Harman Stove Company P61-2 manual P61ESP-2 Espcontrolcontrol

Page 14

P61ESP-2 ESPCONTROLCONTROL

Power Light Indicates power to the control.

Status Light

Will be lit in either stove or room temp mode when pointer is not within off position band except after normal shut down. Blinks to indicate errors listed listed below.

Indicates power to distribution blower.

Indicates Power to combustion blower

Indicates Power to the feed motor.

Temp dial

Allows you to adjust the Room temperature in Room Temp Mode using the outer scale marked in degrees Fahrenheit. It also allows you to adjust the stove temperature while in Stove Temp Mode using the inner scale marked from 1 to 7.

Feed adjuster Sets the maximum feed rate

Test

Runs all motors at full speed for two minutes to check operation. After two minutes the stove will go to minimum burn and the blowers will alternate from high to low every two minutes to remind you that you are still in "Test Mode".

Distribution Blower speed adjustment range.

Mode Selector

Allows you to choose between Room Temp Mode, Stove Temp Mode, or OFF. Also allows you to vary the distribution blower speed by turning the knob to the high or low side of each mode.

STATUS LIGHT ERROR MESSAGES:

1 Blink: Indicates control board self diagnostic fail- ure. This requires a manual reset*.

2 Blinks:Indicates that the jumper (J2) on the rear of the control board is not connected. Without this jumper the unit will only burn at minimum rate.

3 Blinks: Indicates ESP (Exhaust Sensing Probe) failure. This requires a manual reset*.

4 Blinks: Can occur only in Room Temp Mode and indicates Room Sensing Probe failed or not installed. If a Room Sensing Probe is then installed the status light will automatically reset.

(Note) only after unit has warmed up.

6 Blinks : Indicates that the control has calculated14

poor or incomplete combustion occurring for more than 50 minutes. See Troubleshooting section for more details.

*Manual reset, disconnect power cord for a few seconds and reconnect. If error still occurs call your Dealer.

Image 14
Contents Installation & Operating Manual Safety NoticePage Table of Contents Unpacking Assembly and InstallationRemoving or Installing rear cover panels FirebrickMobile Home Installation InstallationInstalling Venting With outside air installed, 18îWith outside air installed, 6 feet Vent Pipe Outside Air#2 Preferred method Ventingnting#1 Preferred method VentingVenting #4 Installing into an existing chimney US only#5 Installing into an existing fireplace chimney US only #7 Installing into an existing chimney US and Canada VentingVenti Minimum flue vent configuration #8 Installing through the ceiling ventFill the hopper with pellets P61-2 Manual Start UPOperation Starting First Fire Shut-Down Procedure When to use Stove Temp ModeWhen to use Room Temp Mode P61-2 Manual IGNITION/OPERATIONPower Light Indicates power to the control Status Light P61ESP-2 EspcontrolcontrolRoom Sensor and Rear Shield Installation Room Sensor Installation Rear ShieldsRemoving Ashes MaintenanceCleaning Soot and Fly Ash Trouble-Shooting Cleaning Burn PotP61-2 Feeder and Specifications Specifications23.5P61-2 Wiring Diagram Door Options Optional TrimHopper Extension OptionsSide Heat Shields P61 Parts List 90-05802Harman Gold Warranty Harman Gold Warranty Year Transferable Limited

P61-2 specifications

The Harman Stove Company P61-2 is a premier pellet stove that stands out for its blend of efficiency, convenience, and advanced technology. Designed for both aesthetics and functionality, the P61-2 offers homeowners an exceptional heating solution for their living spaces.

One of the standout features of the P61-2 is its robust heating capability. This stove can produce an impressive heat output of up to 50,000 BTUs, effectively warming spaces up to 2,500 square feet. This makes it ideal for larger rooms or open floor plans, ensuring that the ambient temperature remains comfortable even on the coldest winter nights.

The P61-2 is designed with an innovative hopper capacity of 60 pounds, allowing for extended burn times of up to 24 hours on a single fill. This feature significantly reduces the frequency of refueling, making it an incredibly user-friendly option. The stove's automated feed system further enhances convenience by regulating the flow of pellets according to the heat setting, ensuring a consistent and efficient burn.

Another defining characteristic of the P61-2 is its advanced control system. Featuring a digital thermostat, users can easily set and adjust temperatures, providing a seamless heating experience. The stove also includes a programmable timer, allowing homeowners to schedule heating cycles according to their needs, ensuring warmth is on when it's needed most.

In terms of design, the P61-2 boasts a modern aesthetic that can complement various home interiors. It is available in multiple finishes, including classic black, providing a touch of elegance alongside powerful heating performance. The large viewing window allows users to enjoy the mesmerizing flames while benefiting from the stove's efficient heating capabilities.

The P61-2 also emphasizes environmentally conscious heating. It meets stringent EPA standards with low emissions, making it a cleaner alternative to traditional wood-burning stoves. This not only benefits the environment but also contributes to better indoor air quality.

Additionally, the Harman Stove Company has integrated user-friendly features such as a self-cleaning firepot and easy access to components for maintenance. This ensures that keeping the P61-2 in optimal condition is a straightforward process.

In conclusion, the Harman Stove Company P61-2 is a technologically advanced, efficient, and stylish pellet stove that masterfully combines performance with practicality. Whether for its powerful heating capabilities, user-friendly controls, or modern aesthetics, the P61-2 remains a top choice for those seeking a reliable and effective heating solution for their homes.