Desa REM10PT RH10PT installation manual To Turn OFF GAS To Appliance, Thermostat Control Operation

Page 10

10

OPERATING HEATER

Lighting Instructions

To Turn Off Gas To Appliance

Thermostat Control Operation

Manual Lighting Procedure

OPERATING HEATER

Continued

6.With control knob pressed in, push down and release igni- tor button. This will light pilot. The pilot is attached to the front of burner. The pilot can be seen through the glass panel. If needed, keep pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, refer to Troubleshooting, pages 13 through 15. Also contact a qualified service per- son or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure.

7.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

•If control knob does not pop up when released, contact a qualified service person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 3 through 7. This heater has a safety interlock system. Wait one (1) minute before lighting pilot again.

8.Turn control knob counterclockwise to desired heating level. The main burner should light. Set control knob to any heat level between HI and LO.

CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve.

Ignitor Button

Control Knob

 

PILOT

LO

 

 

 

FFO

 

 

IH

 

IGNITOR

 

 

Figure 16 - Control Knob In The OFF Position

Thermocouple

Ignitor Electrode

Pilot Burner

Figure 17 - Pilot

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

1.Turn control knob clockwise to the OFF position.

2.Turn off all electric power to the appliance if service is to be performed.

Shutting Off Burner Only (pilot stays lit)

Turn control knob clockwise to the PILOT position.

THERMOSTAT CONTROL

OPERATION

The thermostatic control used on these models differs from stan- dard thermostats. Standard thermostats simply turn on and off the burner. The thermostat used on this heater senses the room temperature. The thermostat adjusts the amount of gas flow to the burner. This increases or decreases the burner flame height. At times the room may exceed the set temperature. If so, the burner will shut off. The burner will cycle back on when room temperature drops below the set temperature. The control knob can be set to any heat level between HI and LO. Selecting the HI setting will cause the burner to remain fully on without modulating down in most cases.

Note: The thermostat sensing bulb measures the temperature of air near the heater cabinet. This may not always agree with room temperature (depending on housing construction, instal- lation location, room size, open air temperatures, etc.). Fre- quent use of your heater will let you determine your own comfort levels.

MANUAL LIGHTING

PROCEDURE

1.Remove front panel (see Figure 8, page 5).

2.Follow steps 1 through 5 under Lighting Instructions, page 9.

3.With control knob pressed in, strike match. Hold match to pilot until pilot lights.

4.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Follow step 8 under Lighting Instructions.

5.Replace front panel.

For..com

110373-01D

Page 9 Page 11
Image 10
Page 9 Page 11
Contents REM10PT RH10PT Blue Flame VENT-FREE PROPANE/LP GAS HeaterWhat to do if YOU Smell GAS Table of Contents Safety InformationProduct Identification UnpackingLocal Codes Product FeaturesInstallation PROPANE/LP SupplyInstalling Heater to Wall Thermostat Sensing BulbConnecting to Portable Cylinder GAS Supply Installing Bottom Mounting ScrewConnecting to Permanent GAS Supply Installation ItemsPressure Testing Gas Supply Piping System Permanent GAS SupplyOperating Heater For Your Safety Read Before LightingPressure Testing Heater Gas Connections Checking GAS Connections for Permanent GAS SupplyThermostat Control Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off HeaterPilot Flame Pattern Inspecting BurnerStorage Burner Flame PatternODS/PILOT and Burner Cleaning MaintenanceCleaning Burner Pilot AIR Inlet CabinetTroubleshooting Observed Problem Possible Cause RemedyMaintenance, Gas leak. See Warning statement at Illustrated Parts Breakdown Models REM10PT RH10PT PilotParts List KEY Part Number REM10PT RH10PT Description QTYService Hints SpecificationsTechnical Service Service Publications AccessoriesOwners Registration Form Postage Required 110373-01D Warranty Information

REM10PT RH10PT specifications

Desa REM10PT RH10PT is a cutting-edge device that exemplifies innovative engineering in the domain of environmental monitoring and management. Designed to address the increasing demand for smart technology in both urban and rural settings, the REM10PT RH10PT integrates a range of advanced features that allow users to effectively monitor and control their environments.

One of the standout attributes of the REM10PT RH10PT is its exceptional sensor technology. Equipped with high-precision sensors, this device can accurately measure a variety of environmental parameters, including temperature, humidity, air quality, and other critical factors. The real-time data collection ensures that users are kept informed about their surroundings, enabling them to make timely and informed decisions.

The REM10PT RH10PT also boasts a robust connectivity framework. It supports various communication protocols such as Wi-Fi, Bluetooth, and Zigbee, facilitating seamless integration with existing home automation systems. This connectivity allows users to access and manage their devices remotely through a dedicated mobile application, providing convenience and flexibility in monitoring environmental conditions.

Another notable feature of this device is its energy-efficient design. The REM10PT RH10PT is built with sustainability in mind, utilizing low-power components that minimize energy consumption without compromising performance. This not only reduces operational costs but also aligns with the global push for greener technologies.

The user interface is intuitive and user-friendly, offering easy navigation through the device's features and settings. It provides customizable alerts and notifications, allowing users to set parameters according to their specific needs. Whether it’s a simple reminder about humidity levels for plant care or urgent alerts regarding air quality fluctuations, the REM10PT RH10PT delivers pertinent information in real-time.

Lastly, the durability of the REM10PT RH10PT deserves praise. Engineered to withstand varying environmental conditions, the device features weather-resistant housing and high-quality materials that ensure longevity and reliability. This makes it suitable for both indoor applications and outdoor settings, including gardens, farms, and industrial environments.

In summary, the Desa REM10PT RH10PT is an innovative environmental monitoring solution that combines high-precision sensors, robust connectivity, energy efficiency, and user-friendly design. Its versatility and durability make it an essential tool for anyone looking to enhance their awareness and control of environmental conditions. As technology continues to evolve, devices like the REM10PT RH10PT pave the way for a smarter, more connected future.
Top Page Image Contents