Harman-Kardon AVR 310 owner manual If no subwoofer is connected to, Information Display Y

Page 22

System Configuration

If the front left/right speakers are set to LARGE, three options are available:

•If no subwoofer is connected to the

AVR 310, press the ‹/› buttons o 31 on the remote so that NONE appears in the on-screen menu. When this option is selected, all bass information will be routed to the front left/right “main” speakers.

•If a subwoofer is connected to the AVR 310, you have the option to have the front left/right “main” speakers reproduce bass frequencies at all times, and have the sub- woofer operate only when the AVR 310 is being used with a digital source that con- tains a dedicated Low Frequency Effects, or LFE soundtrack. This allows you to use both your main and subwoofer speakers to take advantage of the special bass created for certain movies, press ‹/› buttons o 31 on the remote so that SUB (LFE) appears in the on-screen menu.

•If a subwoofer is connected and you wish to use it for bass reproduction in conjunction with the main front left/right speakers, regardless of the type of program source or surround mode you are listening to, press the ‹/› buttons o 31 on the remote so that SUB LFE+L/R appears in the on-screen menu. When this option is selected, a “complete” feed will be sent to the front left/right “main” speakers, and the subwoofer will receive the bass frequencies under frequency selected in the next option setting on this menu, as described below.

When you have completed your selection for the subwoofer, press the ¤ button n on the remote to change the cursor to SUB X-OVER FREQ. The subwoofer crossover setting may only be adjusted using the on-screen display system.

At this line you will select the frequency at which bass information is directed to the Subwoofer Output ¤. The choices available will depend on the setting made previously for the front left/right speakers. When making these selections, choose the crossover frequency that is closest to that of your front left/right speakers, or the upper frequency limit of your subwoofer. This figure is normally printed in the Owner’s Manual or data sheet for the speakers, or consult the speaker’s manufacturer.

•When the front speakers have been set to LARGE, the crossover choices are 40

Hz or 60 Hz to match the typical crossover points of full range speakers. Choose the option that is closest to your speakers’ design.

•When the front speakers have been set to SMALL, the crossover choices are 80 Hz or 100 Hz to match the typical crossover points of the smaller speakers used in satellite speaker systems. Choose the option that is closest to your speakers’ design.

When all speaker selections have been made, press the ¤ button n and then the Set button p to return to the main menu.

The Speaker Configuration may also be changed at any time without using the full-OSDon-screen menu system by pressing the Speaker Select button on the front panel ı or remote 32 . Once the button is pressed, FNT SPEAKER will appear in both the lower third of the video display and the Main

Information Display Y.

Within three seconds, either press the front panel ‹/› Selector buttons 5 or the ⁄/¤ buttons n on the remote to select a different speaker position, or press the Set button Ôp to begin the adjustment process for the front left and right speakers.

When the Set button Ôp has been pressed and the system is ready for a change to the speaker setting, the on-screen display and Main Information Display Y will read FNT LARGE or FNT SMALL, depend- ing on the current setting. Press the front panel

‹/› Selector Buttons 5 or the ⁄/¤ buttons n on the remote until the desired setting is shown, using the instructions for “large” or “small” shown earlier.

If the configuration for another speaker position needs to be changed, press the front panel ‹/› Selector buttons 5 or the ⁄/¤ buttons n on the remote to select a different speaker position, and then press the front panel ‹/› Selector buttons 5 or the ⁄/¤ buttons n on the remote until the correct speaker setting is shown.

To assist in making speaker configuration set- tings, the icons in the Speaker/Channel Input Indicators Q change as the speaker type is selected at each position. When only the center icon box containing the abbreviation for the speaker position is lit, the speaker is set for

“small.” When the inner box and the two outer boxes with circles inside them are lit, the speaker is set for “large.” When no indicator appears at a speaker location, that position is set for “none” or “no” speaker.

NOTE: These icons are available only when making setup changes in the semi-OSD mode.

As an example, in Figure 6 below, the left front and right front speakers are set for “large,” the center, left surround (LS) and right surround (RS) speakers are set for small, and a sub- woofer is set, as shown by the box with the abbreviation “LFE”, which stands for “low- frequency effects.”

L C R

LS LFE RS

Figure 6

Output Level Adjustment

Output level adjustment is a key part of the configuration process for any surround sound product. It is particularly important for a Dolby Digital receiver such as the AVR 310, as correct outputs will ensure that you hear sound tracks with the proper directionality and intensity.

IMPORTANT NOTE: Listeners are often confused about the operation of the surround channels. While some assume that sound should always be coming from each speaker, most of the time there will be little or no sound in the surround channels. This is because they are only used when a movie director or sound mixer specifically places sound there to create ambience, a special effect or to continue action from the front of the room to the rear. When the output levels are properly set it is normal for surround speakers to operate only occasionally. Artificially increasing the volume to the rear speakers may destroy the illusion of an enveloping sound field that duplicates the way you hear sound in a movie theater or concert hall.

