Harman-Kardon AVR 310 Reassigning Device Control Selectors, Resetting the Remote Memory

Page 39

Programming the Remote

Reassigning Device Control Selectors

Although each Input Selector e is normally assigned to the category of product shown on the remote, it is possible to reassign one of these but- tons to operate a second device of another type. For example, if you have two VCRs but no satellite receiver, you may program the “SAT” button to operate a second VCR. Before following the nor- mal programming steps for either Three-Digit entry or Auto Search code entry, you must first reassign the button with the following steps:

1.Press the Input Selector e you wish to reassign and the Mute button 38 at the same time until the red light illuminates under the Input Selector e and the Program/ SPL Indicator c flashes amber.

2.Press the Input Selector e for the device you wish to program into the reassigned button.

3.Enter the three-digit code for the specific model you wish the reassigned button to operate.

4.Press the same Input Selector e pressed in Step 1 once again to store the selection. The red LED under the re-assigned Input Selector will flash three times and then go out.

Example: To use the CBL/SAT button to oper- ate a second VCR, first press the CBL/SAT Input Selector e and the Mute button

38 at the same time until the red light glows under the CBL/SAT e button. Press the VCR e button, followed by the three-digit code for the specific model you wish to control. Finally, press the CBL/SAT e button again.

Resetting the Remote Memory

As you add components to your home-theater sys- tem, occasionally you may wish to totally repro- gram the remote control without the confusion of any commands, macros or ”Punch-Through“ pro- gramming that you may have done. To do this, it is possible to reset the remote to the original factory defaults and command codes by following these steps. Note, however, that once the remote is reset, all commands or codes that you have entered will be erased and will need to be re- entered:

1.Press any of the Input Selector buttons e and the ”O“ button r at the same time until the Program/SPL Indicator c begins to flash amber.

2.Press the ”3“ button r three times.

3.The red LED under the Input Selector e will go out and the Program/SPL Indicator c will stop flashing and turn green.

4.The Program/SPL Indicator c will remain green until the remote is reset. Note that this may take a while, depending on how many commands are in the memory and need to be erased.

5.When the Program/SPL Indicator c goes out, the remote has been reset to the factory settings.

