CFM warranty Installation, Preparing the UVHB10, Optional FK24 Fan Hook-Up

Page 5

PYROMASTER® UVHB10 Vent-Free Heaters

Installation

Preparing the UVHB10

The UVHB10 may only be used with the approved mantel and hearth assembly.

1.After determining a location, open the mantel hearth base carton and place into position on a solid surface. NOTE: Be sure to level the base before setting the UVHB10 heater in place.

2.Place the heater on the hearth base centering side to side and 3/4" from the back edge of the hearth base (Fig. 1)

3.Bend the lower mounting tabs down against the hearth base and secure with two (2) wood screws (Fig. 1)

Optional FK24 Fan Hook-Up

NOTE: The FK24 fan should be installed before the mantel cabinet is complete. Later installation will be more difficult.

1.Remove the front screen by lifting up on the screen, pulling out on the bottom and pulling down.

2.Remove the three (3) retaining screws that secure the hood to the unit. (Fig. 3)

Hood

FP1224

Fig. 3 Remove hood.

3.Remove the 13 screws that secure the outer top to the unit. (Fig. 4)

4.Remove the two (2) screws holding the bracket to the fan.

5.Remove the two (2) wires attached to the fan and assemble the fan to the bracket as shown in Figure 5.

6.Attach the electrical flag connectors to the fan motor using the wire extension. (Fig. 6)

7.Feed the wire down the 1-inch diameter hole in the left side of the radiant shield. Push the plastic bushing in the hole.

20004232

Outer Top

 

 

 

FP1225

Fig. 4

Remove outer top.

 

 

 

 

Screws

Fan Bracket

 

 

 

 

 

Radiant Shield

 

 

 

Fan

 

 

 

Burner Tube

 

 

 

Shield

 

 

 

Thermo-disc

 

 

 

Hex Nut

 

 

 

Rheostat

 

To Receptacle

FP1226

Fig. 5

Attach fan to bracket.

 

 

Speed

Temperature

Fan

 

Control

Sensor

 

Wire Extension

FP394A

Fig. 6 Wiring diagram.

8.Hook the wire extension to the wire leads from the fan control box. NOTE: These leads were hooked to the motor earlier.

9.Mount the thermo-disc to the left log support tab and secure with one (1) nut.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents UVHB10 General Information Table Of ContentsUVHB10 Series Gas Appliance Corner Cabinet Description Gas SpecificationsMinimum Clearances Gas Supply PressuresOptional FK24 Fan Hook-Up InstallationPreparing the UVHB10 Final Assembly Installing Brass TrimFan Operation UVHB10 Logset Run Gas Line from Its Source to the HeaterWhen Used as a Heating Appliance Flame AdjustmentOperation First FiringWhat to do if YOU Smell GAS To Turn Off Gas To HeaterHandle only When Cool MaintenanceCleaning the Standing Pilot Control System Symptom Possible Causes Corrective Action TroubleshootingUVHB10 Replacement Parts List UVHB10Accessories Limited 2/20 Year Warranty

UVHB10 specifications

The CFM UVHB10 is a cutting-edge vehicle that represents a significant advancement in the world of electric mobility and urban transport solutions. Designed for efficiency and versatility, the UVHB10 is an all-electric, low-floor bus that serves as a strong response to the rising demand for green public transportation options.

One of the standout features of the CFM UVHB10 is its impressive battery technology. Equipped with a high-capacity lithium-ion battery, this bus can operate for extended periods on a single charge, thus ensuring that public transit systems can maintain reliable service without frequent downtime for recharging. The energy management system is optimized to provide maximum efficiency, allowing the bus to cover significant distances while minimizing energy consumption.

In terms of capacity, the CFM UVHB10 can accommodate a large number of passengers, making it an ideal solution for urban areas experiencing high ridership levels. Its spacious interior, coupled with wide entryways, ensures quick boarding and alighting, which is crucial during peak travel times. The low-floor design not only aids accessibility for passengers with limited mobility but also enhances passenger comfort overall.

The UVHB10 boasts advanced safety technologies that are increasingly becoming essential in modern public transport vehicles. It comes equipped with an integrated collision avoidance system, advanced braking features, and real-time monitoring capabilities. These technologies work together to reduce the risk of accidents and enhance passenger safety.

Furthermore, the bus incorporates smart connectivity features that allow for real-time tracking of routes and customer service enhancements. Passengers can receive updates through mobile applications about bus locations, estimated arrival times, and service disruptions.

The exterior design of the CFM UVHB10 is both functional and modern, featuring a sleek profile that minimizes air resistance, further contributing to energy efficiency. The vehicle is also designed with sustainable materials, aligning with the eco-friendly ethos of electric transportation.

Overall, the CFM UVHB10 represents a forward-thinking approach to public transit. By combining innovative technologies with practical features for passengers and operators alike, it positions itself as a leading choice in the shift towards environmentally sustainable urban mobility solutions. With its powerful performance, extensive range, and commitment to safety, the UVHB10 is set to change the dynamics of public transportation in cities around the world.
Top Page Image Contents