A.O. Smith 28 30 50 60 Installation, Introduction Packaging Environmental conditions

Page 17

is

3

3.1Introduction

3.2Packaging

3.3Environmental conditions

Introduction

Installation

Warning

The installation should be carried out by an approved installer in compliance with the general and local regulations imposed by the gas, water and power supply companies and the fire service.

The appliance may only be installed in a room which complies with the requirements stated in national and local ventilation regulations.

Refer also to paragraph ’1.3 Regulations’.

This chapter describes the installation activities to be carried out before the appliance may be started up, namely:

•Packaging;

•Environmental conditions;

•Technical specifications;

•Water connections, Unvented;

•Water connections, Vented;

•Gas connection;

•Air supply and flue gas discharge;

•Electrical connection;

•Checking the supply pressure and burner pressure;

•Conversion to a different gas category.

nRemark

Starting up the appliance is described in chapter ’7 Starting up and shutting down’.

To avoid damaging the appliance, remove the packaging carefully. We recommend unpacking the appliance at or near its intended location.

cNote

The appliance may only be manoeuvred in an upright position. Take care that the appliance is not damaged after unpacking.

The BFC appliance is a room-sealed appliance. Installation types possible with this appliance are C13, C33, C43, C53 and C63. This makes it possible to install the appliance in either a closed or an open boiler room.

Release R.1.3 UK

17

Image 17

Contents Release R.1.3 UK Your installer Trademarks CopyrightLiability More informationPage Gis Table of contentsControl panel Filling and drainingStatus of the appliance Starting up and shutting downTroubleshooting Service programMaintenance frequency MaintenanceIndex AppendicesAbout the appliance IntroductionWhat to do if you smell gas Regulations Symbol Target group Target groups Maintenance Forms of notationRemark IntroductionDocument Overview of thisOverview of this document Chapter Target groups DescriptionGis Introduction Functioning of the applianceIntroduction Functional description of the appliance Appliance’s heating cycle Protection for the appliance Water temperature protection Gas controlPressure switch Ionisation rod Pressure switch Water temperature protectionGas control 3 FanUnvented installation Safety of the instal- lationVented installation Ionisation rodIntroduction Packaging Environmental conditions InstallationMaximum floor loading Humidity and ambient temperatureWater composition Working clearancesWorking clearances Environmental conditionsPlan and elevation of the appliance Technical specificationsTechnical specifications DimensionsDime Description BFC Nsion Unit BFCVAC Gas data Installation diagramGeneral G30-30 mbar butaneUnvented InstallationHot water side Water connections, Unvented Cold water sideCirculation pipe Condensation drainageGas connection Water connections, VentedSee paragraph ’3.6.4 Condensation drainage’ See din FigureAir supply and flue gas discharge Dimension BFCAir supply and flue gas discharge Concentric wall flue terminal Specification DescriptionConcentric roof flue terminal Concentric roof flue terminal specificationsPreparation Mains voltage Electrical connectionPreparation Electrical connection Mains voltageIsolating Transformer Extra on mode switch Tank onContinuous pump Program-controlled pumpChecking the supply Pressure and burner Connecting extra error signal Alarm OUTChecking the supply pressure and burner pressure ApplianceMain menu Conversion to a different gas category Conversion to a different gas categoryRemove the burner as complete assembly Check the burner and supply pressure see paragraph 13 Conversion of gas controlInstallation Filling vented installations Filling the appliance Filling unvented installationsFilling and draining Filling the applianceFilling and draining Installation diagrams F d cDraining vented installations Draining unvented installationsDraining the appliance Draining the applianceGis Introduction Operating Control panelNavigation buttons Explanation of the icons ON/OFF switch of ThermoControlPC connection Control panelIntroduction Operating modes Operating modes Error conditions Service conditionStatus of the appliance Status of the appliance Error conditionsService condition Service conditionGis Starting up and shutting down Open the gas valve see ’ .1 Installation diagrams’Introduction Starting up Shutting downDisconnect the appliance from the mains Shut the appliance down for a brief period OFF modeShut the appliance down for a longer period Starting up and shutting downAppliance’s heating cycle Appliance’s heating cycle12 Ignition Notational convention for menu-related instructions Main menuSetting water temperature during on mode Switching into on mode Setting the water temperatureSetting the water temperature via Setpoint Menu Changing the appliance’s standard week program Remark Week programme IntroductionStarting up and shutting down the week program Example Setting the switch-on timeSetting switch-off time Setting program-controlled pump Setting the water temperatureAdding times to a week program Week programme20 Period added Deleting times from a week program23 week program options Programming an extra period Extra periodSettings SettingsSetting menu language Displaying appliance specifications Remark Setting day and time46 Main menu Gis Displaying the error history Service programSetting the hysteresis Setting the service interval Setting the pump on/offService program Displaying the appliance historySetting the backlight time Setting the display contrastSetting the display scroll speed Setting the display contrastService program Displayed errors TroubleshootingGeneral errors Symptom Cause Solution Remark Gas smell Gas leak Troubleshooting table for general errorsWater leakage Symptom Cause Solution Remark Display is offSee appendix ’A.2 Electrical diagram BFC’ Symptom Cause Solution Remark Explosive ignition Troubleshooting table for displayed errorsInsufficient or no hot WaterS03 blocking error S02 blocking errorS04 blocking error S05 blocking errorS15 blocking error S13 blocking errorS14 blocking error F02 lock out error Phase-sensitive. See ’3.10 Electrical connection’Appliance specifications’ How to bleed air from the gas line, and measure the supply F07 lock out error F06 lock out errorF08 lock out error ’3.9 Air supply and flue gas discharge’F10 lock out error Error F09 remains active in the event that the waterRelease R.1.3 UK Release R.1.3 UK E01 blocking error C04 blocking errorE03 blocking error E04 blocking errorDetermining service interval Maintenance frequencyMaintenance frequency Remark Preparation for maintenance MaintenanceStarting up Maintenance Cleaning condensation water discharge Descaling and cleaning the tankCleaning the burner Water-side mainte- nance IntroductionCleaning heat exchanger Cleaning the orifice12.4.3 Remark Finalising mainte- nanceWarranty Certificate Warranty Certificate Week program card AppendicesAppendices Electrical diagramWeek program card Release R.1.3 UK Index IX IndexIX Index 0306