39PROGRAMMING THE REMOTE

Page 38 Page 40
Image 39
Page 38 Page 40
Contents AVR 310 Audio/ Video Receiver AVR 310 Audio/ Video Receiver Output Levels for Optimum Description and FeaturesIntroduction While complex digital systems are hardSafety Information Important Safety InformationUnpacking Set Button  Input Indicators Ò Delay Front Panel Controls# Digital Optical 3 Input See Preset Stations Selector Press thisFront Panel Information Display Night Mode Indicator This indicatorOther aspects of the AVR 310’s operation ¡ Tape Inputs Tape Outputs Switched AC Accessory Outlet£ Video 1 Audio Inputs ‡ Unswitched AC Accessory Outlet ¢ AM Antenna AC Power CordRear Panel Connections AVR Selector Main Remote Control FunctionsDialog center channel intelligibility at low volume levels Main Remote Control FunctionsChannel Direct Input ª as the source ` Preset Up/Down When the tuner is37 6-Ch. Direct Input Press this button To select the component connected toZone II Remote Control Functions Power Off When used in the roomBetween the AM and FM bands Connect the analog output of a CD player to the CD inputs Installation and ConnectionsSystem Installation Audio Equipment ConnectionsSystem and Power Connections System Setup System ConfigurationSpeaker Selection and Placement Speaker PlacementUsing the On-Screen Display 32 ı to set the speaker configuration, etcSetting the System Configuration Memories Surround Setup Input Setup¤ button n and then the Set button Buttons on the remote will take you to the delay settingsDelay Settings Night Mode SettingsSurround Speaker SetupOutput Level Adjustment If no subwoofer is connected toInformation Display Y Press and hold the SPL Indicator Select Using EzSetAdditional Input Adjustments Operation Basic OperationSource Selection Surround Mode Chart Dolby Digital Surround Mode SelectionDigital Audio Playback Selecting a Digital SourceOn the disc to send a full 5.1 feed to Digital Status IndicatorsAddition to the bitstream indicators, Night ModeTuner Operation MP3 Audio PlaybackStation Selection Tape Recording Output Level Trim AdjustmentPreset Tuning Recalling Preset StationsChannel Direct Input Memory BackupDisplay Brightness AVR 310’s Main Information Display Advanced FeaturesTurn-On Volume Level Semi-OSD SettingsButton v to exit the menu system Full-OSD Time Out AdjustmentMultiroom Operation Multiroom SetupInstallation Multiroom OperationProgramming the Remote Programming the RemoteLearning Codes Erasing Learned CodesMacro Programming Press the AVR Selector f Press the Mute 38 button to store the TV Power On CommandErasing Macro Commands Mode Selector/Channel Down button kVolume Punch-Through Channel Control Punch-ThroughTransport Control Punch-Through Reassigning Device Control Selectors Resetting the Remote MemoryFunction List Direct Preset UpPreset Down Tune UpSetup Code Table TV 021 031 084001 011 030 033 042 044 100 107 115 154 160 167 168 175 176Setup Code Table VCR 070 074 078 086 114 125 150 167 172 159057 058 147 166Setup Code Table CD 039 051 138 149 209 037 038 045 046 171 175 202 203020 036 056 057 064 065 089 090 091 092 096 099 104 212 015 075 109 119 158 183 204Setup Code Number Setup Code Table TapeSetup Code Table Audio Setup Code Table DVDSetup Code Table SAT Setup Code Table CBL 063 115 111 112 213053 214 055 056 061 099 100 101 207Lights, motors or other electrical appliances Troubleshooting GuideProcessor Reset Information from nonencoded programsTechnical Specifications Page Page Harman Kardon, Incorporated Part No. J90200012200

AVR 310 specifications

The Harman-Kardon AVR 310 is a versatile and powerful audio-video receiver that has garnered attention for its blend of performance, design, and features. This model, part of Harman Kardon's distinguished lineage, provides an immersive entertainment experience suitable for both movie enthusiasts and music lovers.

One of the main features of the AVR 310 is its high-quality audio processing capabilities. The receiver supports various surround sound formats, including Dolby Digital and DTS, ensuring that users experience their entertainment in a way that replicates the intended cinematic experience. With its 5.1 channel amplification, the AVR 310 delivers robust sound performance, allowing for a seamless integration of various speaker configurations.

The AVR 310 is equipped with a powerful 50 watts per channel output, offering sufficient power to drive a range of speakers effectively. This amplification enables the receiver to maintain clear audio even at higher volumes, crucial for dynamic scenes in movies or engaging music playback. Additionally, its advanced digital signal processing enhances sound quality, providing users with rich and balanced soundscapes.

In terms of connectivity, the AVR 310 offers a convenient array of inputs and outputs that enhance its versatility. It includes multiple HDMI inputs, component video inputs, and an array of analog inputs, allowing users to connect a variety of devices ranging from gaming consoles to Blu-ray players. The inclusion of a built-in AM/FM tuner ensures users can also enjoy traditional radio programming.

The design of the Harman-Kardon AVR 310 is both sleek and user-friendly. Its modern aesthetics and intuitive front panel make it easy to navigate settings and inputs. The included remote control offers additional convenience, allowing users to control their devices from across the room.

For those looking to create a home theater experience, the AVR 310's capability to use advanced video processing ensures that video signals are upscaled to deliver optimal picture quality. This is particularly beneficial for those with high-definition televisions.

In summary, the Harman-Kardon AVR 310 stands out in the realm of audio-video receivers, providing exceptional audio performance, versatile connectivity, and a user-friendly design. Its combination of features and technologies makes it an ideal choice for anyone looking to enhance their home entertainment system.
Top Page Image Contents