Bradford-White Corp 238-47808-00A Prepare the Backplate for Wiring, Mount the Protective Plate

Page 10

Remote Mounting the Setback Control

Prepare the Backplate for Wiring

Step 3: Loosen the (3) slotted screws on the backplate attached to the Setback Control Junction Box Assembly. This is shown in Figure 9.

Slotted head

screws

Slotted head screwdriver

Setback Control

Junction Box

Assembly

Backplate (already

installed)

Figure 9

Mount the Protective Plate

Step 4: Mount the Setback Control Protective Plate in a desired location. Be sure that the Setback Control will not be direct sunlight, as the display may be difficult to read. This is shown in Figure 10.

Drill

Wall

Protective

Plate

Figure 10

-10-

Image 10

Contents With Troubleshooting Guide Setback ControlImportant Information Water Heater Setback ControlRead Carefully Important Information Table of Contents Unplug the Water Heater and Setback Control Installing the Setback ControlInspection of Setback Control Install Batteries Removal of Setback Control Protective PlateInstalling Setback Control Powering the Water Heater and Setback ControlRemote Mounting the Setback Control Remove the Setback Control from the BackplatePrepare the Backplate for Wiring Mount the Protective PlateMeasure Wire for Remote Mounting Label the Wires for Remote MountingPrepare the Wires for Installation Install Wire a BackplateFasten Wire a into its Designated Location Backplate Install Wire B BackplateFasten Wire B into its Designated Location Backplate Install Wire C BackplateFasten Wire C into its Designated Location Backplate Route Wires to Protective PlateInstall Wire a Protective Plate Fasten Wire a into its Designated Location Protective PlateInstall Wire B Protective Plate Fasten Wire B into its Designated Location Protective PlateInstall Wire C Protective Plate Fasten Wire C into its Designated Location Protective PlateInstall Setback Control Install Cover PlatePowering the Water Heater and Setback Control Removal of Setback Control Junction Box Assembly Cover Changing the BatteriesReplacement of Batteries Removal of Battery HolderRe-installation of Battery Holder Powering the Water Heater and Setback Control Overview of Control Display and Buttons Right ButtonDisplay Key and Features Display KeyReference Time / Water Temperature Table WakeRevision Level Screen Start-up ProcedureScreen When Power is Applied Select the Correct HourSelect the Correct Minute Locking in the Correct HourLock in the Correct Minute Lock in AM / PM Select AM / PMSelect the Day Finishing the Start-up Procedure Setting the Setback Control Schedule Initial Set-up Setting the ScheduleLock in Wake Period Start Time Lock in Wake Period Water Temperature Select the Wake Period Water TemperatureSelect the Leave Period Start Time Lock in Leave Period Start Time Lock in Leave Period Water Temperature Select the Leave Period Water TemperatureSelect the Return Period Start Time Lock in Return Period Start Time Lock the Return Period Water Temperature Select the Return Period Water TemperatureSelect the Sleep Period Start Time Lock the Sleep Period Start Time Select Sleep Period Water Temperature Lock in Sleep Period Water TemperatureSelect the Day to Edit Enter Editing the Schedule ModeEditing the Setback Schedule Lock in the Day to EditLock in the Wake Period Start Time Edit the Wake Period Start TimeEdit AM / PM Edit the Wake Period Water Temperature Lock in the Wake Period Water TemperatureEdit the Leave Period Start Time Lock in the Leave Period Start TimeEdit the Leave Period Water Temperature Lock in the Leave Period Water TemperatureEdit the Return Period Start Time Lock in the Return Period Start TimeEdit the Return Period Water Temperature Lock in Return Period Water TemperatureEdit the Sleep Period Start Time Lock in the Sleep Period Start TimeEdit the Sleep Period Water Temperature Lock in the Sleep Period Water TemperatureExiting the Edit Schedule Mode Display of Temporary Hold Water Temperature Setting a Temporary Temperature HoldSetting a New Water Temperature Exiting a Temporary HoldDisplay of Permanent Hold Water Temperature Setting a Permanent Temperature HoldExiting a Permanent Hold Select Correct Hour Enter Clock / Day Editing ModeEditing the Clock / Day Lock in Correct HourSelect Correct Minute Lock in Correct MinuteLock in Correct Day & Complete Editing Clock / Day Mode Select Correct DayEnter Sabbath Time Period Editing Sabbath Time Period EditingStart Editing Friday Edit the Wake Period Start Time Lock in AM / PM AM/PM symbol flashes Edit Leave Period Water Temperature Edit the Return Period Start Time Edit Return Period Water Temperature Edit Sleep Period Start Time Lock in Sleep Period Start TimeLock the Sleep Period Water Temperature Continuing with Sabbath Time Period Editing Diagnostic Codes DescriptionPage Page Sales/800-523-2931 Fax/215-641-1670 Parts Fax/215-641-2108 Sales/866-690-0961 Fax/905-238-0105