Desa VML27PR Installing Heater Base Assembly, Installing Optional Remote Control Accessories

Page 10

10

INSTALLATION

Installing Heater Base Assembly

Installing Optional Remote Control Accessories

INSTALLATION

Continued

INSTALLING HEATER BASE ASSEMBLY

CAUTION: Do not remove the data plates attached to the heater base assembly. The data plates contain important warranty and safety information.

WARNING: You must secure this heater to fire- place floor. If not, heater will move when you adjust controls. Moving heater may cause a gas leak.

WARNING: If installing in a sunken fireplace, special care is needed. You must raise the fireplace floor to allow access to heater control panel. This will insure adequate air flow and guard against sooting and con- trols being damaged. Raise fireplace floor with noncom- bustible material. Make sure material is secure.

CAUTION: Do not pick up heater base assembly by the burner. This could damage heater. Only handle base assembly by grates.

IMPORTANT: Make sure the heater burner is level. If heater is not level, heater will not work properly.

8.Remove heater base from fireplace. If installing optional con- trol accessories, do so at this time. Follow all directions pro- vided with accessory. See Installing Optional Remote Control Accessories, below.

9.Drill holes at marked locations using 3/16" drill bit.

10.Attach base assembly to fireplace floor using two masonry screws (in hardware package).

Flexible Gas Hose (if allowed by local

codes)

Fitting

Figure 11 - Attaching Flexible Gas Hose to Heater

Masonry Screw

Mounting

Flange

Figure 12 - Attaching Base Assembly to Fireplace Floor

Installation Items Needed

•hardware package (provided with heater)

•approved flexible gas hose (not provided) (if allowed by local codes)

•sealant (resistant to propane/LP gas, not provided)

•electric drill with 3/16" drill bit (metal or masonry as applicable)

•flathead screwdriver

1.Apply pipe joint sealant lightly to male threads of the fitting to be threaded into gas control. Connect approved flexible gas hose to gas control fitting in heater (see Figure 11). IMPORTANT: Hold gas fitting with wrench when connecting flexible gas hose.

2.Locate two masonry screws in hardware package.

3.Place heater base in fireplace.

4.Place logs in their proper position on heater base. See Install- ing Logs, pages 13 and 14.

5.Center heater base and logs front-to-back and side-to-side in fireplace.

6.Carefully remove logs without moving heater base.

7.Mark screw locations through one hole on each side of the mounting bracket (see Figure 12). If installing in a brick-bot- tom fireplace, mark screw locations in mortar joint of bricks.

INSTALLING OPTIONAL REMOTE CONTROL ACCESSORIES

Installing Remote Receiver

All remote control accessories are available separately (see Acces- sories, page 27). The remote receiver for these accessories will be installed using the bracket located on the front left side of the base.

1.Disconnect jumper wire from control valve at TPTH and TH locations (see Figure 13),

2, Install remote receiver into receiver bracket using push button clips provided with receiver (see Figure 14, page 11).

3.Connect wires to control valve at the TPTH and TH locations as shown in Figure 15, page 11.

Jumper Wire

Control

Valve

Figure 13 - Disconnecting Jumper Wire from Control Valve

For morevisit www..com

111115-01D

Page 9 Page 11
Image 10
Page 9 Page 11
Contents VML27NR VML27PR Remote Control Ready Model Patent PendingFLAME-MAX What to do if YOU Smell GASTable of Contents Safety InformationProduct Identification Local CodesUnpacking Product FeaturesRemote Control Accessories AIR for Combustion and VentilationConfined and Unconfined Space Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Uncon- fined Space Ventilation Air From Inside Building InstallationVentilation AIR Ventilation Air From OutdoorsLOG Sizing Requirements Installation and ClearancesMinimum Fireplace Clearance to Combustible Materials Check GAS TypeMinimum Noncombustible Material Clearances Determining Minimum Mantel Clearance When using a HoodMantel Clearances Determining Minimum Mantel ClearanceInstalling Damper Clamp Accessory for Vented Operation Floor ClearancesInstallation Items Needed Installing Heater Base AssemblyInstalling Optional Remote Control Accessories Installing Remote ReceiverConnecting to GAS Supply Installing 9-Volt Battery in ReceiverPressure Testing Gas Supply Piping System Checking GAS ConnectionsPressure Testing Heater Gas Connections Installing LogsProperty damage or personal injury For Your Safety Read Before Lighting Operating HeaterLighting Instructions Control Knob and Ignitor Button LocationOptional HAND-HELD Remote Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance ON/OFF Series Model GhrcbBurner Primary AIR Holes Inspecting BurnersPilot Flame Pattern Main BurnerCleaning Burner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceWiring Diagram LogsTroubleshooting Observed Problem Possible CauseObserved Problem Possible Cause Remedy Gas leak. See Warning statement at TopIllustrated Parts Breakdown Models VML27PR VML27NRParts List KEY Part Number VML27PR VML27NR Description QTYTechnical Service Replacement Parts SpecificationsService Hints Parts Under WarrantyOwners Registration Form Postage Required Cleaning KIT GCK WALL-MOUNT Thermostat Switch GWMT1WALL-MOUNT ON/OFF Switch GWMS2 Receiver and HAND-HELD Remote CON Trol KIT GhrcbWarranty Information

VML27PR specifications

Desa VML27PR is a cutting-edge development that represents a significant leap forward in efficient living and sustainable technology. This modern residential complex is designed with both aesthetics and functionality in mind, making it a prime choice for contemporary urban dwellers.

One of the standout features of Desa VML27PR is its commitment to energy efficiency. The buildings are equipped with solar panels that harness renewable energy, significantly reducing reliance on non-renewable power sources. This integration not only lowers utility bills for residents but also contributes to a lower carbon footprint, aligning with global sustainable development goals.

The architecture of Desa VML27PR is marked by its contemporary design, featuring open floor plans and large windows that maximize natural light and ventilation. The use of eco-friendly construction materials further enhances the sustainability aspect, ensuring that the development minimizes its impact on the environment while providing a comfortable living space.

Safety and security are of paramount importance in Desa VML27PR. The complex is equipped with state-of-the-art security systems, including video surveillance and controlled access points, giving residents peace of mind. Additionally, the premises are well-lit and feature landscaped green spaces, promoting a sense of community while ensuring a safe environment for families.

Another significant characteristic of Desa VML27PR is its emphasis on smart technology integration. Homes are equipped with smart appliances and systems that allow residents to control lighting, heating, and security from their mobile devices. This not only enhances convenience but also promotes energy savings by enabling users to monitor and manage their usage effectively.

Desa VML27PR also boasts a variety of communal facilities designed to foster community engagement. These include recreational areas, fitness centers, and coworking spaces that encourage interaction among residents, making it an ideal place for those seeking a vibrant social life.

In conclusion, Desa VML27PR exemplifies the future of urban living, combining sustainability, modern design, advanced technology, and community-focused amenities. It stands as a model for future residential developments, showcasing how contemporary living can harmoniously coexist with environmental responsibility and community engagement. Whether seeking a home for a growing family or a sophisticated living space for professionals, Desa VML27PR is equipped to meet diverse needs, making it a premier choice in today’s real estate market.
Top Page Image Contents