Firebox Cleaning Plated SurfacesProblem Possible Cause Solution Trouble ShootingParts List Reference Part Description Part Number Parts Diagram Chassis Parts Diagram Gas Tray & DoorTo the Distributor WarrantyInstallation Data Sheet

EG40-071 specifications

The Enviro EG40-071 represents a cutting-edge advancement in eco-friendly technology, engineered for both performance and sustainability. This device is a perfect embodiment of modern environmental solutions, making it an ideal choice for various applications ranging from industrial processes to residential use.

One of the standout features of the Enviro EG40-071 is its high efficiency. The unit utilizes advanced energy management systems that optimize power consumption while delivering impressive output. With a focus on reducing environmental impact, the EG40-071 is designed to operate with minimal energy waste, thereby lowering operational costs and promoting greener practices.

Moreover, the technology integrated into the Enviro EG40-071 is state-of-the-art. It includes sophisticated monitoring systems that provide real-time data on performance metrics. This feature allows users to track energy usage, emissions, and operational efficiency, enabling informed decision-making and streamlined performance. The device is also equipped with IoT capabilities, facilitating remote access and management through connected devices. This modern connectivity feature means users can monitor and control the unit from anywhere, enhancing convenience and overall functionality.

In terms of design, the Enviro EG40-071 boasts a robust and compact structure, making it suitable for various installation settings. Its modular design enables easy integration into existing systems, while the durable materials used in its construction ensure longevity and reliability even in challenging environments. Additionally, the device adheres to stringent safety standards, providing peace of mind for users.

One of the key characteristics of the Enviro EG40-071 is its versatility. It can be utilized in diverse applications, including HVAC systems, industrial machinery, and renewable energy projects. This adaptability makes it a valuable asset for businesses and households striving to reduce their carbon footprint. Furthermore, the EG40-071 contributes to compliance with environmental regulations, allowing users to align with sustainability goals and practices.

In conclusion, the Enviro EG40-071 combines advanced technology, efficiency, and versatility, making it a significant player in the realm of eco-friendly solutions. With features that support energy management and monitoring, alongside a robust and modular design, it stands out as a key component for those looking to embrace sustainable innovation in their operations. The Enviro EG40-071 is not just a product; it is a commitment to a greener future.
Top Page Image Contents