Black & Decker VPX2102, 90521333 Charging Procedure, Charge Indicators, Daisy Chain Figure C

Page 8

90521333 VPX2102 Hand Vac 8/2/07 7:44 AM Page 8

CHARGING PROCEDURE

1.Plug the charger into an appropriate outlet before inserting the battery pack.

2.Insert the battery pack into the charger (figure B). Be sure the pack is fully

seated in the charger. While charging, the red (charging) LED will flash continuously (slowly) indicating that the charging process has started.

3.The completion of charge is indicated by the red LED becoming solid. (approximately 5- 6 hours) The pack is fully charged and may be used at this time or left on the charger.

4.Recharge discharged batteries as soon as possible after use or battery life may be greatly diminished.

CHARGE INDICATORS

Replace Pack:

These chargers are designed to detect certain problems that can arise with battery packs which would be indicated by the red light flashing at a fast rate. If this occurs, re-insert battery pack. If problem persists, try a different battery pack to determine if the charger is OK. If the new pack charges correctly, then the original pack is defective and should be returned to a service center for recycling. If the new battery pack gives the same trouble indication as the original, have charger tested at an authorized service center. Note: It may take as long as fifteen minutes for the charger to determine that the pack is defective.

If the battery pack is too hot or too cold, the LED will alternately blink fast and slow, one flash at each speed and repeat.

DAISY CHAIN (FIGURE C)

Single and dual port chargers can be electrically connected in any order up to a maximum of 4 chargers. Each charger has a power-in cord (which plugs into the electrical outlet) and a power-out cord (which plugs into the next charger).

To connect chargers in a daisy chain:

1.) Plug the power-in cord into an electrical outlet.

2.) Remove the power-in cord from the next charger and plug in the power-out cord from the charger that is now plugged into the outlet.

3.) Repeat this process for the remaining chargers.

Chargers that are daisy chained together operate independently as though each one was plugged into a sperate outlet therefore a battery can be removed from anywhere along the daisy chain without affecting the other chargers.

LEAVING THE BATTERY IN THE CHARGER

The charger and battery pack can be left connected indefinitely with the LED illuminated. You may see the LED return to flashing (charging) state, as the charger will occasionally “top off “ the battery charge.

IMPORTANT CHARGING NOTES

1.Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the battery pack.

Note: The charger will not charge a battery pack if the pack temperature is below approximately 32°F (0°C) or above 122°F (50°C). The battery pack should be left in the charger and the charger will begin to charge automatically when the cell temperature warms up or cools down.

2.The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an uninsulated trailer.

3.If the battery pack does not charge properly:

a.Check current at receptacle by plugging in a lamp or other appliance

b.Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights.

c.Move charger and battery pack to a location where the surrounding air temperature is approximately 65°F - 75°F (18°- 24°C).

d.If charging problems persist, take the tool, battery pack and charger to your local service center.

4.The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the charging procedure. You may also charge a partially used pack whenever you desire with no adverse affect on the battery pack.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents 2VPXTM Hand VAC VEA EL Español EN LA ContraportadaImportant Safeguards Never Leave Vacuum Running UNATTENDED. Turn Power OFF Functional Description 90521333 VPX2102 Hand Vac 744 AM Important Safety Instructions for Battery Chargers Important Safety Instruction for Battery Packs IntroductionRead ALL Instructions Storage RecommendationsCharging Procedure Charge IndicatorsLeaving the Battery in the Charger Daisy Chain Figure CSwitching on and OFF Figure F Battery LED Indicators Figure GCleaning the Product Figs . H-M Operating InstructionsAccessories MaintenanceService Information Full TWO-YEAR Home USE Warranty FiltersPossible Cause ProblemTroubleshooting Mode D’EMPLOI Importantes Mises EN Garde 90521333 VPX2102 Hand Vac 8/2/07 744 AM Description fonctionnelle Figure a Directives DE Sécurité Importantes Pour LES BLOCS- Piles Lire Toutes LES DirectivesRecommandations EN Matière DE Rangement Procédure DE ChargeVoyants DE Charge Remplacer le bloc-pilesFonctionnement BLOC-PILES Laissé Dans LE ChargeurRemarques Importantes Pour LE Chargement Pour Maximiser LA Durée DE VIE DE LA PileRetirer le bloc-piles Mise EN Marche ET Arrêt Figure FVoyants DEL DE Pile Figure G Nettoyage FIG. H À MInformation SUR LES Réparations AccessoiresEntretien Cause possible Solution possible Dépannage555326-7100 Recomendaciones Importantes Tenga Especial Precaución al limpiar las escaleras90521333 VPX2102 Hand Vac 8/2/07 744 AM Descripción Funcional Figure a Introducción LEA Todas LAS InstruccionesRecomendaciones CON Respecto AL Almacenamiento Procedimiento DE CargaIndicadores DE Carga Reemplazar el paquetePara Maximizar LA Vida DE LA Batería Dejar EL Paquete DE Baterías EN EL CargadorNotas Importantes Sobre LA Carga Instrucciones DE Operación Encendido Y Apagado Figura FIndicadores LED DE LA Batería Figura G Limpieza DEL Producto Figuras H-MFiltros AccesoriosMantenimiento Información DE MantenimientoGarantía Completa DE DOS Años Para USO EN EL Hogar Detección DE ProblemasProblema Causa posible Solución posible Especificaciones

90521333, VPX2102 specifications

The Black & Decker VPX2102,90521333 is a versatile and powerful tool designed to meet the diverse needs of DIY enthusiasts and professionals alike. With its commitment to user-friendly design and innovative technologies, this product is an essential addition to any toolkit.

One of the standout features of the VPX2102 is its lightweight and compact design. Weighing in at just a few pounds, it offers easy maneuverability, making it ideal for projects that require agility and precision. The compactness also aids in storage, allowing users to keep their workspace organized without sacrificing functionality.

Touching on performance, the VPX2102 boasts a robust motor that delivers exceptional power, enabling it to tackle tough materials with ease. Whether you're drilling through wood, metal, or plastic, the tool ensures smooth operation and efficient results. It is equipped with variable speed settings, allowing users to adjust the speed according to the task at hand, providing enhanced control for both delicate and heavy-duty applications.

In terms of technological advancements, the VPX2102 features an advanced battery management system. This system not only prolongs the battery's lifespan but also optimizes power usage, providing users with longer run times for extended projects. The rechargeable battery can be easily swapped out, ensuring that your workflow remains uninterrupted.

Safety is another priority with the VPX2102. It comes equipped with a built-in safety lock feature that prevents accidental starting, providing peace of mind during transport or storage. Additionally, the ergonomic grip is designed for comfort, reducing hand fatigue during prolonged use, which is particularly important during long projects.

The tool is compatible with a variety of Black & Decker accessories, increasing its versatility. Users can easily switch between bits and attachments, allowing for quick transitions between different tasks. This adaptability makes the VPX2102 a practical choice for those who require a multifunctional tool.

In summary, the Black & Decker VPX2102,90521333 is an impressive tool, enriched with features aimed at enhancing usability and performance. Its combination of powerful operation, portability, advanced battery management, and safety features makes it a valuable asset for any user looking to efficiently tackle a variety of tasks. Whether you are a seasoned professional or a weekend warrior, the VPX2102 stands ready to assist you in achieving your project goals.
Top Page Image Contents