Initial Installation, Qualified Installers only

Initial Installation

QUALIFIED INSTALLERS ONLY

VENTING:

This model must have a vent opening in the rear of the unit. Confirm this and also check that the label on the right side panel door states “Vented Room Heater”.

WARNING: This appliance has been designed to operate by drawing combustion air and dilution air from the room. The draft hood located in the same atmospheric pressure zone as the combustion air inlet to the appliance. It is also designed to draw room air for proper heat circulation from the rear of the unit. Blocking or modifying the louvers in any way can create hazardous situations, either through poor venting or by overheating. It is important that this unit has sufficient air circulation for proper venting and combustion thus provisions must be made for the supply of adequate combustion and ventilation air.

WARNING: Operation of this heater when not connected to a properly installed and maintained venting system or tampering with the vent safety shutoff system can result in carbon monoxide (CO) poisoning and possible death.

THE APPLIANCE CANNOT BE CONNECTED TO A CHIMNEY FLUE SERVICING

A SEPARATE SOLID FUEL BURNING APPLIANCE.

FLUE GAS SPILL SWITCH:

NOTE: This heater must be properly connected to a venting system. This heater is equipped with a vent safety shutoff system designed to protect against improper venting of combustion products. This safety switch is located on the rear of the appliance close to the drafthood relief opening.

If the switch trips more than once, the chimney should be inspected by a qualified service technician for possible blockage or severe down draught conditions.

MANUFACTURER’S GENERAL VENTING GUIDELINES:

This information is compiled by the manufacturer as a very general rule for single appliance venting of the EG40 gas stove with 4 inch Type B gas vent. Refer to the Venting manufacturer’s directions for installation.

Venting code and regulations may vary from area to area, please check with the local, state/provincial codes regarding the suitability of your application.

For other special venting requirements, please refer to the local, state/provincial or national codes.

The venting system should be assembled and installed according to the vent manufacturer’s instructions and the local, state/provincial or national codes.

GENERAL VENTING FOR THE EG40:

This stove should be vented by certified 4” (10 cm) Type B Gas Vent or a flexible gas vent liner that may be encased in 6” (15 cm) decorative stove pipe. The flue collar of the appliance will fit inside of standard vent and may be fastened directly to the vent.

The ENVIRO incorporates its own internal draft hood, so no additional external draft hood is required.

Check periodically that the vent is unrestricted and an adequate draught is present when the unit is in operation.

EG40-071 specifications

The Enviro EG40-071 represents a cutting-edge advancement in eco-friendly technology, engineered for both performance and sustainability. This device is a perfect embodiment of modern environmental solutions, making it an ideal choice for various applications ranging from industrial processes to residential use.

One of the standout features of the Enviro EG40-071 is its high efficiency. The unit utilizes advanced energy management systems that optimize power consumption while delivering impressive output. With a focus on reducing environmental impact, the EG40-071 is designed to operate with minimal energy waste, thereby lowering operational costs and promoting greener practices.

Moreover, the technology integrated into the Enviro EG40-071 is state-of-the-art. It includes sophisticated monitoring systems that provide real-time data on performance metrics. This feature allows users to track energy usage, emissions, and operational efficiency, enabling informed decision-making and streamlined performance. The device is also equipped with IoT capabilities, facilitating remote access and management through connected devices. This modern connectivity feature means users can monitor and control the unit from anywhere, enhancing convenience and overall functionality.

In terms of design, the Enviro EG40-071 boasts a robust and compact structure, making it suitable for various installation settings. Its modular design enables easy integration into existing systems, while the durable materials used in its construction ensure longevity and reliability even in challenging environments. Additionally, the device adheres to stringent safety standards, providing peace of mind for users.

One of the key characteristics of the Enviro EG40-071 is its versatility. It can be utilized in diverse applications, including HVAC systems, industrial machinery, and renewable energy projects. This adaptability makes it a valuable asset for businesses and households striving to reduce their carbon footprint. Furthermore, the EG40-071 contributes to compliance with environmental regulations, allowing users to align with sustainability goals and practices.

In conclusion, the Enviro EG40-071 combines advanced technology, efficiency, and versatility, making it a significant player in the realm of eco-friendly solutions. With features that support energy management and monitoring, alongside a robust and modular design, it stands out as a key component for those looking to embrace sustainable innovation in their operations. The Enviro EG40-071 is not just a product; it is a commitment to a greener future.