American Water Heater 316888-004 warranty Water Piping Mixing Valve Usage, Hotter Water can Scald

Page 11

WATER PIPING - MIXING VALVE USAGE

SUGGESTED PIPING

ARRANGEMENT

FOR TOP

CONNECTIONS

SHUT-OFF VALVE

TEMPERED POTABLE WATER

COLD WATER

INLET

THERMAL

EXPANSION

TANK

MIXING

VALVE

(OPTIONAL)

PIPE INSULATION (RECOMMENDED)

METAL

DRAIN PAN

TEMPERED POTABLE WATER

TEMPERATURE- PRESSURE RELIEF VALVE

DISCHARGE

PIPE (DO NOT CAP OR PLUG)

6 in. (15cm)

MAX.

AIR GAP

DRAIN VALVE

FLOOR

TO SUITABLE DRAIN

 

DRAIN

FIGURE 3

This appliance has been design certified as complying with

DO NOT use any pumps, valves, or fittings that are not

ANSI Z21.10.3/CSA 4.3 (latest revision) for water heaters

compatible with potable water.

and is considered suitable for:

DO NOT use valves that may cause excessive restriction

Water (Potable) Heating: All models are considered

to water flow. Use full flow ball or gate valves only.

suitable for water (potable) heating.

DO NOT use any lead based solder in potable water

 

lines. Use appropriate tin-antimony or other equivalent

 

material.

 

DO NOT tamper with the gas control/thermostat, igniter,

 

flammable vapor sensor or temperature and pressure

 

relief valve. Tampering voids all warranties. Only qualified

 

service technicians should service these components.

 

DO NOT use with piping that has been treated with

 

chromates, boiler seal, or other chemicals.

 

DO NOT add any chemicals to the system piping which

 

will contaminate the potable water supply.

Please note the following:

The system should be installed only with piping that is suitable for potable (drinkable) water such as copper, CPVC, PEX or polybutylene. DO NOT use PVC water piping.

HOTTER WATER CAN SCALD:

Water heaters are intended to produce hot water. Water heated to a temperature which will satisfy space heating, clothes washing, dish washing, and other sanitizing needs can scald and permanently injure you upon contact. Some people are more likely to be permanently injured by hot water than others. These include the elderly, children, and the physically or developmentally disabled. If anyone using hot water from this heater fits into one of these

www.americanwaterheater.com

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents AN Odorant is Added to the GAS Used By this Water Heater Power Vent GAS ModelsTable of Contents Important Definitions Safe INSTALLATION, USE and ServiceGeneral Safety Can be triggered at any time Introduction Preparing for the InstallationPage Operation Replacement Parts and Deliming ProductsGET to Know Your Water Heater GAS Models Rough in Dimensions Installation ConsiderationsDirectly BELOW. Keep Clear of ALL Obstructions Hotter Water can Scald Water Piping Mixing Valve UsageSuggested Piping Arrangement For TOP Connections Water Potable Heating All models are consideredFacts to Consider about Location Handle Installation Earthquake Zones Page Appliances in Confined Spaces Combustion AIR and VentilationAppliances in Unconfined Spaces ALL AIR from Outdoors See Figures 12, 13 Thermal Expansion Chemical Vapor CorrosionWater Piping Closed Water SystemsHard Water TEMPERATURE-PRESSURE Relief ValveValve and Pipe Insulation if supplied GAS Piping Filling the Water Heater High Altitude InstallationsGAS Line Purging FLOODING/FREEZINGPlanning the Vent System If using 2 inch vent pipeVent Pipe Termination If using 3 inch vent pipe Masonry Side Walls Installation of Vent SystemVent Terminal INSTALLATION, Sidewall CondensateVent terminals supplied with heater must be used Sequence of InstallationsInstallation Sequence Installation of Vertical Vent System Installation of Vent SYSTEM, SidewallSelection of Materials Vent Pipe PreparationInitial Preparation Step B Recommended BRUSH* Size for Primer Cement ApplicationsStep a Step G Connection to Vent Pipe Power VentStep E Step FVent Hoods MAY be Extremely HOT During Operation Calibration Electrical ConnectionsFilling the Water Heater Display Panel Operating InstructionsPage MCU Lighting Instructions For Your Safety Read Before LightingHeat Cycle Definitions State Description Temperature Regulation Temperature Probes Unique Hybrid FeaturesPage Temperature Regulation Operational Conditions Constant Output Temperature ControlStart UP Conditions Burner Operation and Inspection MaintenanceHousekeeping Venting System InspectionMotors Anode ROD ReplacementTEMPERATURE-PRESSURE Relief Valve Operation Cleaning the Inlet Water FilterFlushing the Heat Exchanger Lime BUILD- UP Cleaning the Heat EngineDraining the Tank Fault Indication and Error CodesCode Display Example Format Diagnostic DisplayRemarks Fault Lockout Code Description Cause Remedy Type Displayed Fault Lockout Code Description Cause Remedy Type Displayed Fault Lockout Code Description Cause Remedy Type Displayed Troubleshooting Stays Cold When the TAP is OpenedThere is no HOT Water or HOT Water Turns ColdLeakage Checkpoints ServiceParts Identification Item # Description AB C DEF KIT # Replacement Parts DescriptionNIP/DIP/TBO/HT Page Page

316888-004 specifications

The American Water Heater 316888-004 is a reliable and efficient choice for homeowners seeking a dependable and effective water heating solution. Designed with a focus on performance and convenience, this water heater provides an impressive array of features that meet the demands of modern living.

One of the standout characteristics of the 316888-004 is its efficient heating technology. The unit employs advanced heating elements that ensure rapid heating of water, reducing wait times for hot water availability. This feature is particularly beneficial for households with high hot water demands, such as those with multiple bathrooms or numerous appliances requiring hot water simultaneously. By delivering hot water quickly, this model enhances user satisfaction and improves overall household efficiency.

In terms of design, the American Water Heater 316888-004 boasts a compact structure, which makes it suitable for various installation environments, including tight spaces. Its durable construction is complemented by high-quality materials, ensuring longevity and reduced maintenance costs. This model is built to withstand the rigors of daily use, providing peace of mind to homeowners regarding its reliability and durability.

Safety is another important aspect of the 316888-004. The unit is equipped with multiple safety features, including a temperature and pressure relief valve, which helps prevent overheating and excessive pressure buildup. Additionally, it accommodates users' needs for energy efficiency, making it an environmentally friendly option. The device is designed to minimize energy consumption, which not only lowers utility bills but also contributes to reducing the household's overall carbon footprint.

Moreover, the 316888-004 is user-friendly, featuring a simple control interface that makes adjusting temperature settings easy. This accessibility allows users to customize their water heating experience according to their personal preferences.

In conclusion, the American Water Heater 316888-004 stands out as a top choice in its category. With its efficient heating technology, durable construction, focus on safety, energy efficiency, and user-friendly features, it meets the diverse needs of contemporary households. For anyone seeking a reliable, high-performance water heater, the 316888-004 is undoubtedly a smart investment, ensuring consistent hot water availability for years to come.
Top Page Image Contents