Harbor Freight Tools 65322 manual Pump Operation, Break-in Period

Page 9

6.IMPORTANT: Allow the engine to run at no load until warm (1-5 minutes) with no load after each start-up to al- low the engine to stabilize.

Break-in Period

1.Breaking-in the engine will help to ensure proper equipment and engine operation, and will extend the en- gine’s lifespan. The warranty is void if the engine is not broken in properly.

The first 20 hours of operation is the break-in period.

2.During the first 3 hours of use:

•Do not apply a heavy load to the equipment.

•Do not operate the engine at its maximum speed.

3.After the first 20 hours of use:

•Change the engine oil.

Under normal operating conditions subsequent maintenance follows the schedule explained in the Mainte- nance and Servicing section.

Pump Operation

1.Attach flexible input and output hoses

(not included) to the Inlet and Outlet Pipes (12). Secure them with clamps, as the seal must be air and water tight. Attach the included accessory Basket Filter (18 and 19) to the input end of your flexible input hose.

2.CAUTION: Do not operate the pump without a basket filter on the input hose. This prevents large objects from being sucked into the Pump and/or damaging the Pump.

3.Locate the pump as close to the wa- ter as possible. The pump should be on a firm, level surface.

4.Position the input and output hoses as required. Place the input hose in the water to be removed, and output hose in an appropriate location to drain the water. Avoid sharp bends or kinks in the hoses.

5.Check that the pump is not jammed. Disconnect the spark plug wire on the engine, then slowly pull the Starter Handle to rotate the engine and pump. If the pump does not rotate freely, clear it before proceeding.

6.Prime the pump. To do this, remove Access Plug (14) from top of Pump Housing (10). Fill the pump with clean water, then replace the Priming Plug.

CAUTION: Never operate the pump dry, damage may result.

7.Start the engine. The pump will start to operate as soon as the air is re- moved from the input hose.

8.Stop the pump as soon as water is removed. Do not allow pump to run dry, dam- age to the pump will result.

9.Whenever possible, operate the pump for 2-3 minutes with clear water after pumping dirty water to clear it.

10.Drain the water from the pump and disconnect the flexible hoses.

11.To prevent accidents, turn off the engine and disconnect its spark plug wire after use. Wait for the engine to cool, clean external parts with clean cloth, then store the equipment out of children’s reach according to the Storage instructions in this manual.

SKU 65322 or 65323 For technical questions, please call 1-800-444-3353. Page 9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Distributed exclusively by Harbor Freight Tools For technical questions or replacement parts, please callContents Save This Manual Set up precautionsCarbon Monoxide Hazard Using an engine indoors Operating precautionsIf damaged, have the equipment Service precautionsUnpacking Pump SpecificationsAssembly Set Up InstructionsOperating Instructions Starting the EngineChecking and Filling Fuel Oil typeBreak-in Period Pump OperationEngine Controls and Indicators Check that all mounting nuts and bolts are tight Pre-Operation ChecksStarting the Engine Stopping the EngineTechnical Specifications Maintenance ProceduresServicing Air Filter Element Maintenance CleaningSpark Plug Maintenance Cleaning, Maintenance, Lubrication Schedule Pump Storage Preparation StorageEngine Troubleshooting Problem Possible Causes Probable Solutions Engine will notStart Engine stops Problem Possible Causes Probable Solutions Engine misfiresSuddenly Engine knocksPump Troubleshooting Pump Parts ListProblem Possible Causes Probable Solutions Part Description ’tyPump Assembly Diagram Description Qty Crankcase Assembly DiagramQTY Crankcase Cover Assembly DiagramCylinder Head and Cover Assembly Diagram Crankshaft, Piston and Connecting Rod Assembly Diagram Camshaft and Rocker Valve Assembly Diagram Carburetor Assembly Diagram Fuel Tank Assembly Diagram Air Cleaner Assembly Diagram Muffler Assembly Diagram Recoil STarter Assembly Diagram REgulator Control Assembly Diagram Flywheel Assembly Diagram Ignition Coil Assembly Diagram Wiring Diagram Emission Control System Warranty Limited 1 year / 90 Day WarrantyLength of Coverage

65322 specifications

Harbor Freight Tools offers a wide range of products, catering to both professional tradespeople and DIY enthusiasts. One standout item in their extensive lineup is the Harbor Freight Tools 65322, a versatile tool that has garnered significant attention for its impressive features and capabilities.

The Harbor Freight Tools 65322 is primarily recognized as a 12-inch miter saw, designed to deliver precise and clean cuts for various materials. Its powerful motor, providing a robust performance of 15 amps, allows users to tackle tougher cutting tasks with ease. The tool can reach a no-load speed of up to 4,500 RPM, ensuring efficient cutting whether you're working with wood, plastic, or even softer metals. This makes it an invaluable asset for carpenters, woodworkers, and general contractors alike.

One of the standout features of the 65322 is its dual bevel capability, which permits users to make bevel cuts in both directions. This simplifies the cutting process, eliminating the need to flip the workpiece, ultimately saving time and increasing accuracy. The saw features precision mechanical stops for commonly used angles at 0°, 15°, 22.5°, 30°, and 45°, enabling quick adjustments and repeatable cuts. The laser guide system also helps ensure precision in alignment, making it easier to follow cutting lines.

The design of the Harbor Freight Tools 65322 includes a durable and stable base, which enhances overall safety and reduces vibrations during operation. The integrated dust collection bag helps maintain a clean work environment by capturing sawdust and debris, which is crucial for visibility and safety.

In addition to its performance features, the Harbor Freight Tools 65322 is designed with user comfort in mind. Its ergonomic handle provides a secure grip, minimizing hand fatigue during extended use. The saw's lightweight structure further contributes to its ease of use, allowing for portability and simple storage.

Overall, the Harbor Freight Tools 65322 combines powerful performance, precision cutting technology, and user-friendly design. Whether you’re a seasoned professional or a DIY newcomer, this miter saw is a compelling choice for anyone looking to enhance their woodworking experience. With its combination of features and affordability, it represents a solid investment for those serious about their craft.
Top Page Image Contents