Desa VML27PR installation manual Cleaning Maintenance, Wiring Diagram, Logs

Page 18

18

CLEANING AND MAINTENANCE

Cleaning Burner Injector Holder And Pilot Air Inlet Hole Logs

WIRING DIAGRAM

CLEANING AND

MAINTENANCE

WARNING: Turn off heater and let cool before cleaning.

CAUTION: You must keep control areas, burner, and circulating air passageways of heater clean. In- spect these areas of heater before each use. Have heater inspected yearly by a qualified service person. Heater may need more frequent cleaning due to exces- sive lint from carpeting, bedding material, pet hair, etc.

WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in soot- ing and property damage.

CLEANING BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLE

The primary air inlet holes allow the proper amount of air to mix with the gas. This provides a clean burning flame. Keep these holes clear of dust, dirt, lint, and pet hair. Clean these air inlet holes prior to each heating season. Blocked air holes will create soot. We recommend that you clean the unit every three months during operation and have heater inspected yearly by a qualified service person.

We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSI. Your local computer store, hardware store, or home center may carry com- pressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the direc- tions on the can. If you don't follow directions on the can, you could damage the pilot assembly.

1.Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.

2.Inspect burner, pilot, and primary air inlet holes on injector holder for dust and dirt (see Figure 36).

3.Blow air through the ports/slots and holes in the burner.

4.Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint, or pet hair with a soft cloth or vacuum cleaner nozzle.

5.Blow air into the primary air holes on the injector holder.

6.In case any large clumps of dust have now been pushed into the burner repeat steps 3 and 4.

Clean the pilot assembly also. A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see Figure 37). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.

Burner

Tube

Injector Holder

Primary Air Inlet Holes (Shape of Holes May

Vary by Model)

Figure 36 - Injector Holder On Outlet Burner Tube

Ports/Slots

Burner Tube

Pilot Assembly

Pilot Air

Inlet Hole

Figure 37 - Pilot Inlet Air Hole

LOGS

•If you remove logs for cleaning, refer to Installing Logs, pages 13 and 14, to properly replace logs.

•Replace log(s) if broken or chipped (dime-sized or larger).

WIRING DIAGRAM

Jumper Wire

Thermopile

For morevisit www..com

111115-01D

Page 17 Page 19
Image 18
Page 17 Page 19
Contents VML27NR VML27PR Remote Control Ready Model Patent PendingFLAME-MAX What to do if YOU Smell GASTable of Contents Safety InformationProduct Identification Local CodesUnpacking Product FeaturesRemote Control Accessories AIR for Combustion and VentilationDetermining FRESH-AIR Flow for Heater Location Confined and Unconfined SpaceDetermining if You Have a Confined or Uncon- fined Space Ventilation Air From Inside Building InstallationVentilation AIR Ventilation Air From OutdoorsLOG Sizing Requirements Installation and ClearancesMinimum Fireplace Clearance to Combustible Materials Check GAS TypeMinimum Noncombustible Material Clearances Determining Minimum Mantel Clearance When using a HoodMantel Clearances Determining Minimum Mantel ClearanceInstalling Damper Clamp Accessory for Vented Operation Floor ClearancesInstallation Items Needed Installing Heater Base AssemblyInstalling Optional Remote Control Accessories Installing Remote ReceiverConnecting to GAS Supply Installing 9-Volt Battery in ReceiverPressure Testing Gas Supply Piping System Checking GAS ConnectionsInstalling Logs Pressure Testing Heater Gas ConnectionsProperty damage or personal injury For Your Safety Read Before Lighting Operating HeaterLighting Instructions Control Knob and Ignitor Button LocationOptional HAND-HELD Remote Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance ON/OFF Series Model GhrcbBurner Primary AIR Holes Inspecting BurnersPilot Flame Pattern Main BurnerCleaning Burner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceWiring Diagram LogsTroubleshooting Observed Problem Possible CauseObserved Problem Possible Cause Remedy Gas leak. See Warning statement at TopIllustrated Parts Breakdown Models VML27PR VML27NRParts List KEY Part Number VML27PR VML27NR Description QTYTechnical Service Replacement Parts SpecificationsService Hints Parts Under WarrantyOwners Registration Form Postage Required Cleaning KIT GCK WALL-MOUNT Thermostat Switch GWMT1WALL-MOUNT ON/OFF Switch GWMS2 Receiver and HAND-HELD Remote CON Trol KIT GhrcbWarranty Information

VML27PR specifications

Desa VML27PR is a cutting-edge development that represents a significant leap forward in efficient living and sustainable technology. This modern residential complex is designed with both aesthetics and functionality in mind, making it a prime choice for contemporary urban dwellers.

One of the standout features of Desa VML27PR is its commitment to energy efficiency. The buildings are equipped with solar panels that harness renewable energy, significantly reducing reliance on non-renewable power sources. This integration not only lowers utility bills for residents but also contributes to a lower carbon footprint, aligning with global sustainable development goals.

The architecture of Desa VML27PR is marked by its contemporary design, featuring open floor plans and large windows that maximize natural light and ventilation. The use of eco-friendly construction materials further enhances the sustainability aspect, ensuring that the development minimizes its impact on the environment while providing a comfortable living space.

Safety and security are of paramount importance in Desa VML27PR. The complex is equipped with state-of-the-art security systems, including video surveillance and controlled access points, giving residents peace of mind. Additionally, the premises are well-lit and feature landscaped green spaces, promoting a sense of community while ensuring a safe environment for families.

Another significant characteristic of Desa VML27PR is its emphasis on smart technology integration. Homes are equipped with smart appliances and systems that allow residents to control lighting, heating, and security from their mobile devices. This not only enhances convenience but also promotes energy savings by enabling users to monitor and manage their usage effectively.

Desa VML27PR also boasts a variety of communal facilities designed to foster community engagement. These include recreational areas, fitness centers, and coworking spaces that encourage interaction among residents, making it an ideal place for those seeking a vibrant social life.

In conclusion, Desa VML27PR exemplifies the future of urban living, combining sustainability, modern design, advanced technology, and community-focused amenities. It stands as a model for future residential developments, showcasing how contemporary living can harmoniously coexist with environmental responsibility and community engagement. Whether seeking a home for a growing family or a sophisticated living space for professionals, Desa VML27PR is equipped to meet diverse needs, making it a premier choice in today’s real estate market.
Top Page Image Contents