Genie 2024, 2042, 2022 manual OOR Limits, Setting & Testing OPEN/CLOSE Limits, Close Travel Limit

Page 20

6 OOR LIMITS

WARNING

•Severe injury or death can result if the door closing force is set too high.

•Never increase the door closing force above the minimum required to move the door.

•Never adjust force to compensate for a sticking or binding door.

•Perform monthly CONTACT REVERSE TEST as described on page 22 and in Section 10.

SETTING & TESTING OPEN/CLOSE LIMITS

The OPEN (UP) and CLOSE (DOWN) door positions are controlled by making the adjustments on the panel located on the bottom of the power head. The adjustments that can be made are:

•Close Travel Limit,

•Open Travel Limit, Adjust Closing Force Adjust Opening Force Transmitter Programming

A)ENGAGE CHAIN/BELT CONNECTOR TO CARRIAGE

1.Press and hold the "Close Travel Limit" button until the chain or belt connector advances and engages to the Carriage Assembly (Fig. 6-2).

B)CLOSE TRAVEL LIMIT

1.Press and hold the "Close Travel Limit" button until the door is fully closed.

2.You can quickly press and release the "Close Travel Limit" button to move the door in small increments. You can also use the "Open Travel Limit" button to move the door slightly in the UP direction.

3.Door is fully closed when the bottom edge of door presses firmly onto the ground.

4.Once the door is in the desired position, press and hold the "Close SET Limit" SET button for 5 seconds. The LED indicator light will blink green once. This stores the closed position in memory.

C) OPEN TRAVEL LIMIT

1.Press and hold the "Open Travel Limit" button to move the door to its fully opened position. This starts the opener moving in the UP direction.

2.Hold the "Open Travel Limit" button until the door is in the fully opened position that you desire, then release this button.

3.You can quickly press and release the "Open Travel Limit" button to move the door in small increments. You can also use the "Close Travel Limit" button to move the door slightly in the DOWN direction.

4.Once the door is in the desired position, press and hold the "Open SET Limit" SET button for 5 seconds. The LED indicator light will blink green twice. This stores the opened position in memory.

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

Limit Controls location on power head.

NOTE: Set Close Travel Limit before setting Open Travel Limit for unit to operate normally.

Unless limits are being reset do not press set limit buttons.

LED

Open

Open

 

 

Indicator Light

Set Limit

 

Up Force

Travel Limit

 

 

 

Button

OPEN Control

 

 

 

 

 

 

 

 

Adjustment

To

 

 

SET

 

 

Garage Door

 

 

 

 

 

 

LEARN MANUAL LIMIT

FORCE

 

 

 

 

SET

 

 

Learn

 

 

 

 

 

Code

CODE

Close

Close

CLOSE

Down Force

Button

 

 

 

 

 

Travel Limit Set Limit

 

Control

 

 

 

Button

 

Adjustment

FIG. 6-1 Limit controls.

CAUTION

Failure to verify the engagement of the belt/chain connector will result in damage to rail components.

Move

 

 

 

 

in

this

direction

Latch

 

 

 

 

Movement

 

 

 

 

Carriage Assembly

Chain Connector

 

 

 

 

 

 

 

 

Latch

 

 

 

 

Movement

Move

 

 

 

 

in

 

 

 

 

this

direction

Latch

 

 

 

 

 

 

Movement

Carriage Assembly

Belt Connector

Latch

Movement

FIG. 6-2 Engage Chain/Belt Connector to Carriage.

CAUTION

Operation of the opener without the Chain or Belt Connector engaged to the Carriage Assembly will result in damage to rail components including the rail pulley.

20

PN 37026501206 01/27/2012

 

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Models 2022/2024/2042 Safety Information Safety Features Table of ContentsOpener Features Check the wall directly above the garage Is your sectional garage door madeMust be added to these type doors. If this is With a bracing kit. Refer to SectionTypical Sectional Door Installation Recommended Tools Parts Identification Not Shown Full SizeDo not Return to Point of Purchase Chain Piece Rail Hardware Assembled ViewImportant Installation Instructions Pener AssemblyBelt Assembly for Chain Drive Opener Do not move door spring Mounting the header bracket Opener Installation Header and Door Mounting BracketsFinding header bracket mounting location Getting started Mounting the assemblyMounting the Opener Install Door Arms Door BracketWall Console Installation 2a. Wiring If pre-wired2b. Wiring If not pre-wired Wall Console locationSecurely fasten wires Do not install rear cover yet MountingMounting Safe-T-BeamSource Red LED and Sensor Green LED AFE-T-BEAMSYSTEM Installation3a. Wiring If not pre-wired 3b. Wiring pre-wired Route wire from wall to Safe-T-Beamsensors -5bOnnecting to Power With Permanent WiringWith Power Supplied With Grounded PlugClose Travel Limit Setting & Testing OPEN/CLOSE LimitsOOR Limits Carriage Lock Keyed Emergency Release Operation InstructionsTesting AdjustmentUP/DOWN Force Erase OPEN/CLOSE Travel LimitRogramming Remote Controls Lost or Stolen RemoteLight BULB/LENS Installation Emote ControlMaintenance Routine Monthly MaintenanceDoor balance Contact reverseCircuit Wiring Diagram Advertencia AvertissementTroubleshooting Guide Operation Problem What to doTroubleshooting Guide Power Head LED Possible Problem SolutionTransmitter Compliance Statement
Related manuals
Manual 68 pages 928 b

2024, 2042, 2022 specifications

Genie is a multi-faceted entertainment platform that has continually evolved since its inception. In 2022, Genie introduced significant updates that enhanced user experience, enabling content personalization through advanced algorithms. Users could access a vast library of shows, movies, and user-generated content tailored to their preferences. The interface saw an overhaul, featuring a sleek design that provided seamless navigation.

Cloud technology played a key role in Genie’s architecture, allowing users to access their content from any device. The transition to Adaptive Streaming Technology (AST) ensured that users experienced high-quality video regardless of their internet speed. Furthermore, Genie integrated social features, where users could share their favorite content, creating a community-driven environment.

By 2024, Genie had further capitalized on Artificial Intelligence (AI) and Machine Learning (ML) to refine its recommendation engine. The platform not only suggested content based on viewing histories but also analyzed social media trends to predict what users might enjoy next. With the introduction of GenieCast, users could share real-time reactions while watching content with friends, no matter their location.

In 2042, Genie transformed into an immersive entertainment ecosystem. The focus on Virtual Reality (VR) and Augmented Reality (AR) technologies allowed users to engage in interactive storytelling experiences. Users could step into the worlds of their favorite shows and movies, becoming part of the narratives. The integration of 360-degree video technology provided a fully immersive viewing experience.

Additionally, Genie’s partnership with various content creators ensured a rich array of exclusive content, appealing to diverse tastes. Enhanced security measures protected user data, ensuring privacy in this interconnected landscape. The collaboration with smart home devices allowed seamless integration, enabling voice-activated controls and personalized content delivery.

Overall, Genie’s evolution from 2022 through 2042 exemplifies the entertainment industry's shift towards user-centric experiences, advanced technologies, and interactive content delivery. With each iteration, Genie has solidified its position as a leader in the entertainment space, continually redefining how audiences engage with media. As technology progresses, users can anticipate even more innovative features that enhance their viewing experiences.
Top Page Image Contents