A.O. Smith 28 30 50 60 service manual Maintenance, Remark Preparation for maintenance

Page 85

s

Introduction

12Maintenance

12.1Introduction

cNote

Maintenance may only by carried out by an approved service and maintenance engineer.

At each service, the appliance undergoes maintenance both on the water side and on the gas side. The maintenance should be carried out in the following order.

1.Preparation for maintenance;

2.Water-side maintenance;

3.Gas-side maintenance;

4.Finalising maintenance.

nRemark

12.2Preparation for maintenance

MENU »OFF ^ ON

È WEEK PROGRAM

Figure 12.1 Main menu

Before ordering spare parts, take a moment to write down the appliance type and model, and the full serial number of the appliance. Only by ordering with this information can you be sure to receive the correct spare parts. These details can be found on the rating plate.

To test whether all components are still working properly, you should complete the following steps:

1.Activate the MENU with B.

2.Use Hand Lto position the cursor beside OFF. See Figure 12.1.

3.Confirm OFF with E.

4.Wait until the fan has stopped. The S icon is then dimmed.

cNote

Failure to wait until the fan stops can cause damage to the appliance.

5.Turn the appliance OFF (position 0) using the ON/OFF switch on the control panel. See Figure 12.2.

6.Turn the ThermoControl ON by putting the ON/OFF switch to position I.

0

I

Figure 12.2 ThermoControl

Release R.1.3 UK

85

Image 85

Contents Release R.1.3 UK Your installer Trademarks CopyrightLiability More informationPage Gis Table of contentsControl panel Filling and drainingStatus of the appliance Starting up and shutting downTroubleshooting Service programMaintenance frequency MaintenanceIndex AppendicesWhat to do if you smell gas Regulations IntroductionAbout the appliance Symbol Target group Target groups Maintenance Forms of notationRemark IntroductionDocument Overview of thisOverview of this document Chapter Target groups DescriptionGis Introduction Functional description of the appliance Functioning of the applianceIntroduction Pressure switch Ionisation rod Water temperature protection Gas controlAppliance’s heating cycle Protection for the appliance Pressure switch Water temperature protectionGas control 3 FanUnvented installation Safety of the instal- lationVented installation Ionisation rodIntroduction Packaging Environmental conditions InstallationMaximum floor loading Humidity and ambient temperatureWater composition Working clearancesWorking clearances Environmental conditionsPlan and elevation of the appliance Technical specificationsTechnical specifications DimensionsDime Description BFC Nsion Unit BFCVAC Gas data Installation diagramGeneral G30-30 mbar butaneUnvented InstallationHot water side Water connections, Unvented Cold water sideCirculation pipe Condensation drainageGas connection Water connections, VentedSee paragraph ’3.6.4 Condensation drainage’ See din FigureAir supply and flue gas discharge Dimension BFCAir supply and flue gas discharge Concentric wall flue terminal Specification DescriptionConcentric roof flue terminal Concentric roof flue terminal specificationsPreparation Electrical connectionPreparation Mains voltage Electrical connection Mains voltageIsolating Transformer Extra on mode switch Tank onContinuous pump Program-controlled pumpChecking the supply Pressure and burner Connecting extra error signal Alarm OUTChecking the supply pressure and burner pressure ApplianceMain menu Conversion to a different gas category Conversion to a different gas categoryRemove the burner as complete assembly Check the burner and supply pressure see paragraph 13 Conversion of gas controlInstallation Filling vented installations Filling the appliance Filling unvented installationsFilling and draining Filling the applianceFilling and draining Installation diagrams F d cDraining vented installations Draining unvented installationsDraining the appliance Draining the applianceGis Introduction Operating Control panelNavigation buttons Explanation of the icons ON/OFF switch of ThermoControlPC connection Control panelStatus of the appliance Operating modes Error conditions Service conditionIntroduction Operating modes Status of the appliance Error conditionsService condition Service conditionGis Starting up and shutting down Open the gas valve see ’ .1 Installation diagrams’Introduction Starting up Shutting downDisconnect the appliance from the mains Shut the appliance down for a brief period OFF modeShut the appliance down for a longer period Starting up and shutting downAppliance’s heating cycle Appliance’s heating cycle12 Ignition Notational convention for menu-related instructions Main menuSetting the water temperature via Setpoint Menu Switching into on mode Setting the water temperatureSetting water temperature during on mode Starting up and shutting down the week program Week programme IntroductionChanging the appliance’s standard week program Remark Setting switch-off time Setting the switch-on timeExample Setting program-controlled pump Setting the water temperatureAdding times to a week program Week programme20 Period added Deleting times from a week program23 week program options Programming an extra period Extra periodSetting menu language SettingsSettings Displaying appliance specifications Remark Setting day and time46 Main menu Gis Setting the hysteresis Service programDisplaying the error history Setting the service interval Setting the pump on/offService program Displaying the appliance historySetting the backlight time Setting the display contrastSetting the display scroll speed Setting the display contrastService program General errors TroubleshootingDisplayed errors Symptom Cause Solution Remark Gas smell Gas leak Troubleshooting table for general errorsSee appendix ’A.2 Electrical diagram BFC’ Symptom Cause Solution Remark Display is offWater leakage Symptom Cause Solution Remark Explosive ignition Troubleshooting table for displayed errorsInsufficient or no hot WaterS03 blocking error S02 blocking errorS04 blocking error S05 blocking errorS14 blocking error S13 blocking errorS15 blocking error F02 lock out error Phase-sensitive. See ’3.10 Electrical connection’Appliance specifications’ How to bleed air from the gas line, and measure the supply F07 lock out error F06 lock out errorF08 lock out error ’3.9 Air supply and flue gas discharge’F10 lock out error Error F09 remains active in the event that the waterRelease R.1.3 UK Release R.1.3 UK E01 blocking error C04 blocking errorE03 blocking error E04 blocking errorDetermining service interval Maintenance frequencyMaintenance frequency Remark Preparation for maintenance MaintenanceStarting up Maintenance Cleaning condensation water discharge Descaling and cleaning the tankCleaning the burner Water-side mainte- nance IntroductionCleaning heat exchanger Cleaning the orifice12.4.3 Remark Finalising mainte- nanceWarranty Certificate Warranty Certificate Week program card AppendicesAppendices Electrical diagramWeek program card Release R.1.3 UK Index IX IndexIX Index 0306