22SYSTEM CONFIGURATION

Page 21 Page 23
Image 22
Page 21 Page 23
Contents AVR 310 Audio/ Video Receiver AVR 310 Audio/ Video Receiver While complex digital systems are hard Description and FeaturesIntroduction Output Levels for OptimumImportant Safety Information Safety InformationUnpacking Front Panel Controls Set Button  Input Indicators Ò Delay# Digital Optical 3 Input Preset Stations Selector Press this SeeNight Mode Indicator This indicator Front Panel Information DisplayOther aspects of the AVR 310’s operation ¢ AM Antenna AC Power Cord Tape Outputs Switched AC Accessory Outlet£ Video 1 Audio Inputs ‡ Unswitched AC Accessory Outlet ¡ Tape InputsRear Panel Connections Main Remote Control Functions AVR SelectorMain Remote Control Functions Dialog center channel intelligibility at low volume levelsTo select the component connected to ` Preset Up/Down When the tuner is37 6-Ch. Direct Input Press this button Channel Direct Input ª as the sourcePower Off When used in the room Zone II Remote Control FunctionsBetween the AM and FM bands Audio Equipment Connections Installation and ConnectionsSystem Installation Connect the analog output of a CD player to the CD inputsSystem and Power Connections Speaker Placement System ConfigurationSpeaker Selection and Placement System Setup32 ı to set the speaker configuration, etc Using the On-Screen DisplaySetting the System Configuration Memories Input Setup Surround SetupNight Mode Settings Buttons on the remote will take you to the delay settingsDelay Settings ¤ button n and then the Set buttonSpeaker Setup SurroundIf no subwoofer is connected to Output Level AdjustmentInformation Display Y Using EzSet Press and hold the SPL Indicator SelectAdditional Input Adjustments Basic Operation OperationSource Selection Surround Mode Chart Selecting a Digital Source Surround Mode SelectionDigital Audio Playback Dolby DigitalNight Mode Digital Status IndicatorsAddition to the bitstream indicators, On the disc to send a full 5.1 feed toMP3 Audio Playback Tuner OperationStation Selection Recalling Preset Stations Output Level Trim AdjustmentPreset Tuning Tape RecordingMemory Backup Channel Direct InputSemi-OSD Settings Advanced FeaturesTurn-On Volume Level Display Brightness AVR 310’s Main Information DisplayFull-OSD Time Out Adjustment Button v to exit the menu systemMultiroom Operation Multiroom SetupInstallation Multiroom OperationProgramming the Remote Programming the RemoteErasing Learned Codes Learning CodesMacro Programming Mode Selector/Channel Down button k Press the Mute 38 button to store the TV Power On CommandErasing Macro Commands Press the AVR Selector fChannel Control Punch-Through Volume Punch-ThroughTransport Control Punch-Through Resetting the Remote Memory Reassigning Device Control SelectorsFunction List Tune Up Preset UpPreset Down DirectSetup Code Table TV 175 176 084001 011 030 033 042 044 100 107 115 154 160 167 168 021 031Setup Code Table VCR 147 166 159057 058 070 074 078 086 114 125 150 167 172Setup Code Table CD 015 075 109 119 158 183 204 037 038 045 046 171 175 202 203020 036 056 057 064 065 089 090 091 092 096 099 104 212 039 051 138 149 209Setup Code Table DVD Setup Code Table TapeSetup Code Table Audio Setup Code NumberSetup Code Table SAT Setup Code Table CBL 055 056 061 099 100 101 207 111 112 213053 214 063 115Information from nonencoded programs Troubleshooting GuideProcessor Reset Lights, motors or other electrical appliancesTechnical Specifications Page Page Harman Kardon, Incorporated Part No. J90200012200

AVR 310 specifications

The Harman-Kardon AVR 310 is a versatile and powerful audio-video receiver that has garnered attention for its blend of performance, design, and features. This model, part of Harman Kardon's distinguished lineage, provides an immersive entertainment experience suitable for both movie enthusiasts and music lovers.

One of the main features of the AVR 310 is its high-quality audio processing capabilities. The receiver supports various surround sound formats, including Dolby Digital and DTS, ensuring that users experience their entertainment in a way that replicates the intended cinematic experience. With its 5.1 channel amplification, the AVR 310 delivers robust sound performance, allowing for a seamless integration of various speaker configurations.

The AVR 310 is equipped with a powerful 50 watts per channel output, offering sufficient power to drive a range of speakers effectively. This amplification enables the receiver to maintain clear audio even at higher volumes, crucial for dynamic scenes in movies or engaging music playback. Additionally, its advanced digital signal processing enhances sound quality, providing users with rich and balanced soundscapes.

In terms of connectivity, the AVR 310 offers a convenient array of inputs and outputs that enhance its versatility. It includes multiple HDMI inputs, component video inputs, and an array of analog inputs, allowing users to connect a variety of devices ranging from gaming consoles to Blu-ray players. The inclusion of a built-in AM/FM tuner ensures users can also enjoy traditional radio programming.

The design of the Harman-Kardon AVR 310 is both sleek and user-friendly. Its modern aesthetics and intuitive front panel make it easy to navigate settings and inputs. The included remote control offers additional convenience, allowing users to control their devices from across the room.

For those looking to create a home theater experience, the AVR 310's capability to use advanced video processing ensures that video signals are upscaled to deliver optimal picture quality. This is particularly beneficial for those with high-definition televisions.

In summary, the Harman-Kardon AVR 310 stands out in the realm of audio-video receivers, providing exceptional audio performance, versatile connectivity, and a user-friendly design. Its combination of features and technologies makes it an ideal choice for anyone looking to enhance their home entertainment system.
Top Page Image Contents