Euro-Pro SV1106 manual Troubleshooting Guide & Replacement Parts

CARE AND MAINTENANCE - cont.

fig. 13 fig. 14 fig. 15

fig. 17b

TROUBLESHOOTING GUIDE & REPLACEMENT PARTS

PROBLEM	SUGGESTED SOLUTION
Vacuum will not operate	1	The battery may be depleted. Charge the vacuum until the complete oval
		around the power button is illuminated, indicating a complete charge.
	2	See “Restarting after a jam” on page 8.
Charging indicator does not	1	Check to see if the charge adapter is plugged in properly to the outlet and to
illuminate		the charge stand.
	2	Ensure that the vacuum is properly seated in the charging base.
	3	Ensure there is no debris accumulated on the metal charge contacts on the
		back of the nozzle and on the charge base.
	4	Ensure that the electrical outlet is supplying power to the charger. Check the
		fuse/breaker.
Motorized brush will not work	1	See “Cleaning the Motorized Brush and Clearing Blockages” on page 7 and
		“Restarting after a jam” on page 8.
	2	Ensure that the motorized brush is properly attached.

fig. 16 fig. 17a fig. 18

Vacuum will not pick up or suction power is weak

1	Empty the dust cup container.
2	Remove the dust cup filter, check for blockages and remove. Clean or
	replace the dust cup filter (See “Replacement Parts” below). Note: It is
	important to clean the dust cup filter every month.

4Inspect the rotating brush for a build-up of debris. Remove anything wound around the brush by carefully cutting it with scissors. The brush roll is equipped with a raised cutting guide to make inserting scissors easier. Avoid damaging or cutting the bristles. (fig. 13)

5Use a flashlight to inspect inside the air duct at the bottom of the main body and remove any debris or blockages that may be there. Reattach the motorized brush, ensuring it clicks into place.

6Remove the dust cup and use the flashlight to check the air path on the spine of the vacuum and remove any debris or blockages. Then replace the dust cup.

BRUSH BAR REMOVAL

1For easier cleaning, the brush roll can be removed from the nozzle. Using a coin, turn the dial next to the brush roll access door to the unlock position. (fig. 14) Remove the brush roll access door.

(fig. 15)

2Slip the black belt off of the white gear and lift out the brush roll. (fig. 16)

BRUSH BAR INSERTION

1To reinsert the brush roll, first slip the black belt onto the white gear (fig. 17a), then align the white square on the opposite side of the brush roll into the square slot. (fig. 17b)

2Align the white square on the belt side and position into its slot. (fig. 18)

3Replace the door, inserting the wheel side first. Use a coin to move the dial to the lock position.

RESTARTING AFTER A JAM

If the indicator light around the power button flashes, the brush bar has jammed and will cease to operate.

1	Turn the unit off and allow it to
	cool down for 10 seconds.
2	Ensure that nothing is blocking
	the motorized brush or wrapped
	around the brush bar.
3	Turn the power on and the unit

3	The battery may need to be charged, charge until the complete oval around
	the power button is illuminated.
4	Ensure that the motorized brush is properly attached.

Dust escapes from vacuum	1	Empty the dust cup container.
	2	Ensure that the filter is inserted completely into its holder below
		the dust cup.
	3	Check for punctures in dust cup filter or cracks in the dust cup and replace.
Vacuum turns off on its own	1	Charge the unit until the complete oval around the power button is
		illuminated.
Run time has decreased over time	1	Perform the following steps:

a Charge the vacuum for a minimum of 7 hours. b Run the vacuum until it turns itself off.

c Charge the vacuum for a minimum of 7 hours.

REPLACEMENT PARTS

A	XA1106	Charging Adapter
B	XBT1106	Battery pack
C	XF1100	Filters (2)

For any other servicing, call Customer Support at 1-800-798-7398

or visit www.sharkclean.com

8 TOLL FREE: 1-800-798-7398

should operate normally.

www.sharkclean.com 9