Desa VML27NR Installing Heater Base Assembly, Installing Optional Remote Control Accessories

Page 10

10

INSTALLATION

Installing Heater Base Assembly

Installing Optional Remote Control Accessories

INSTALLATION

Continued

INSTALLING HEATER BASE ASSEMBLY

CAUTION: Do not remove the data plates attached to the heater base assembly. The data plates contain important warranty and safety information.

WARNING: You must secure this heater to fire- place floor. If not, heater will move when you adjust controls. Moving heater may cause a gas leak.

WARNING: If installing in a sunken fireplace, special care is needed. You must raise the fireplace floor to allow access to heater control panel. This will insure adequate air flow and guard against sooting. Raise fireplace floor with noncombustible material. Make sure material is secure.

CAUTION: Do not pick up heater base assembly by the burner. This could damage heater. Only handle base assembly by grates.

IMPORTANT: Make sure the heater burner is level. If heater is not level, heater will not work properly.

8.Remove heater base from fireplace. If installing optional con- trol accessories, do so at this time. Follow all directions pro- vided with accessory. See Installing Optional Remote Control Accessories, below.

9.Drill holes at marked locations using 3/16" drill bit.

10.Attach base assembly to fireplace floor using two masonry screws (in hardware package).

 

Flexible Gas Hose

 

(if allowed by local

Fitting

codes)

 

Figure 11 - Attaching Flexible Gas Hose to Heater

Masonry Screw

Mounting

Flange

Figure 12 - Attaching Base Assembly to Fireplace Floor

Installation Items Needed

•hardware package (provided with heater)

•approved flexible gas hose (not provided) (if allowed by local codes)

•sealant (resistant to propane/LP gas, not provided)

•electric drill with 3/16" drill bit (metal or masonry as applicable)

•flathead screwdriver

1.Apply pipe joint sealant lightly to male threads of the fitting to be threaded into gas control. Connect approved flexible gas hose to gas control fitting in heater (see Figure 11). IMPORTANT: Hold gas fitting with wrench when connecting flexible gas hose.

2.Locate two masonry screws in hardware package.

3.Place heater base in fireplace.

4.Place logs in their proper position on heater base. See Install- ing Logs, pages 13 and 14.

5.Center heater base and logs front-to-back and side-to-side in fireplace.

6.Carefully remove logs without moving heater base.

7.Mark screw locations through one hole on each side of the mounting bracket (see Figure 12). If installing in a brick-bot- tom fireplace, mark screw locations in mortar joint of bricks.

INSTALLING OPTIONAL REMOTE CONTROL ACCESSORIES

Installing Remote Receiver

All remote control accessories are available separately (see Acces- sories, page 27). The remote receiver for these accessories will be installed using the bracket located on the front left side of the base.

1.Disconnect jumper wire from control valve at TPTH and TH locations (see Figure 13),

2, Install remote receiver into receiver bracket using push button clips provided with receiver (see Figure 14, page 11).

3.Connect wires to control valve at the TPTH and TH locations as shown in Figure 15, page 11.

Jumper

Wire

Control

Valve

Figure 13 - Disconnecting Jumper Wire from Control Valve

For morevisit www..com

111115-01A

Page 9 Page 11
Image 10
Page 9 Page 11
Contents VML27NR VML27PR Remote Control Ready Model Patent PendingFLAME-MAX What to do if YOU Smell GASTable of Contents Safety InformationProduct Identification Local CodesUnpacking Product FeaturesRemote Control Accessories AIR for Combustion and VentilationConfined and Unconfined Space Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Uncon- fined Space Ventilation Air From Inside Building InstallationVentilation AIR Ventilation Air From OutdoorsLOG Sizing Requirements Installation and ClearancesMinimum Fireplace Clearance to Combustible Materials Check GAS TypeMinimum Noncombustible Material Clearances Determining Minimum Mantel Clearance When using a HoodMantel Clearances Determining Minimum Mantel ClearanceInstalling Damper Clamp Accessory for Vented Operation Floor ClearancesInstallation Items Needed Installing Heater Base AssemblyInstalling Optional Remote Control Accessories Installing Remote ReceiverConnecting to GAS Supply Installing 9-Volt Battery in ReceiverPressure Testing Gas Supply Piping System Checking GAS ConnectionsPressure Testing Heater Gas Connections Installing LogsProperty damage or personal injury For Your Safety Read Before Lighting Operating HeaterLighting Instructions Control Knob and Ignitor Button LocationTo Turn OFF GAS To Appliance Manual Lighting ProcedureOptional Remote Operation Burner Primary AIR Holes Inspecting BurnersPilot Flame Pattern Main BurnerCleaning Burner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceWiring Diagram LogsTroubleshooting Observed Problem Possible CauseObserved Problem Possible Cause Remedy Gas leak. See Warning statement at TopIllustrated Parts Breakdown VML27PR VML27NRParts List KEY Part Number VML27PR VML27NR Description QTYTechnical Service Replacement Parts SpecificationsService Hints Parts Under WarrantyOwners Registration Form Postage Required WALL-MOUNT ON/OFF Switch GWMS2 Receiver and HAND-HELD Remote Control KIT GhrcWALL-MOUNT Thermostat Switch GWMT1 Cleaning KIT GCKWarranty Information

VML27NR specifications

Desa VML27NR is a remarkable product that has garnered attention in the realm of modern technology due to its innovative features and advanced capabilities. Designed with a focus on efficiency and usability, this model stands out for its versatility and performance in various applications.

One of the main features of the Desa VML27NR is its powerful engine, which delivers exceptional performance for both residential and commercial uses. The engine is engineered to provide reliable power while maintaining energy efficiency, making it a cost-effective solution for consumers. Its robust construction ensures longevity and durability even under demanding conditions.

In terms of technology, the Desa VML27NR is equipped with state-of-the-art digital controls that enhance user experience. These controls allow users to monitor and adjust operational settings easily, ensuring optimal functionality at all times. Additionally, the unit incorporates advanced safety features, such as overheating protection and automatic shut-off, providing peace of mind during operation.

Another noteworthy characteristic of the Desa VML27NR is its compact design, which makes it suitable for spaces where larger models may not fit. Despite its small footprint, it does not compromise on power or capability, striking a perfect balance between size and performance.

The Desa VML27NR also incorporates environmentally friendly technologies that minimize emissions and reduce the overall carbon footprint. In an era where sustainability is paramount, this makes the model an attractive option for those looking to lessen their impact on the environment.

Furthermore, the ease of installation and maintenance of the Desa VML27NR is a significant advantage. Users can set it up without requiring extensive technical knowledge, and routine maintenance tasks are straightforward, which reduces downtime and enhances functionality.

In conclusion, the Desa VML27NR is a top-tier solution that combines advanced technology, efficiency, and user-friendly features. Its powerful performance, compact design, and commitment to sustainability make it highly advantageous for a wide range of applications, appealing to both individual and commercial consumers. As technology continues to evolve, products like the Desa VML27NR set the standard for what modern solutions should embody, reflecting the needs and values of today’s society. Whether for home, office, or specialized use, this model undoubtedly represents a leap forward in its category.
Top Page Image Contents