Bradford-White Corp 238-47808-00A, 47808A Fasten Wire B into its Designated Location Backplate

Page 14

Remote Mounting the Setback Control

Fasten Wire (B) into its Designated Location – Backplate

Step 11: Tighten the slotted screw in the middle terminal location on the backplate (located on the Setback Control Junction Box Assembly). This is shown in Figure 17.

Slotted head screwdriver

Wire (A)

Wire (B)

Backplate

Figure 17

Install Wire (C) – Backplate

Step 12: Using wire (C), insert one end into the bottom terminal location on the backplate (located on the Setback Control Junction Box Assembly). This is shown in Figure 18. Be sure that the wire already located in this location is not dislodged.

		Wire (A)
Wire (B)		Wire (A)

Setback Control

Wires Already

Installed

Wire (C)

Figure 18

-14-

Junction Box Assembly

Backplate

Image 14

Contents With Troubleshooting Guide Setback ControlImportant Information Water Heater Setback ControlRead Carefully Important Information Table of Contents Inspection of Setback Control Installing the Setback ControlUnplug the Water Heater and Setback Control Install Batteries Removal of Setback Control Protective PlateInstalling Setback Control Powering the Water Heater and Setback ControlRemote Mounting the Setback Control Remove the Setback Control from the BackplatePrepare the Backplate for Wiring Mount the Protective PlateMeasure Wire for Remote Mounting Label the Wires for Remote MountingPrepare the Wires for Installation Install Wire a BackplateFasten Wire a into its Designated Location Backplate Install Wire B BackplateFasten Wire B into its Designated Location Backplate Install Wire C BackplateFasten Wire C into its Designated Location Backplate Route Wires to Protective PlateInstall Wire a Protective Plate Fasten Wire a into its Designated Location Protective PlateInstall Wire B Protective Plate Fasten Wire B into its Designated Location Protective PlateInstall Wire C Protective Plate Fasten Wire C into its Designated Location Protective PlateInstall Setback Control Install Cover PlatePowering the Water Heater and Setback Control Removal of Setback Control Junction Box Assembly Cover Changing the BatteriesRe-installation of Battery Holder Removal of Battery HolderReplacement of Batteries Powering the Water Heater and Setback Control Overview of Control Display and Buttons Right ButtonDisplay Key and Features Display KeyReference Time / Water Temperature Table WakeRevision Level Screen Start-up ProcedureScreen When Power is Applied Select the Correct HourLock in the Correct Minute Locking in the Correct HourSelect the Correct Minute Select the Day Select AM / PMLock in AM / PM Finishing the Start-up Procedure Setting the Setback Control Schedule Initial Set-up Setting the ScheduleLock in Wake Period Start Time Select the Leave Period Start Time Select the Wake Period Water TemperatureLock in Wake Period Water Temperature Lock in Leave Period Start Time Select the Return Period Start Time Select the Leave Period Water TemperatureLock in Leave Period Water Temperature Lock in Return Period Start Time Select the Sleep Period Start Time Select the Return Period Water TemperatureLock the Return Period Water Temperature Lock the Sleep Period Start Time Select Sleep Period Water Temperature Lock in Sleep Period Water TemperatureSelect the Day to Edit Enter Editing the Schedule ModeEditing the Setback Schedule Lock in the Day to EditEdit AM / PM Edit the Wake Period Start TimeLock in the Wake Period Start Time Edit the Wake Period Water Temperature Lock in the Wake Period Water TemperatureEdit the Leave Period Start Time Lock in the Leave Period Start TimeEdit the Leave Period Water Temperature Lock in the Leave Period Water TemperatureEdit the Return Period Start Time Lock in the Return Period Start TimeEdit the Return Period Water Temperature Lock in Return Period Water TemperatureEdit the Sleep Period Start Time Lock in the Sleep Period Start TimeEdit the Sleep Period Water Temperature Lock in the Sleep Period Water TemperatureExiting the Edit Schedule Mode Display of Temporary Hold Water Temperature Setting a Temporary Temperature HoldSetting a New Water Temperature Exiting a Temporary HoldExiting a Permanent Hold Setting a Permanent Temperature HoldDisplay of Permanent Hold Water Temperature Select Correct Hour Enter Clock / Day Editing ModeEditing the Clock / Day Lock in Correct HourSelect Correct Minute Lock in Correct MinuteLock in Correct Day & Complete Editing Clock / Day Mode Select Correct DayStart Editing Friday Sabbath Time Period EditingEnter Sabbath Time Period Editing Edit the Wake Period Start Time Lock in AM / PM AM/PM symbol flashes Edit Leave Period Water Temperature Edit the Return Period Start Time Edit Return Period Water Temperature Edit Sleep Period Start Time Lock in Sleep Period Start TimeLock the Sleep Period Water Temperature Continuing with Sabbath Time Period Editing Diagnostic Codes DescriptionPage Page Sales/800-523-2931 Fax/215-641-1670 Parts Fax/215-641-2108 Sales/866-690-0961 Fax/905-238-0105