Bradford-White Corp TW450S65F, M4TW60T*F Gas Control & Thermal Well Removal From Water Heater

Page 26

TTW SERVICE PROCEDURE VI

Gas Control & Thermal Well Testing

and Replacement

Gas Control & Thermal Well Removal From Water Heater

 

 

Gas Control

Step 1.

Position gas valve power switch to the “OFF”

Thermal

 

position and Unplug Heater from power supply.

Well

Step 2. Drain heater to a point below the gas control level.

Step 3. Turn off gas supply to water heater and disconnect gas piping from gas control.

Step 4. Disconnect wire harnesses and burner assembly from gas control.

Step 5. Remove gas control & thermal well by rotating flats of Thermal Well counter clockwise (1-5/16"wrench).

Gas Control Removal From Thermal Well

Follow the steps below allows removal gas control from thermal well without removing thermal well from tank.

Step 1. Position gas control power switch to the “OFF” position and unplug water heater from power supply.

Step 2. Turn off gas supply to water heater and disconnect gas piping from gas control.

Step 3. Disconnect wire harnesses & burner assembly from gas control.

Step 4. Using gas control service tool (239-45991-00) available from your BWC parts supplier, Insert tool into back of gas control (see photos below)

View from back of control for clarity

Insert tool from

back of controlService tool shown inserted in to back

of control

Step 5. Pivot tool towards heater as far as possible (see photo below). Lift straight up on gas control. The control should move about 1/8". At this point, remove tool not allowing the control to fall back. With tool removed, lift straight up on control to remove completely from Thermal Well.

With service tool inserted, pivot tool back towards heater as far as possible. Lift straight up on control, control will move 1/8". Remove tool and continue to lift straight up on control to remove from Thermal Well.

Page 26

Page 26

26

Image 26
Contents Service Manual Through-The-Wall Gas Water Heaters For Your Safety Introduction How to Use This Manual Specifications Vent Tables Vent Tables Control Timings Sequence of Operation Steady state operation Pressure Switch/Blower Temperature Fault Troubleshooting Eight-one flash, three Vapor Sensor Burner Inspection and Air Shutter Adjustment Burner Cleaning Pilot Inspection, Testing and Replacement Pressure Switch Testing Pressure Switch Replacement Blower Testing Pressure tapRemove exhaust Blower Temperature Switch Testing Blower Temperature Switch Replacement Gas Control Testing Thermal Well TestingDetermine Water Temperature Inside Tank Gas Control & Thermal Well Removal From Water Heater Gas Control Removal From Thermal WellGas Control Assembly to Thermal Well Flammable Vapor Device Testing Safety Circuit Voltage Trace Red wire leading to blower temperature NVAC Circuit Trace Dip Tube Inspection and Replacement Anode Inspection and Replacement Remove blower to gain access to system from exhaust Flue baffleInner Door Removal Procedure Inner Door Gasket Replacement ProcedureInstallation of Inner Door With Gasket Replace outer jacket burner access door ScreenLok Flame Arrestor Cleaning Glossary of Terms Parts List Parts@bradfordwhite.com Techserv@bradfordwhite.com

M4TW40T*F, M1TW50S*F, M2TW50T*F, M4TW50T*F, M4TW60T*F specifications

Bradford-White Corporation is a leading manufacturer of water heating and storage solutions, known for its commitment to quality and innovation. Among its impressive product lineup, the M2TW65T*F, TW465S65F, TW450S65F, M1TW40S*F, and M1TW60T*F models stand out for their reliability and advanced technology suitable for both residential and commercial applications.

The M2TW65T*F model is distinguished by its high efficiency and performance. It features a 65-gallon capacity, which is ideal for households that require a significant amount of hot water. This model is equipped with an innovative electronic ignition system that enhances energy efficiency while providing reliable hot water on demand. Additionally, it includes advanced insulation technology that minimizes heat loss, ensuring that water remains hot for extended periods.

The TW465S65F and TW450S65F are other exemplary models in the Bradford-White lineup, boasting impressive storage capabilities. Both models offer a combination of a 65-gallon tank and powerful burner systems that significantly reduce recovery time, meaning users can enjoy hot water faster. These models are designed with a user-friendly control panel, making adjustments and monitoring water temperature straightforward. Their robust construction ensures durability and longevity, making them a smart investment.

For smaller households or spaces, the M1TW40S*F and M1TW60T*F models provide excellent options without compromising performance. The M1TW40S*F, with a 40-gallon capacity, is specifically designed for efficiency in limited spaces, while the M1TW60T*F offers extra capacity for larger demands. Both models utilize Bradford-White's state-of-the-art gas burner technology, promoting energy conservation while delivering consistent hot water.

All models are built with a high-quality glass-lined tank to protect against corrosion, further enhancing their lifespan. The incorporation of Bradford-White's exclusive EverKlean technology in their tank designs minimizes sediment buildup, ensuring clean and efficient operation over time.

In addition to their standout performance and efficiency, Bradford-White products prioritize safety. Built-in safety features, such as the temperature and pressure relief valve and advanced venting designs, provide peace of mind for users. These models not only meet but often exceed industry standards for safety and efficiency.

Bradford-White's commitment to innovation and quality is reflected in the M2TW65T*F, TW465S65F, TW450S65F, M1TW40S*F, and M1TW60T*F models, making them excellent choices for anyone in need of reliable hot water solutions. With their advanced technologies, durability, and energy efficiency, these water heaters are ideal for diverse applications in modern homes and businesses.