Bradford-White Corp 238-47808-00A Prepare the Wires for Installation, Install Wire a Backplate

Page 12

Remote Mounting the Setback Control

Prepare the Wires for Installation

Step 7: Strip approximately ¼” of the wire’s insulation from each end of the three wires. This is shown in Figure 13.

Strip

Approximately ¼” from Each End of All (3) Wires

Figure 13

Install Wire (A) – Backplate

Step 8: Using wire (A), insert one end into the top terminal location on the backplate (located on the Setback Control Junction Box Assembly). This is shown in Figure 14. Be sure that the wire already located in this location is not dislodged.

Wire (A)

Wires Already

Installed

Backplate

Figure 14

-12-

Image 12

Contents With Troubleshooting Guide Setback ControlImportant Information Water Heater Setback ControlRead Carefully Important Information Table of Contents Installing the Setback Control Unplug the Water Heater and Setback ControlInspection of Setback Control Install Batteries Removal of Setback Control Protective PlateInstalling Setback Control Powering the Water Heater and Setback ControlRemote Mounting the Setback Control Remove the Setback Control from the BackplatePrepare the Backplate for Wiring Mount the Protective PlateMeasure Wire for Remote Mounting Label the Wires for Remote MountingPrepare the Wires for Installation Install Wire a BackplateFasten Wire a into its Designated Location Backplate Install Wire B BackplateFasten Wire B into its Designated Location Backplate Install Wire C BackplateFasten Wire C into its Designated Location Backplate Route Wires to Protective PlateInstall Wire a Protective Plate Fasten Wire a into its Designated Location Protective PlateInstall Wire B Protective Plate Fasten Wire B into its Designated Location Protective PlateInstall Wire C Protective Plate Fasten Wire C into its Designated Location Protective PlateInstall Setback Control Install Cover PlatePowering the Water Heater and Setback Control Removal of Setback Control Junction Box Assembly Cover Changing the BatteriesRemoval of Battery Holder Replacement of BatteriesRe-installation of Battery Holder Powering the Water Heater and Setback Control Overview of Control Display and Buttons Right ButtonDisplay Key and Features Display KeyReference Time / Water Temperature Table WakeStart-up Procedure Screen When Power is AppliedRevision Level Screen Select the Correct HourLocking in the Correct Hour Select the Correct MinuteLock in the Correct Minute Select AM / PM Lock in AM / PMSelect the Day Finishing the Start-up Procedure Setting the Setback Control Schedule Initial Set-up Setting the ScheduleLock in Wake Period Start Time Select the Wake Period Water Temperature Lock in Wake Period Water TemperatureSelect the Leave Period Start Time Lock in Leave Period Start Time Select the Leave Period Water Temperature Lock in Leave Period Water TemperatureSelect the Return Period Start Time Lock in Return Period Start Time Select the Return Period Water Temperature Lock the Return Period Water TemperatureSelect the Sleep Period Start Time Lock the Sleep Period Start Time Select Sleep Period Water Temperature Lock in Sleep Period Water TemperatureEnter Editing the Schedule Mode Editing the Setback ScheduleSelect the Day to Edit Lock in the Day to EditEdit the Wake Period Start Time Lock in the Wake Period Start TimeEdit AM / PM Edit the Wake Period Water Temperature Lock in the Wake Period Water TemperatureEdit the Leave Period Start Time Lock in the Leave Period Start TimeEdit the Leave Period Water Temperature Lock in the Leave Period Water TemperatureEdit the Return Period Start Time Lock in the Return Period Start TimeEdit the Return Period Water Temperature Lock in Return Period Water TemperatureEdit the Sleep Period Start Time Lock in the Sleep Period Start TimeEdit the Sleep Period Water Temperature Lock in the Sleep Period Water TemperatureExiting the Edit Schedule Mode Setting a Temporary Temperature Hold Setting a New Water TemperatureDisplay of Temporary Hold Water Temperature Exiting a Temporary HoldSetting a Permanent Temperature Hold Display of Permanent Hold Water TemperatureExiting a Permanent Hold Enter Clock / Day Editing Mode Editing the Clock / DaySelect Correct Hour Lock in Correct HourSelect Correct Minute Lock in Correct MinuteLock in Correct Day & Complete Editing Clock / Day Mode Select Correct DaySabbath Time Period Editing Enter Sabbath Time Period EditingStart Editing Friday Edit the Wake Period Start Time Lock in AM / PM AM/PM symbol flashes Edit Leave Period Water Temperature Edit the Return Period Start Time Edit Return Period Water Temperature Edit Sleep Period Start Time Lock in Sleep Period Start TimeLock the Sleep Period Water Temperature Continuing with Sabbath Time Period Editing Diagnostic Codes DescriptionPage Page Sales/800-523-2931 Fax/215-641-1670 Parts Fax/215-641-2108 Sales/866-690-0961 Fax/905-238-0105