Harman-Kardon AVR4500 owner manual Speaker Selection, Speaker Placement

Page 19

Installation and Connections

Speaker Selection

No matter which type or brand of speakers is used, the same model or brand of speaker should be used for the front-left, center and front-right speakers. This creates a seamless front soundstage and eliminates the possibility of distracting sonic disturbances that occur when a sound moves across mismatched front-channel speakers.

Speaker Placement

The placement of speakers in a multichannel home-theater system can have a noticeable impact on the quality of sound reproduced.

Depending on the type of center-channel speaker in use and your viewing device, place the center speaker either directly above or below your TV, or in the center behind a perforated front-projection screen.

Once the center-channel speaker is installed, position the left-front and right-front speakers so that they are as far away from one another as the center-channel speaker is from the preferred listening position. Ideally, the front-channel speakers should be placed so that their tweeters are no more than 60cm above or below the tweeter in the center-channel speaker.

They should also be at least 0.5 meter from your TV set unless the speakers are magnetically shielded to avoid colourings on the TV screen. Note that most speakers are not shielded, even with complete surround sets only the Center speaker may be.

Depending on the specifics of your room acoustics and the type of speakers in use, you may find that imaging is improved by moving the front-left and front-right speakers slightly forward of the center-channel speaker. If possible, adjust all front loudspeakers so that they are aimed at ear height when you are seated in the listening position.

Using these guidelines, you’ll find that it takes some experimentation to find the correct location for the front speakers in your particular installation. Don’t be afraid to move things around until the system sounds correct. Optimize your speakers so that audio transitions across the front of the room sound smooth.

When the AVR 4500 is used in 5.1-channel oper- ation, the preferred location for surround speak- ers is on the side walls of the room, at or slightly behind the listening position. In a 7.1-channel system, both side surround and back surround speakers are required. The center of the speaker should face you (see below).

Rear surround speakers are required when a full 7.1-channel system is installed, and they may also be used in 5.1 channel mode as an alterna- tive mounting position when it is not practical to place the main surround speakers at the sides of the room. Speakers may be placed on a rear wall, behind the listening position. As with the side speakers, the center of the rear surrounds should face you. The speakers should be no more than 2 meters behind the rear of the seating area.

Subwoofers produce largely nondirectional sound, so they may be placed almost anywhere in a room. Actual placement should be based on room size and shape and the type of subwoofer used. One method of finding the optimal location for a subwoofer is to begin by placing it in the front of the room, about 15cm from a wall, or near the front corner of the room. Another method is to temporarily place the subwoofer in the spot where you will normally sit, and then walk around the room until you find a spot where the subwoofer sounds best. Place the subwoofer in that spot. You should also follow the instructions of the subwoofer’s manufacturer, or you may wish to experiment with the best location for a subwoofer in your listening room.

Center Front Speaker

No more than 60cm

Left Front

 

Right Front

Speaker

 

Speaker

A)Front Channel Speaker Installation with Direct-View TV Sets or Rear-Screen Projectors

 

 

 

TV or Projection Screen

 

 

Left Front

Center Front

Right Front

 

Speaker

 

Speaker

Speaker

 

 

than 2m

-mounted

are used

 

 

No more

when rear

speakers

 

 

 

 

 

Optional Rear-Wall Mounting

 

B)The distance between the left and right

speakers should be equal to the distance from the seating position to the viewing screen. You may also experiment with placing the left and right speakers slightly forward of the center speaker.

Rear speaker mounting is an alternate location for 5.1 systems. It is required for 7.1 operation.

