Harman-Kardon AVR 310 owner manual Full-OSD Time Out Adjustment, Button v to exit the menu system

Page 33

Advanced Features

turned off, the semi-OSD displays will remain activated, even if they were switched off for the previous listening session.

To change the length of time that the semi-OSD displays remain on the screen, go to the ADVANCED SELECT Menu as outlined earlier, and press the ⁄/¤ buttons n as needed, until the on-screen › cursor is next to the SEMI-OSD TIME OUT line. Next, press the ‹/› Buttons o 31 until the desired time in seconds is displayed. Note that unlike most of the other options in this menu, this is a permanent setting change, and the time-out entry will remain in effect until it is changed, even when the unit is turned off.

If you wish to make other adjustments, press the ⁄/¤ Buttons n until the on-screen › cursor is next to the desired setting or the RETURN TO MAIN MENU line and press the Set button p. If you have no other adjustments to make, press the OSD Button

vto exit the menu system.

Full-OSD Time Out Adjustment

The FULL-OSD menu system is used to simplify the setup and adjustment of the

AVR 310 using a series of on-screen menus. The factory default setting for these menus leaves them on the screen for 20 seconds after a period of inactivity before they disappear from the screen or Time Out. This Time Out is a safety measure to prevent image retention of the menu text in your monitor or projector, which might happen if they were left on indefinitely. However, some viewers may prefer a slightly longer or shorter period before the Time Out display.

To change the Full-OSD Time Out, you will need to make an adjustment in the ADVANCED SELECT menu (Figure 9). To start the adjustment, press the OSD button v to bring the main AUDIO SETUP menu to the screen. Press the ¤ button n six times, until the on-screen ¤ cursor is next to the ADVANCED line. Press the Set Button p to enter the ADVANCED SELECT Menu (Figure 9).

At the ADVANCED SELECT menu (Figure 9) make certain that the on-screen › cursor is next to the FULL-OSD TIME OUT line by pressing the ⁄/¤ Buttons n as needed. Next, press the ‹/› buttons o/ 31 until the desired time is displayed in seconds.

Note that unlike most of the other options in this menu, this is a permanent setting change, and the Time-Out entry will remain in effect until it is changed, even if the unit is turned off.

If you wish to make other adjustments, press the ⁄/¤ Buttons n until the on-screen › cursor is next to the desired setting or the RETURN TO MAIN MENU line and press the Set button p. If you have no other adjustments to make, press the OSD

button v to exit the menu system.

33ADVANCED FEATURES

Page 32 Page 34
Image 33
Page 32 Page 34
Contents
AVR 310 Audio/ Video Receiver AVR 310 Audio/ Video Receiver Introduction Description and FeaturesWhile complex digital systems are hard Output Levels for OptimumSafety Information Important Safety InformationUnpacking Set Button  Input Indicators Ò Delay Front Panel Controls# Digital Optical 3 Input See Preset Stations Selector Press thisFront Panel Information Display Night Mode Indicator This indicatorOther aspects of the AVR 310’s operation £ Video 1 Audio Inputs ‡ Unswitched AC Accessory Outlet Tape Outputs Switched AC Accessory Outlet¢ AM Antenna AC Power Cord ¡ Tape InputsRear Panel Connections AVR Selector Main Remote Control FunctionsDialog center channel intelligibility at low volume levels Main Remote Control Functions37 6-Ch. Direct Input Press this button ` Preset Up/Down When the tuner isTo select the component connected to Channel Direct Input ª as the sourceZone II Remote Control Functions Power Off When used in the roomBetween the AM and FM bands System Installation Installation and ConnectionsAudio Equipment Connections Connect the analog output of a CD player to the CD inputsSystem and Power Connections Speaker Selection and Placement System ConfigurationSpeaker Placement System SetupUsing the On-Screen Display 32 ı to set the speaker configuration, etcSetting the System Configuration Memories Surround Setup Input SetupDelay Settings Buttons on the remote will take you to the delay settingsNight Mode Settings ¤ button n and then the Set buttonSurround Speaker SetupOutput Level Adjustment If no subwoofer is connected toInformation Display Y Press and hold the SPL Indicator Select Using EzSetAdditional Input Adjustments Operation Basic OperationSource Selection Surround Mode Chart Digital Audio Playback Surround Mode SelectionSelecting a Digital Source Dolby DigitalAddition to the bitstream indicators, Digital Status IndicatorsNight Mode On the disc to send a full 5.1 feed toTuner Operation MP3 Audio PlaybackStation Selection Preset Tuning Output Level Trim AdjustmentRecalling Preset Stations Tape RecordingChannel Direct Input Memory BackupTurn-On Volume Level Advanced FeaturesSemi-OSD Settings Display Brightness AVR 310’s Main Information DisplayButton v to exit the menu system Full-OSD Time Out AdjustmentInstallation Multiroom SetupMultiroom Operation Multiroom OperationProgramming the Remote Programming the RemoteLearning Codes Erasing Learned CodesMacro Programming Erasing Macro Commands Press the Mute 38 button to store the TV Power On CommandMode Selector/Channel Down button k Press the AVR Selector fVolume Punch-Through Channel Control Punch-ThroughTransport Control Punch-Through Reassigning Device Control Selectors Resetting the Remote MemoryFunction List Preset Down Preset UpTune Up DirectSetup Code Table TV 001 011 030 033 042 044 100 107 115 154 160 167 168 084175 176 021 031Setup Code Table VCR 057 058 159147 166 070 074 078 086 114 125 150 167 172Setup Code Table CD 020 036 056 057 064 065 089 090 091 092 096 099 104 212 037 038 045 046 171 175 202 203015 075 109 119 158 183 204 039 051 138 149 209Setup Code Table Audio Setup Code Table TapeSetup Code Table DVD Setup Code NumberSetup Code Table SAT Setup Code Table CBL 053 214 111 112 213055 056 061 099 100 101 207 063 115Processor Reset Troubleshooting GuideInformation from nonencoded programs Lights, motors or other electrical appliancesTechnical Specifications Page Page Harman Kardon, Incorporated Part No. J90200012200