Desa REM10PT RH10PT Permanent GAS Supply, Pressure Testing Gas Supply Piping System

Page 8

8

INSTALLATION

Connecting To Permanent Gas Supply (Cont.) Checking Gas Connections For Permanent Gas Supply

INSTALLATION

Continued

CONNECTING TO PERMANENT GAS SUPPLY

CHECKING GAS CONNECTIONS FOR

(CONTINUED)

PERMANENT GAS SUPPLY

Install sediment trap in supply line as shown in Figure 13. Locate sediment trap where it is within reach for cleaning. Locate sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly.

IMPORTANT: Hold the pressure regulator with wrench when connecting it to gas piping and/or fittings. Do not over tighten pipe connection to regulator. The regulator body could be damaged.

3/8" NPT

Pressure

Regulator

Pipe Nipple**

 

 

Ground

Heater

Joint

Cabinet

Union

Tee Joint

 

Equipment Shutoff

 

Reducer

 

Valve *

Test

Bushing to

 

From External

1/8" NPT

Gauge

Regulator

1/8" NPT

Connection*

(11" W.C. to

Plug Tap

 

14" W.C.

Tee Joint

 

Pressure)

Sediment

3" Minimum

Pipe Nipple

 

Cap

Trap

 

 

Figure 13 - Gas Connection

 

 

*A CSA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA design-certified equipment shutoff valve from your dealer. See Accessories, page 18.

**The 90º elbow on the regulator is removed and the 3/8" NPT pipe nipple is installed in its place.

WARNING: Test all gas piping and connections, internal and external to unit, for leaks after installing or servicing. Correct all leaks at once.

WARNING: Never use an open flame to check for a leak. Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. Correct all leaks at once.

CAUTION: Make sure external regulator has been installed between propane/LP supply and heater. See guidelines under Connecting to Permanent Gas Sup- ply, pages 7 and 8.

Pressure Testing Gas Supply Piping System

Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)

1.Disconnect appliance with its appliance main gas valve (con- trol valve) and equipment shutoff valve from gas supply pip- ing system. Pressures in excess of 1/2 psig will damage heater regulator.

2.Cap off open end of gas pipe where equipment shutoff valve was connected.

3.Pressurize supply piping system by opening propane/LP supply tank valve or using compressed air.

4.Check all joints of gas supply piping system. Apply a noncor- rosive leak detection fluid to all joints. Bubbles forming show a leak.

5.Correct all leaks at once.

6.Reconnect heater and equipment shutoff valve to gas supply. Check reconnected fittings for leaks.

Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)

1.Close equipment shutoff valve (see Figure 14).

2.Pressurize supply piping system by either opening propane/LP supply tank valve or using compressed air.

Open

Equipment

Shutoff

Valve

Closed

Figure 14 - Equipment Shutoff Valve

For..com

110373-01D

Page 7 Page 9
Image 8
Page 7 Page 9
Contents What to do if YOU Smell GAS Blue Flame VENT-FREE PROPANE/LP GAS HeaterREM10PT RH10PT Table of Contents Safety InformationProduct Identification UnpackingProduct Features InstallationLocal Codes PROPANE/LP SupplyInstalling Heater to Wall Thermostat Sensing BulbConnecting to Portable Cylinder GAS Supply Installing Bottom Mounting ScrewConnecting to Permanent GAS Supply Installation ItemsPressure Testing Gas Supply Piping System Permanent GAS SupplyFor Your Safety Read Before Lighting Pressure Testing Heater Gas ConnectionsOperating Heater Checking GAS Connections for Permanent GAS SupplyManual Lighting Procedure To Turn OFF GAS To ApplianceThermostat Control Operation Shutting Off HeaterInspecting Burner StoragePilot Flame Pattern Burner Flame PatternCleaning Maintenance Cleaning Burner Pilot AIR InletODS/PILOT and Burner CabinetTroubleshooting Observed Problem Possible Cause RemedyMaintenance, Gas leak. See Warning statement at Illustrated Parts Breakdown Models REM10PT RH10PT PilotParts List KEY Part Number REM10PT RH10PT Description QTYSpecifications Technical ServiceService Hints Service Publications AccessoriesOwners Registration Form Postage Required 110373-01D Warranty Information

REM10PT RH10PT specifications

Desa REM10PT RH10PT is a cutting-edge device that exemplifies innovative engineering in the domain of environmental monitoring and management. Designed to address the increasing demand for smart technology in both urban and rural settings, the REM10PT RH10PT integrates a range of advanced features that allow users to effectively monitor and control their environments.

One of the standout attributes of the REM10PT RH10PT is its exceptional sensor technology. Equipped with high-precision sensors, this device can accurately measure a variety of environmental parameters, including temperature, humidity, air quality, and other critical factors. The real-time data collection ensures that users are kept informed about their surroundings, enabling them to make timely and informed decisions.

The REM10PT RH10PT also boasts a robust connectivity framework. It supports various communication protocols such as Wi-Fi, Bluetooth, and Zigbee, facilitating seamless integration with existing home automation systems. This connectivity allows users to access and manage their devices remotely through a dedicated mobile application, providing convenience and flexibility in monitoring environmental conditions.

Another notable feature of this device is its energy-efficient design. The REM10PT RH10PT is built with sustainability in mind, utilizing low-power components that minimize energy consumption without compromising performance. This not only reduces operational costs but also aligns with the global push for greener technologies.

The user interface is intuitive and user-friendly, offering easy navigation through the device's features and settings. It provides customizable alerts and notifications, allowing users to set parameters according to their specific needs. Whether it’s a simple reminder about humidity levels for plant care or urgent alerts regarding air quality fluctuations, the REM10PT RH10PT delivers pertinent information in real-time.

Lastly, the durability of the REM10PT RH10PT deserves praise. Engineered to withstand varying environmental conditions, the device features weather-resistant housing and high-quality materials that ensure longevity and reliability. This makes it suitable for both indoor applications and outdoor settings, including gardens, farms, and industrial environments.

In summary, the Desa REM10PT RH10PT is an innovative environmental monitoring solution that combines high-precision sensors, robust connectivity, energy efficiency, and user-friendly design. Its versatility and durability make it an essential tool for anyone looking to enhance their awareness and control of environmental conditions. As technology continues to evolve, devices like the REM10PT RH10PT pave the way for a smarter, more connected future.
Top Page Image Contents