Bradford-White Corp 47808A Measure Wire for Remote Mounting, Label the Wires for Remote Mounting

Page 11

Remote Mounting the Setback Control

Measure Wire for Remote Mounting

Step 5: Measure and cut (3) pieces of 18 AWG wire to a sufficient length to reach from the backplate on the Setback Control Junction Box Assembly to the Setback Control Protective Plate. This is shown in Figure 11.

18 AWG

Wire

Figure 11

Label the Wires for Remote Mounting

Step 6: Label the (3) cut wires (A), (B), and (C) respectively. Label both ends of the wires. This is shown in Figure 12. Masking tape can be used to label the wires.

Figure 12

Label Each

Wire

-11-

Image 11

Contents Setback Control With Troubleshooting GuideWater Heater Setback Control Important InformationRead Carefully Important Information Table of Contents Inspection of Setback Control Installing the Setback ControlUnplug the Water Heater and Setback Control Removal of Setback Control Protective Plate Install BatteriesPowering the Water Heater and Setback Control Installing Setback ControlRemove the Setback Control from the Backplate Remote Mounting the Setback ControlMount the Protective Plate Prepare the Backplate for WiringLabel the Wires for Remote Mounting Measure Wire for Remote MountingInstall Wire a Backplate Prepare the Wires for InstallationInstall Wire B Backplate Fasten Wire a into its Designated Location BackplateInstall Wire C Backplate Fasten Wire B into its Designated Location BackplateRoute Wires to Protective Plate Fasten Wire C into its Designated Location BackplateFasten Wire a into its Designated Location Protective Plate Install Wire a Protective PlateFasten Wire B into its Designated Location Protective Plate Install Wire B Protective PlateFasten Wire C into its Designated Location Protective Plate Install Wire C Protective PlateInstall Cover Plate Install Setback ControlPowering the Water Heater and Setback Control Changing the Batteries Removal of Setback Control Junction Box Assembly CoverRe-installation of Battery Holder Removal of Battery HolderReplacement of Batteries Powering the Water Heater and Setback Control Right Button Overview of Control Display and ButtonsDisplay Key Display Key and FeaturesWake Reference Time / Water Temperature TableSelect the Correct Hour Start-up ProcedureScreen When Power is Applied Revision Level ScreenLock in the Correct Minute Locking in the Correct HourSelect the Correct Minute Select the Day Select AM / PMLock in AM / PM Finishing the Start-up Procedure Setting the Schedule Setting the Setback Control Schedule Initial Set-upLock in Wake Period Start Time Select the Leave Period Start Time Select the Wake Period Water TemperatureLock in Wake Period Water Temperature Lock in Leave Period Start Time Select the Return Period Start Time Select the Leave Period Water TemperatureLock in Leave Period Water Temperature Lock in Return Period Start Time Select the Sleep Period Start Time Select the Return Period Water TemperatureLock the Return Period Water Temperature Lock the Sleep Period Start Time Lock in Sleep Period Water Temperature Select Sleep Period Water TemperatureLock in the Day to Edit Enter Editing the Schedule ModeEditing the Setback Schedule Select the Day to EditEdit AM / PM Edit the Wake Period Start TimeLock in the Wake Period Start Time Lock in the Wake Period Water Temperature Edit the Wake Period Water TemperatureLock in the Leave Period Start Time Edit the Leave Period Start TimeLock in the Leave Period Water Temperature Edit the Leave Period Water TemperatureLock in the Return Period Start Time Edit the Return Period Start TimeLock in Return Period Water Temperature Edit the Return Period Water TemperatureLock in the Sleep Period Start Time Edit the Sleep Period Start TimeLock in the Sleep Period Water Temperature Edit the Sleep Period Water TemperatureExiting the Edit Schedule Mode Exiting a Temporary Hold Setting a Temporary Temperature HoldSetting a New Water Temperature Display of Temporary Hold Water TemperatureExiting a Permanent Hold Setting a Permanent Temperature HoldDisplay of Permanent Hold Water Temperature Lock in Correct Hour Enter Clock / Day Editing ModeEditing the Clock / Day Select Correct HourLock in Correct Minute Select Correct MinuteSelect Correct Day Lock in Correct Day & Complete Editing Clock / Day ModeStart Editing Friday Sabbath Time Period EditingEnter Sabbath Time Period Editing Edit the Wake Period Start Time Lock in AM / PM AM/PM symbol flashes Edit Leave Period Water Temperature Edit the Return Period Start Time Edit Return Period Water Temperature Lock in Sleep Period Start Time Edit Sleep Period Start TimeLock the Sleep Period Water Temperature Continuing with Sabbath Time Period Editing Description Diagnostic CodesPage Page Sales/866-690-0961 Fax/905-238-0105 Sales/800-523-2931 Fax/215-641-1670 Parts Fax/215-641-2108