Bradford-White Corp Commercial Electric Energy Saver Medium Duty E32 Series Models, E32-120R manual

Page 15

 

 

SERVICE PROCEDURE E32-V

 

 

Thermostat Removal and Replacement

Thermostat Removal

WARNING

1.

Turn power “OFF” To water heater.

High voltage exposure. Be sure power is

2.

Remove access cover(s) and insulation.

“OFF” when performing this procedure.

 

3.Remove plastic thermostat protector from thermostat(s).

4.Disconnect wires from thermostat terminals. It may be necessary to label wires for proper re-connection to new thermostat.

5.Note thermostat temperature setting for proper setting of new thermostat.

6.Slide thermostat upwards and out of mounting bracket.

Thermostat Replacement

1.Use a stiff brush to remove any debris or loose scale from tank surface where new thermostat will be installed.

2.Slide new thermostat down into thermostat bracket until it snaps into place. IMPORTANT! Thermostat must set completely flat or flush to tank surface. An improperly installed thermostat will cause improper water heater operation.

3.Refer to the wire diagram located on the inside of the control box cover and re-connect wires to the thermostat. Be sure wire connections are snug and corrosion free. Do not over tighten, doing so may damage thermostat.

4.Set thermostat to the original thermostat setting found on the old thermostat.

5.Re-install plastic thermostat protector.

6.Re-install insulation and access cover.

7.Restore power to water heater and verify proper heater operation.

Tank Surface

Proper Thermostat mounting

flush with tank surface

Thermostat

Improper Thermostat mounting.

Thermostat not flush with tank surface

Thermostat

mounting

bracket

Front View

Thermostat Mounting

Side View

Side View

Proper Thermostat

Improper Thermostat

Mounting

Mounting

Page 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Commercial Electric Energy Saver E32 Medium Duty Commercial Electric Water Heaters Service ProcedureGeneral Information RED Black REDRED Input Kw 208V 240V 277V 380V 415V 480V Full Load Amperes-Phase 1/PhaseSequence of Operation Sequence of OperationField Conversion for E32 Series Phase Conversion Rating Plate Overlay Kits Electrical Phase ConversionThree-Phase to Single-Phase Single-Phase to Three-PhaseBradford White Corporation Rating Plate ModificationTroubleshooting Injury Making voltage checks to avoid personalOFF to water heater prior to performing this Service Procedure E32-IHeating Element Testing High voltage exposure. Be sure power is turnedService Procedure E32-II Line Voltage TestingLine Voltage Testing High voltage exposure. Use caution to avoid Service Procedure E32-IIIFuse Testing Personal injury during this procedureService Procedure E32-IV Thermostat TestingWater Temperature In Tank Is Above Thermostat Setting Thermostat Replacement Service Procedure E32-VHigh voltage exposure. Be sure power is OFF when performing this procedureHeating Element Removal Heating Element ReplacementService Procedure E32-VII Dip Tube and Anode Inspection ReplacementAnode Inspection and Replacement Asse Approved Mixing Valve optional Page Parts@bradfordwhite.com Techserv@bradfordwhite.com
Related manuals
Manual 12 pages 60.05 Kb

Commercial Electric Energy Saver Medium Duty E32 Series Models, E32-80R, E32-50S, E32-120R specifications

Bradford-White Corporation offers a range of high-efficiency water heaters, including the E32 series models: E32-120R, E32-50S, and E32-80R. These models fall under the Commercial Electric Energy Saver Medium Duty category, designed for various commercial applications that require reliable hot water delivery.

The E32 series is built to meet the demands of commercial environments while ensuring energy efficiency. The E32-120R model features a 120-gallon capacity, making it ideal for establishments with high hot water usage. Similarly, the E32-50S offers a 50-gallon capacity, suitable for smaller commercial operations, while the E32-80R provides an 80-gallon option for medium-sized applications. Each model is designed to deliver hot water on demand, with recovery rates optimized for commercial settings.

A notable feature of the E32 series is its Energy Saver technology. These models are equipped with high-efficiency insulation and advanced heating components that minimize heat loss and reduce energy consumption. This not only leads to lower utility bills but also contributes to a reduced carbon footprint, aligning with contemporary environmental standards.

The integration of an advanced electronic control system in the E32 series allows for precise temperature control and monitoring. Users can easily set and adjust water temperatures to meet specific needs, enhancing comfort and safety. Additionally, these models are designed with user-friendly installation features, allowing for straightforward setup and integration into existing systems.

Durability is a hallmark of the E32 series, with each model constructed using high-quality materials that withstand the rigors of commercial use. The tanks are designed to resist corrosion, ensuring a long lifespan and reliable performance. Furthermore, these heaters come with warranties that reflect Bradford-White’s commitment to quality and customer satisfaction.

Maintenance is easy with the E32 series, featuring replaceable heating elements and accessible anodes. This reduces downtime and increases the longevity of the units. Moreover, they comply with all safety and performance regulations, providing peace of mind for business owners.

In summary, the Bradford-White E32-120R, E32-50S, and E32-80R models are versatile, energy-efficient, and durable solutions for commercial hot water needs. Their combination of advanced technology, user-centric features, and robust construction make them a reliable choice for various commercial applications.
Top Page Image Contents