Harbor Freight Tools 65322 manual Set Up Instructions, Operating Instructions, Assembly

Page 7

Set Up Instructions

Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

To prevent serious injury

from accidental starting:

Turn the Power Switch of the equipment to its “OFF” position, wait for the engine to cool, and disconnect the spark plug wire(s) before assembling or making any adjustments to the equipment.

To prevent serious injury:

Operate only with proper spark arrestor installed.

Operation of this equipment may create sparks that can start fires around dry vegetation.

A spark arrestor may be required.

The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements.

Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near

the end of this manual.

Assembly

1.Inlet and Outlet Pipes (12) must be attached prior to use. Additional inlet and outlet hoses and clamps (not

included) will be needed depending on the specifics of use.

2.Remove the Pipe Clamps (13) from both Inlet and Outlet Ports of the Pump Housing (10) by turning coun- terclockwise.

3.Place Pipe Clamp (13) over Inlet or Outlet Pipe (12). Position Inlet / Outlet Gasket (11) at Inlet or Outlet Port of the Pump Housing (10). Posi- tion Inlet or Outlet Pipe (12) at Inlet or Outlet Port, and secure in place by turning Pipe Clamp (13) clockwise.

Hand tighten firmly. See Pump As- sembly Diagram on page 20.

Operating Instructions

Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Starting the Engine

Inspect engine and equipment looking for damaged, loose, and missing parts before set up and starting. If any problems are found, do not use equipment until fixed properly.

Checking and Filling Engine Oil

CAUTION! Your Warranty is VOID if the engine’s crankcase is not properly filled with oil before each use. Before each use, check the oil level. Do not run the engine with low or no engine oil. Running the engine with no or low engine oil WILL permanently damage the engine.

SKU 65322 or 65323 For technical questions, please call 1-800-444-3353. Page 7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Distributed exclusively by Harbor Freight Tools For technical questions or replacement parts, please callContents Save This Manual Set up precautionsCarbon Monoxide Hazard Using an engine indoors Operating precautionsIf damaged, have the equipment Service precautionsUnpacking Pump SpecificationsStarting the Engine Set Up InstructionsAssembly Operating InstructionsChecking and Filling Fuel Oil typeBreak-in Period Pump OperationEngine Controls and Indicators Check that all mounting nuts and bolts are tight Pre-Operation ChecksStarting the Engine Stopping the EngineMaintenance Procedures Technical SpecificationsServicing Cleaning Air Filter Element MaintenanceSpark Plug Maintenance Cleaning, Maintenance, Lubrication Schedule Pump Storage Preparation StorageProblem Possible Causes Probable Solutions Engine will not Engine TroubleshootingStart Engine knocks Problem Possible Causes Probable Solutions Engine misfiresEngine stops SuddenlyPart Description ’ty Pump Parts ListPump Troubleshooting Problem Possible Causes Probable SolutionsPump Assembly Diagram Description Qty Crankcase Assembly DiagramQTY Crankcase Cover Assembly DiagramCylinder Head and Cover Assembly Diagram Crankshaft, Piston and Connecting Rod Assembly Diagram Camshaft and Rocker Valve Assembly Diagram Carburetor Assembly Diagram Fuel Tank Assembly Diagram Air Cleaner Assembly Diagram Muffler Assembly Diagram Recoil STarter Assembly Diagram REgulator Control Assembly Diagram Flywheel Assembly Diagram Ignition Coil Assembly Diagram Wiring Diagram Emission Control System Warranty Limited 1 year / 90 Day WarrantyLength of Coverage

65322 specifications

Harbor Freight Tools offers a wide range of products, catering to both professional tradespeople and DIY enthusiasts. One standout item in their extensive lineup is the Harbor Freight Tools 65322, a versatile tool that has garnered significant attention for its impressive features and capabilities.

The Harbor Freight Tools 65322 is primarily recognized as a 12-inch miter saw, designed to deliver precise and clean cuts for various materials. Its powerful motor, providing a robust performance of 15 amps, allows users to tackle tougher cutting tasks with ease. The tool can reach a no-load speed of up to 4,500 RPM, ensuring efficient cutting whether you're working with wood, plastic, or even softer metals. This makes it an invaluable asset for carpenters, woodworkers, and general contractors alike.

One of the standout features of the 65322 is its dual bevel capability, which permits users to make bevel cuts in both directions. This simplifies the cutting process, eliminating the need to flip the workpiece, ultimately saving time and increasing accuracy. The saw features precision mechanical stops for commonly used angles at 0°, 15°, 22.5°, 30°, and 45°, enabling quick adjustments and repeatable cuts. The laser guide system also helps ensure precision in alignment, making it easier to follow cutting lines.

The design of the Harbor Freight Tools 65322 includes a durable and stable base, which enhances overall safety and reduces vibrations during operation. The integrated dust collection bag helps maintain a clean work environment by capturing sawdust and debris, which is crucial for visibility and safety.

In addition to its performance features, the Harbor Freight Tools 65322 is designed with user comfort in mind. Its ergonomic handle provides a secure grip, minimizing hand fatigue during extended use. The saw's lightweight structure further contributes to its ease of use, allowing for portability and simple storage.

Overall, the Harbor Freight Tools 65322 combines powerful performance, precision cutting technology, and user-friendly design. Whether you’re a seasoned professional or a DIY newcomer, this miter saw is a compelling choice for anyone looking to enhance their woodworking experience. With its combination of features and affordability, it represents a solid investment for those serious about their craft.
Top Page Image Contents