Ingersoll-Rand PH15F-XXX-XXX-X manual Ratio Metallic, Service Kits, Pump Data

OPERATOR’S MANUAL PH15F-XXX-XXX-X

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

1.5" DIAPHRAGM PUMP

2:1 RATIO (METALLIC)

RELEASED: 12-14-12 (REV. A)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

SERVICE KITS

Refer to Model Description Chart to match the pump mate- rial options.

637445-XX for Fluid section repair (see page 4). NOTE: This kit also contains several air motor seals which will need to be replaced.

637389 for Air Motor Service Kit (see page 6).

637390-7 for Major Air Valve Kit (see page 7).

PUMP DATA

Models. . . . . . see Model Description Chart for “-XXX” Pump Type. . . . Metallic Air Operated Double Diaphragm Material. . . . . . see Model Description Chart

Weight. . . . . . . . . . . . . . . 88 lbs (39.9 kgs) Maximum Air Inlet Pressure. . . . 100 p.s.i.g. (6.9 bar) Maximum Material Inlet Pressure. . 10 p.s.i.g. (0.69 bar) Maximum Outlet Pressure. . . . . 200 p.s.i.g. (13.8 bar) Maximum Flow Rate. . . . . . . . 63 g.p.m. (238.5 p.m.)

Figure 1

MODEL DESCRIPTION CHART

Displacement / Cycle @ 100 p.s.i.g. 0.88 gal. (3.33 lit.) Maximum Particle Size . . . . . . . 1/4” dia. (6.4 mm)

Maximum Temperature Limits (diaphragm / ball / seal

Pump Size 15 - 1.5”

PH15 F - X S P - S X X - X

material)

E.P.R. / EPDM. . . . . . . . -60° to 280° F (-51° to 138° C) Hytrel®. . . . . . . . . . -20° to 150° F (-29° to 66° C) Polypropylene. . . . . . . 35° to 175° F (2° to 79° C)

Santoprene®. . . . . . . . -40° to 225° F (-40° to 107° C) PTFE. . . . . . . . . . . . . . . . . . . . . . 40° to 225° F (4° to 107° C) Viton®. . . . . . . . . . . -40° to 350° F (-40° to 177° C)

Dimensional Data. . . . . . . . . . see page 8 Noise Level @ 70 p.s.i., 54 c.p.m.. . 75.6 db(A)

Tested with 350-568 muffler assembly installed.

The pump sound pressure levels published here have been updated to

an Equivalent Continuous Sound Level (LAeq) to meet the intent of ANSI S1.13-1971, CAGI-PNEUROP S5.1 using four microphone locations.

NOTICE: All possible options are shown in the chart, however, certain combinations may not be recommended, consult a representative or the factory if you have questions concerning availability.

Air Motor / Air Cap Material

F- Conductive Polypropylene / Stainless Steel

Fluid Connection

A- 1 1/2 N.P.T.F.

B- 1 1/2 BSP parallel

F - 1 1/2 ANSI / DIN Flange

Fluid Cap & Manifold Material

S - Stainless Steel

Hardware Material

P - Plated Steel

Seat Material

S - Stainless Steel

Ball Material

A - Santoprene T - PTFE

C - Hytrel V - Viton

Diaphragm Material

A - Santoprene T - PTFE / Santoprene

C - Hytrel

Fluid Section Service Kit Selection	PH15F - XXX - X X X - X
	637445 -
EXAMPLE: Model #PH15F-ASP-SAA-C		X	X
Fluid Section Service Kit # 637445-XX	Ball			Diaphragm

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET – BRYAN, OHIO 43506

(800) 495-0276  FAX (800) 892-6276	© 2012	CCN 46750519
www.ingersollrandproducts.com