Bradford-White Corp 238-47808-00A, 47808A Removal of Battery Holder, Replacement of Batteries

Page 22

Changing the Batteries

Removal of Battery Holder

Step 3: Remove the battery holder by depressing its top edge and pulling the holder to the right, as shown in Figure 31.

Battery

Holder

Figure 31

Replacement of Batteries

Step 4: Replace the two batteries with (2) AAA batteries. The batteries should be oriented, as shown in Figure 32.

Top of Setback Control (seen from back side)

Figure 32

Re-installation of Battery Holder

Step 5: Replace the battery holder with the new batteries by depressing the top side of the battery holder and pushing on the right side of the holder. This is shown in Figure 33.

Battery

Holder

Figure 33

-22-

Image 22

Contents With Troubleshooting Guide Setback ControlImportant Information Water Heater Setback ControlRead Carefully Important Information Table of Contents Unplug the Water Heater and Setback Control Installing the Setback ControlInspection of Setback Control Install Batteries Removal of Setback Control Protective PlateInstalling Setback Control Powering the Water Heater and Setback ControlRemote Mounting the Setback Control Remove the Setback Control from the BackplatePrepare the Backplate for Wiring Mount the Protective PlateMeasure Wire for Remote Mounting Label the Wires for Remote MountingPrepare the Wires for Installation Install Wire a BackplateFasten Wire a into its Designated Location Backplate Install Wire B BackplateFasten Wire B into its Designated Location Backplate Install Wire C BackplateFasten Wire C into its Designated Location Backplate Route Wires to Protective PlateInstall Wire a Protective Plate Fasten Wire a into its Designated Location Protective PlateInstall Wire B Protective Plate Fasten Wire B into its Designated Location Protective PlateInstall Wire C Protective Plate Fasten Wire C into its Designated Location Protective PlateInstall Setback Control Install Cover PlatePowering the Water Heater and Setback Control Removal of Setback Control Junction Box Assembly Cover Changing the BatteriesReplacement of Batteries Removal of Battery HolderRe-installation of Battery Holder Powering the Water Heater and Setback Control Overview of Control Display and Buttons Right ButtonDisplay Key and Features Display KeyReference Time / Water Temperature Table WakeRevision Level Screen Start-up ProcedureScreen When Power is Applied Select the Correct HourSelect the Correct Minute Locking in the Correct HourLock in the Correct Minute Lock in AM / PM Select AM / PMSelect the Day Finishing the Start-up Procedure Setting the Setback Control Schedule Initial Set-up Setting the ScheduleLock in Wake Period Start Time Lock in Wake Period Water Temperature Select the Wake Period Water TemperatureSelect the Leave Period Start Time Lock in Leave Period Start Time Lock in Leave Period Water Temperature Select the Leave Period Water TemperatureSelect the Return Period Start Time Lock in Return Period Start Time Lock the Return Period Water Temperature Select the Return Period Water TemperatureSelect the Sleep Period Start Time Lock the Sleep Period Start Time Select Sleep Period Water Temperature Lock in Sleep Period Water TemperatureSelect the Day to Edit Enter Editing the Schedule ModeEditing the Setback Schedule Lock in the Day to EditLock in the Wake Period Start Time Edit the Wake Period Start TimeEdit AM / PM Edit the Wake Period Water Temperature Lock in the Wake Period Water TemperatureEdit the Leave Period Start Time Lock in the Leave Period Start TimeEdit the Leave Period Water Temperature Lock in the Leave Period Water TemperatureEdit the Return Period Start Time Lock in the Return Period Start TimeEdit the Return Period Water Temperature Lock in Return Period Water TemperatureEdit the Sleep Period Start Time Lock in the Sleep Period Start TimeEdit the Sleep Period Water Temperature Lock in the Sleep Period Water TemperatureExiting the Edit Schedule Mode Display of Temporary Hold Water Temperature Setting a Temporary Temperature HoldSetting a New Water Temperature Exiting a Temporary HoldDisplay of Permanent Hold Water Temperature Setting a Permanent Temperature HoldExiting a Permanent Hold Select Correct Hour Enter Clock / Day Editing ModeEditing the Clock / Day Lock in Correct HourSelect Correct Minute Lock in Correct MinuteLock in Correct Day & Complete Editing Clock / Day Mode Select Correct DayEnter Sabbath Time Period Editing Sabbath Time Period EditingStart Editing Friday Edit the Wake Period Start Time Lock in AM / PM AM/PM symbol flashes Edit Leave Period Water Temperature Edit the Return Period Start Time Edit Return Period Water Temperature Edit Sleep Period Start Time Lock in Sleep Period Start TimeLock the Sleep Period Water Temperature Continuing with Sabbath Time Period Editing Diagnostic Codes DescriptionPage Page Sales/800-523-2931 Fax/215-641-1670 Parts Fax/215-641-2108 Sales/866-690-0961 Fax/905-238-0105