Desa VML27NR To Turn OFF GAS To Appliance, Manual Lighting Procedure, Optional Remote Operation

Page 16

16

OPERATING HEATER

To Turn Off Gas To Appliance

Manual Lighting Procedure

Optional Remote Operation

OPERATING HEATER

Continued

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

1.Remove control cover log (see Figure 28, page 15).

2.Turn control knob clockwise to the OFF position.

3.If Using Optional Hand-Held Remote: Let unit cool. Remove all logs from base and set remote sensor selector switch to the OFF position.

4.Replace control cover log ( or all logs if removed in step 3). See Installing Logs, pages 13 and 14.

Shutting Off Burner Only (pilot stays lit)

You may shut off the burner and keep the pilot lit by doing one of the following:

Thermostat Control Operation

(Optional GHRCTA Series Only) The thermostat control set- ting on the remote control unit can be set to any comfort level between WARMER and COOLER. The burner will turn on and off automatically to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc.

For wall thermostat operation, follow instructions supplied with thermostat accessory GWMT1. For wall switch operation follow instructions supplied with GWMS2.

NOTICE: You must light the pilot before using the hand-held remote control unit. See Lighting Instruc- tions on page 15.

1.Remove control cover log (see Figure 28, page 15). Turn

control knob clockwise to the PILOT position. Re- place control cover log.

2.If Using Optional Hand-Held Remote: Use remote control manual OFF button.

WARNING: Make sure remote sensor selector switch is in the OFF position when you are away from home for long periods of time. Follow step 3 under Shutting Off Heater.

Piezo Ignitor

ON

OFF

REMOTE

Selector Switch in Remote Position (Optional Remote Control)

Flame Adjustment Knob

IH

 

F

PIL

 

 

O

 

O

F

T

 

 

 

 

O

 

 

 

 

 

 

N

LO

 

 

 

Control Knob in On Position

MANUAL LIGHTING

PROCEDURE

1.Follow steps 1 through 6 under Lighting Instructions, page 15.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow steps 9 through 11, page 15.

OPTIONAL REMOTE

OPERATION

Note: All remote control accessories must be purchased sepa- rately (see Accessories, page 27). Follow instructions included with the remote control.

Figure 31 - Setting the Selector Switch, Control Knob, and Flame Adjustment Knob for Remote Operation

1.After lighting, let pilot flame burn for about one minute. Carefully remove logs. Slide sensor selector switch to the REMOTE position. NOTE: The burner may light if hand- held remote ON button was on when selector switch was last turned off. Carefully replace logs except for control cover log (see Installing Logs, pages 13 and 14). Turn con- trol knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Replace control cover log. You can now turn the burner on and off with the hand- held remote control unit.

IMPORTANT: Do not leave the selector switch in the RE- MOTE position when the pilot is not lit. This will drain the battery.

IMPORTANT: Be sure to press the ON/OFF buttons on the hand held remote control unit for up to 3 seconds to assure proper operation.

For morevisit www..com

111115-01A

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Remote Control Ready Model Patent Pending FLAME-MAXVML27NR VML27PR What to do if YOU Smell GASTable of Contents Safety InformationProduct Identification Local CodesProduct Features Remote Control AccessoriesUnpacking AIR for Combustion and VentilationConfined and Unconfined Space Determining FRESH-AIR Flow for Heater LocationDetermining if You Have a Confined or Uncon- fined Space Installation Ventilation AIRVentilation Air From Inside Building Ventilation Air From OutdoorsInstallation and Clearances Minimum Fireplace Clearance to Combustible MaterialsLOG Sizing Requirements Check GAS TypeDetermining Minimum Mantel Clearance When using a Hood Mantel ClearancesMinimum Noncombustible Material Clearances Determining Minimum Mantel ClearanceInstalling Damper Clamp Accessory for Vented Operation Floor ClearancesInstalling Heater Base Assembly Installing Optional Remote Control AccessoriesInstallation Items Needed Installing Remote ReceiverConnecting to GAS Supply Installing 9-Volt Battery in ReceiverPressure Testing Gas Supply Piping System Checking GAS ConnectionsPressure Testing Heater Gas Connections Installing LogsProperty damage or personal injury For Your Safety Read Before Lighting Operating HeaterLighting Instructions Control Knob and Ignitor Button LocationTo Turn OFF GAS To Appliance Manual Lighting ProcedureOptional Remote Operation Inspecting Burners Pilot Flame PatternBurner Primary AIR Holes Main BurnerCleaning Maintenance Wiring DiagramCleaning Burner Injector Holder and Pilot AIR Inlet Hole LogsTroubleshooting Observed Problem Possible CauseObserved Problem Possible Cause Remedy Gas leak. See Warning statement at TopIllustrated Parts Breakdown VML27PR VML27NRParts List KEY Part Number VML27PR VML27NR Description QTYSpecifications Service HintsTechnical Service Replacement Parts Parts Under WarrantyOwners Registration Form Postage Required Receiver and HAND-HELD Remote Control KIT Ghrc WALL-MOUNT Thermostat Switch GWMT1WALL-MOUNT ON/OFF Switch GWMS2 Cleaning KIT GCKWarranty Information

VML27NR specifications

Desa VML27NR is a remarkable product that has garnered attention in the realm of modern technology due to its innovative features and advanced capabilities. Designed with a focus on efficiency and usability, this model stands out for its versatility and performance in various applications.

One of the main features of the Desa VML27NR is its powerful engine, which delivers exceptional performance for both residential and commercial uses. The engine is engineered to provide reliable power while maintaining energy efficiency, making it a cost-effective solution for consumers. Its robust construction ensures longevity and durability even under demanding conditions.

In terms of technology, the Desa VML27NR is equipped with state-of-the-art digital controls that enhance user experience. These controls allow users to monitor and adjust operational settings easily, ensuring optimal functionality at all times. Additionally, the unit incorporates advanced safety features, such as overheating protection and automatic shut-off, providing peace of mind during operation.

Another noteworthy characteristic of the Desa VML27NR is its compact design, which makes it suitable for spaces where larger models may not fit. Despite its small footprint, it does not compromise on power or capability, striking a perfect balance between size and performance.

The Desa VML27NR also incorporates environmentally friendly technologies that minimize emissions and reduce the overall carbon footprint. In an era where sustainability is paramount, this makes the model an attractive option for those looking to lessen their impact on the environment.

Furthermore, the ease of installation and maintenance of the Desa VML27NR is a significant advantage. Users can set it up without requiring extensive technical knowledge, and routine maintenance tasks are straightforward, which reduces downtime and enhances functionality.

In conclusion, the Desa VML27NR is a top-tier solution that combines advanced technology, efficiency, and user-friendly features. Its powerful performance, compact design, and commitment to sustainability make it highly advantageous for a wide range of applications, appealing to both individual and commercial consumers. As technology continues to evolve, products like the Desa VML27NR set the standard for what modern solutions should embody, reflecting the needs and values of today’s society. Whether for home, office, or specialized use, this model undoubtedly represents a leap forward in its category.
Top Page Image Contents