Thermostat Sensing Bulb

INSTALLATION

Thermostat Sensing Bulb Installing Heater To Wall

INSTALLATION

Continued

The thermostat sensing bulb is located inside the heater. Do not move this bulb during installation or operation of the heater.

INSTALLING HEATER TO WALL

Marking Screw Locations

1.Determine where you will locate heater.

WARNING: Maintain minimum clearances shown in Figure 3. If you can, provide greater clearances from floor and joining wall.

2.Mark two mounting screw locations on wall (see Figure 3).

Installing Two Mounting Screws

Note: Wall anchors and mounting screws are in hardware package. The hardware package is provided with heater.

3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings (see Figure 5).

IMPORTANT: Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

5.Tighten two screws until 1/16" space (thickness of penny) is between screwheads and wall (see Figure 6).

Thin Walls

(1/4" to 1/2" thick)

Figure 4 - Folding Anchor Figure 5 - Popping Open Anchor Wings For Thin Walls

Thin or Thick Wall (thick wall shown)

1/16" Space

JOINING WALL

8 7/8" 7 3/4" Minimum To

Maintain 6"

Clearance

From Wall

Mounting

Screw

Locations

FLOOR

20 1/4"

Minimum To Maintain 3" Clearance From Floor

Solid

Wall

Figure 6 - Tightening Anchors

Placing Heater On Mounting Screws

1.Locate two keyhole slots on back panel of heater (see Figure 7).

2.Place large openings of slots over screwheads. Slide heater down until screws are in small portion of slots.

Figure 3 - Mounting Screw Locations

Attaching To Wall Stud Method

For attaching mounting screw to wall stud

1.Drill hole at marked location using 9/64" drill bit.

2.Insert mounting screw into wall stud.

3.Tighten screw until 1/16" space (thickness of penny) is be- tween screwhead and wall.

Attaching To Wall Anchor Method

Follow instructions below to attach mounting screws to hollow walls (wall areas between studs) or solid walls (concrete or masonry).

1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1 1/4" deep.

2.Fold wall anchor (see Figure 4).

Keyhole Slots

Figure 7 - Location Of Keyhole Slots On Back Panel Of Heater

Removing Front Panel Of

Heater

1.Remove two screws near bot- tom corners of front panel.

2.Lift straight up on grill guard

until it stops. Grill guard will slide up about 1/4".

3. Pull bottom of front panel for- ward, then down.

Figure 8 - Removing Front Panel

Of Heater

For morevisit www..com

110373-01D

REM10PT RH10PT specifications

Desa REM10PT RH10PT is a cutting-edge device that exemplifies innovative engineering in the domain of environmental monitoring and management. Designed to address the increasing demand for smart technology in both urban and rural settings, the REM10PT RH10PT integrates a range of advanced features that allow users to effectively monitor and control their environments.

One of the standout attributes of the REM10PT RH10PT is its exceptional sensor technology. Equipped with high-precision sensors, this device can accurately measure a variety of environmental parameters, including temperature, humidity, air quality, and other critical factors. The real-time data collection ensures that users are kept informed about their surroundings, enabling them to make timely and informed decisions.

The REM10PT RH10PT also boasts a robust connectivity framework. It supports various communication protocols such as Wi-Fi, Bluetooth, and Zigbee, facilitating seamless integration with existing home automation systems. This connectivity allows users to access and manage their devices remotely through a dedicated mobile application, providing convenience and flexibility in monitoring environmental conditions.

Another notable feature of this device is its energy-efficient design. The REM10PT RH10PT is built with sustainability in mind, utilizing low-power components that minimize energy consumption without compromising performance. This not only reduces operational costs but also aligns with the global push for greener technologies.

The user interface is intuitive and user-friendly, offering easy navigation through the device's features and settings. It provides customizable alerts and notifications, allowing users to set parameters according to their specific needs. Whether it’s a simple reminder about humidity levels for plant care or urgent alerts regarding air quality fluctuations, the REM10PT RH10PT delivers pertinent information in real-time.

Lastly, the durability of the REM10PT RH10PT deserves praise. Engineered to withstand varying environmental conditions, the device features weather-resistant housing and high-quality materials that ensure longevity and reliability. This makes it suitable for both indoor applications and outdoor settings, including gardens, farms, and industrial environments.

In summary, the Desa REM10PT RH10PT is an innovative environmental monitoring solution that combines high-precision sensors, robust connectivity, energy efficiency, and user-friendly design. Its versatility and durability make it an essential tool for anyone looking to enhance their awareness and control of environmental conditions. As technology continues to evolve, devices like the REM10PT RH10PT pave the way for a smarter, more connected future.