Genie 2042, 2022, 2024 manual 3b. Wiring pre-wired, Route wire from wall to Safe-T-Beamsensors -5b

Page 18
Wire Nut
Insulated
Staple

3b. Wiring (pre-wired).

Route wire from wall to Safe-T-Beam®sensors (Fig. 4-5b).

Splice pre-wiring to shortened sensor wire, match wire pairs dash-to-dash(striped-to- striped) and plain-to-plain(white-to-white).

-Trim sensor wire to approximately one foot (1 ft) from sensor.

-Split and strip ends of sensor wires and

pre-wired wires (Fig. 4-7).

- Splice wires together with (provided) wire nuts.

• Route wire from ceiling to power head (Fig. 4-5b).

Securely fasten wires where they exit wall and ceiling as you go.

– Use insulated staples.

– Staples should be snug only.

CAUTION

Staples which are too tight can cut or pinch wires. Cut or pinched wires can cause the Safe-T-Beam®System to stop working. When using the insulated staples, make sure you fasten them only as tightly as needed to hold the wire snugly.

4. Split and strip ends of sensor wires (Fig. 4-7).

NOTE: For rear cover locate Box 4.

5.Attach Safe-T-Beam®wire to power head wire terminal.

Route Safe-T-Beam®wires through wire guide on power head.

Insert wire into terminal holes and lightly press in the orange locking clips above each terminal hole. (You can use a pencil or small screwdriver to comfortably reach in and lightly press down locking clips.) Insert white wires to 'even' numbered terminal holes and striped wires into 'odd' terminal holes (Fig. 4-8).

Wall

 

Wall

 

 

 

 

 

Source

Sensor

 

 

 

 

 

Ceiling

6 5

4 3

2 1

or

6 5

4 3

2 1

Power

Dashed Line = striped wire

Head

Solid Line = white wire

 

FIG. 4-5b Pre-Wired source and sensor wiring methods.

Wire

Insert Wire

Into Connector

 

Wire

 

Use this

 

wire routing

 

if NOT pre-wired

 

Source or Sensor

 

Invisible Light Beam

Source or Sensor

Protection Area

 

FIG. 4-6 Wire routing.

2" 1/2"

FIG. 4-7 Splitting and stripping.

Locking

Clips Terminal

Holes

Confirm wire lock by lightly tugging on the wire. The wire should remain in the terminal hole.

Do not install the white (lamp) cover at this time.

FIG. 4-8 Insert wires.

wire guide

+ –

P B

InfaredSensor

NOTE: Safe-T-Beam®alignment check must be performed following connection to electrical power (see page 19). DO NOT PLUG IN YET!

(Power Head With Rear Cover Removed)

18

PN 37026501206 01/27/2012

 

Image 18
Contents Models 2022/2024/2042 Safety Information Table of Contents Opener FeaturesSafety Features Must be added to these type doors. If this is Check the wall directly above the garageIs your sectional garage door made With a bracing kit. Refer to SectionTypical Sectional Door Installation Recommended Tools Parts Identification Not Shown Full SizeDo not Return to Point of Purchase Chain Piece Rail Hardware Assembled ViewImportant Installation Instructions Pener AssemblyBelt Assembly for Chain Drive Opener Opener Installation Header and Door Mounting Brackets Finding header bracket mounting locationDo not move door spring Mounting the header bracket Mounting the assembly Mounting the OpenerGetting started Install Door Arms Door Bracket2b. Wiring If not pre-wired Wall Console Installation2a. Wiring If pre-wired Wall Console locationSecurely fasten wires Do not install rear cover yet MountingAFE-T-BEAMSYSTEM Installation 3a. Wiring If not pre-wiredMounting Safe-T-BeamSource Red LED and Sensor Green LED 3b. Wiring pre-wired Route wire from wall to Safe-T-Beamsensors -5bWith Power Supplied Onnecting to PowerWith Permanent Wiring With Grounded PlugSetting & Testing OPEN/CLOSE Limits OOR LimitsClose Travel Limit Carriage Lock Keyed Emergency Release Operation InstructionsUP/DOWN Force TestingAdjustment Erase OPEN/CLOSE Travel LimitRogramming Remote Controls Lost or Stolen RemoteLight BULB/LENS Installation Emote ControlDoor balance MaintenanceRoutine Monthly Maintenance Contact reverseCircuit Wiring Diagram Advertencia AvertissementTroubleshooting Guide Operation Problem What to doTroubleshooting Guide Power Head LED Possible Problem SolutionTransmitter Compliance Statement
Related manuals
Manual 68 pages 928 b

2024, 2042, 2022 specifications

Genie is a multi-faceted entertainment platform that has continually evolved since its inception. In 2022, Genie introduced significant updates that enhanced user experience, enabling content personalization through advanced algorithms. Users could access a vast library of shows, movies, and user-generated content tailored to their preferences. The interface saw an overhaul, featuring a sleek design that provided seamless navigation.

Cloud technology played a key role in Genie’s architecture, allowing users to access their content from any device. The transition to Adaptive Streaming Technology (AST) ensured that users experienced high-quality video regardless of their internet speed. Furthermore, Genie integrated social features, where users could share their favorite content, creating a community-driven environment.

By 2024, Genie had further capitalized on Artificial Intelligence (AI) and Machine Learning (ML) to refine its recommendation engine. The platform not only suggested content based on viewing histories but also analyzed social media trends to predict what users might enjoy next. With the introduction of GenieCast, users could share real-time reactions while watching content with friends, no matter their location.

In 2042, Genie transformed into an immersive entertainment ecosystem. The focus on Virtual Reality (VR) and Augmented Reality (AR) technologies allowed users to engage in interactive storytelling experiences. Users could step into the worlds of their favorite shows and movies, becoming part of the narratives. The integration of 360-degree video technology provided a fully immersive viewing experience.

Additionally, Genie’s partnership with various content creators ensured a rich array of exclusive content, appealing to diverse tastes. Enhanced security measures protected user data, ensuring privacy in this interconnected landscape. The collaboration with smart home devices allowed seamless integration, enabling voice-activated controls and personalized content delivery.

Overall, Genie’s evolution from 2022 through 2042 exemplifies the entertainment industry's shift towards user-centric experiences, advanced technologies, and interactive content delivery. With each iteration, Genie has solidified its position as a leader in the entertainment space, continually redefining how audiences engage with media. As technology progresses, users can anticipate even more innovative features that enhance their viewing experiences.