Packing Check List | Billy Goat BG1002SP specs

9GENERAL SAFETY

For your safety and the safety of others, these directions should be followed:

Do not operate this machine without first reading owner's manual and engine manufacturer's manual.

Use of Ear Protection is recommended while operating this machine.

Use of Eye and Breathing protection is recom- mended when using this machine, especially in dry

and dusty conditions. Optional bag cover directs dust toward ground, away from the operator.

·DO NOT place hands or feet inside nozzle intake opening, near debris outlet or near any moving parts.

·DO NOT start engine without debris bag and quick discon- nect connected firmly in place to exhaust outlet.

·DO NOT start or operate machine with debris bag zipper open.

·DO NOT operate during excessive vibration.

·DO NOT remove bag until engine has been turned off and has come to a complete stop.

·DO NOT remove hose kit cap on nozzle until engine has been turned off and has come to a complete stop.

·DO NOT operate machine with hose cap, bag or hose removed. ·DO NOT use this machine for vacuuming exclusively sand, dust, fine dirt, rock, glass, string like material, grain, rags, cans, metal, bark or water.

·DO NOT operate this machine on slopes greater than 20%. ·DO NOT pick up any hot or burning debris, or any toxic or explosive material.

·DO NOT allow children to operate this equipment.

10ASSEMBLY

Read all safety and operating instructions before assembling or starting this unit.

PUT OIL IN ENGINE BEFORE STARTING.

Your Billy Goat is shipped from the factory in one carton, completely assembled except for the debris bag, upper and lower handles, handle brace, nozzle control rods, exhaust elbow, gasket, and (sp only) rod lever shift assy.

1Lower handles: Assemble lower handles (items 60, 61) to engine base using washers (item 17) and lock nuts (item 5).

HANDTIGHTEN ONLY.

2Upper Handle, Handle Braces:

2.1Assemble upper handle (item 47), and handle braces (items95 and 99) to lower handles using screws (item 40), washers (item 17) and lock nuts (item 5) with ends of handle brace on inside of handle and screw heads facing inward, toward debris bag, otherwise premature bag wear could result. HANDTIGHTEN ONLY.

2.2After elbow assembly has been installed, attach front of handle braces

(items 95 and 99) to 3/8 inch stud on elbow mounting flange, using lock nut (item 43).

3.Tighten all handle screws and nuts on lower handles, upper handle and handle

brace.

4. Throttle control (item 52):

4.1Attach throttle to upper handle using screw (item 21) and lock nut (item 18).

4.2Attach throttle control conduit to handles using cable clamps (item 93).

5. Nozzle door control rods (items 55, 59):

5.1Attach end of link (item 59) with single hole to nozzle door mounting hole using screw (item 54), washers (item 17-2 req'd) and lock nut (item 18).

5.2Assemble link (item 55) to lever assembly (item 56) using screws (item 54), washers (item 17-2 req'd) and lock nuts (item 18).

5.3Attach link ends (item 59, 55) to each other in 2 holes using screw (item 21), washers (item 17) and lock nut (item 18).

6.Elbow Assembly (item 2):

Attach elbow assembly (item 2) and flange gasket to exhaust outlet of main unit using screws (item 17) and lock nuts (item 5).

7.Debris Bag (item 1):

7.1Attach neck of debris bag onto elbow assembly.

SECURELY TIGHTEN BAG NECK STRAP.

7.2Attach bag hanger clips to bag loops (item 50) preassembled to upper handle.

8.SP MODEL ONLY. Rod Lever Shift Assy.

8.1Remove eye bolt (item 45), from hardware bag and slide curved end of rod through eye bolt (item 45).

8.2Slide curved end of Rod Lever Shift (item 90) through hole in shift bracket located on rear of transmission so that shift lever end of rod is up. Reinstall eye bolt (item 45) and hardward through upper handle and clutch cable mounting bracket.

9.Attach "z" end of cable (item 86) to inside of bracket on rod bail assy (item 88).

10.Connect spark plug wire.

11PACKING CHECK LIST

These items should be included in your carton. If any of these parts are missing, contact your dealer.

Boxing Checklist

Self Propelled Only

Check		Rod Lever

		810162

Boxing Checklist

Brace Handle LH Check

800821

Brace Handle RH	Check	5
Brace Handle RH
800822

Per Model

Parts Bag & Lit.

Assy.

BG1002	Check
BG1002
800014
BG1002SP	Check
BG1002SP
800015

Engine Manual

Briggs & Stratton

10 HP Intek	Check
10 HP Intek

Part No. 800012

	Denotes parts found in
	Parts Bag Assembly
Page 3 of 12	(shown on page 4).