INSTALLATION AND CONNECTIONS 19

Image 19
Contents AVR 4500 Audio/Video Receiver Declaration of Conformity Table of ContentsMain Remote with Internal Codes and Learning Capability Description and FeaturesIntroduction Front panel analog A/V inputsImportant Safety Information Safety InformationUnpacking Front Panel Controls For more information Logic 7 Mode Selector /‹ Button ThisFront Panel Information Display Front Panel Information DisplaySee page 31 for more information on the Sleep function Digital Audio Outputs Connect these Rear Panel ConnectionsRear Panel Connections Rear Panel Connections Main Remote Control Functions Main Remote Control FunctionsEzSet Sensor Microphone Main Remote Control Functions Directly enter a radio station’s frequency ∆ Play Forward/Reverse/Stop ˚ Mute Zone II Remote Control FunctionsVideo Equipment Connections Installation and ConnectionsInstallation and Connections Audio Equipment ConnectionsImportant Note for Adapter Cables Scart A/V ConnectionsVideo Connection Notes Video Video In/Out jacks, if it´s a recording VCRImportant Note for the Use SCART-Cinch Adapters RGB signals can be pathed throughSystem and Power Connections Speaker Selection Speaker PlacementFirst Turn On System ConfigurationUsing the On-Screen Display System ConfigurationSpeaker Setup Input SetupFront panel or Subwoofer SurroundSurround Setup ¤ Button Dso that the cursor is next to Adjustments for Other InputsSettings Keeping Independent from the Input Selected Delay SettingsNight Mode Settings Using EzSet Output Level AdjustmentPress and hold the SPL Indicator Select So that on is highlighted Up the Volume until you can hear the test noise clearly Operation Surround Mode ChartOFF Stereo HallBasic Operation Controls and Use of HeadphonesSource Selection Dolby Digital Surround Mode SelectionDigital Audio Playback 7y, DSP 9Amodes or Stereo $MP3 Audio Playback PCM Audio PlaybackSelecting a Digital Source See Figure Digital Status IndicatorsFront Panel In/Outputs Output Level Adjustment With Source SignalsNight Mode Tape RecordingSelect to activate the sensor Memory BackupTo turn the sensor and indicator off Channel/8-Channel Direct InputDisplay Brightness Advanced FeaturesTurn On Volume Level Advanced FeaturesFull-OSD Time Out Adjustment Semi-OSD SettingsMultiroom Operation InstallationMultiroom Setup Multiroom OperationBasic Tuner Operation Tuner OperationRDS Operation Direct Code Entry Time. When the Program/SPL IndicatorProgramming the Remote Programming the Remote with CodesVID1/VCR VID2/TV Code ReadoutLearning Codes from a Remote Erasing Learned CodesMacro Programming Erasing Macro CommandsPress the AVR Selector 4and the Mute button Volume Punch-ThroughProgrammed Device Functions Remote With Other DevicesSelector button Channel Control Punch-ThroughPress the Input Selector 4you wish to Resetting the Remote Memory Function List Function ListAVR DVD Setup Code Table TV Doric DeccaukDegraaf DixiHyper HigashiHinari HitachiMurphy MitsubishiMivar MultitechRadiola PYEQuasar QuelleStandard SonokoSony Sound WaveSetup Code Table VCR Euroman DynatechElin EsselteKoenig KambrookKansai KenwoodOmaga OceanicittOceanuic OlympusSTS SonamicSontec StrongCode Number 3 digit List Setup Code Table CableCode Number 3digit List Setup Code Table CD Proton NSMOnkyo OptimusSetup Code Table SAT Lenco KosmosKyoto GMI Atlan LemonSkylab SilvaSintrack SKY MasterSetup Code Table DVD Troubleshooting Guide Troubleshooting GuideProcessor Reset Power Switch 1 is pushedTechnical Specifications Harman Consumer International

AVR4500 specifications

The Harman-Kardon AVR4500 is a high-performance AV receiver designed to deliver an immersive audio and visual experience for home theater enthusiasts. With its robust specifications and advanced technology, the AVR4500 stands out as a leading choice for those seeking exceptional sound quality and versatility.

One of the key features of the AVR4500 is its support for multiple audio formats. It is compatible with Dolby Atmos, DTS:X, and other advanced audio technologies, allowing for three-dimensional soundscapes that enhance the cinematic experience. The receiver is equipped with a 9.2-channel configuration, providing ample power and flexibility to drive various speaker setups, including surround sound systems.

The AVR4500 uses Harman's proprietary MultEQ XT32 room calibration technology. This system intelligently analyzes the acoustics of the room and automatically adjusts the sound output to optimize listening conditions. This ensures that users hear their content as intended, regardless of the environment.

In terms of connectivity, the AVR4500 is equipped with a wide range of HDMI inputs and outputs, supporting 4K Ultra HD video and HDR formats such as Dolby Vision and HDR10. This ensures that users can experience the latest high-definition content with stunning clarity and detail. The receiver also features HDMI eARC support, allowing for high-quality audio return channels for compatible TVs.

The AVR4500 supports various streaming services, enabling users to access their favorite music and podcasts effortlessly. With built-in Wi-Fi and Bluetooth, users can stream audio directly from their smartphones or tablets. Additionally, integration with popular voice assistants makes controlling the receiver convenient and user-friendly.

Another notable characteristic of the AVR4500 is its robust power output. It is designed to deliver high-fidelity audio across all channels, ensuring that every sound is clear and richly detailed. With a stylish design featuring a premium finish, this receiver not only performs exceptionally but also adds an elegant touch to any entertainment setup.

Overall, the Harman-Kardon AVR4500 combines cutting-edge technology, outstanding audio performance, and versatile connectivity options, making it an excellent choice for anyone looking to enhance their home theater experience. Whether for movie nights, gaming sessions, or music playback, the AVR4500 offers the quality and performance that audiophiles demand.