Harman-Kardon AVR4500 owner manual Channel Control Punch-Through, Selector button

Page 46

Programming the Remote

Channel Control Punch-Through

The AVR 4500’s remote may be programmed to operate so that the channel control function, performed with the Sleep 9and Surround Abuttons, for either the TV, cable or satellite receiver used in your system may be used in con- junction with one of the other devices controlled by the remote. For example, while using and controlling the VCR, you may wish to change channels on a cable box or satellite receiver without having to change the device selected by the AVR 4500 or the remote. To program the remote for Channel Control Punch-Through, fol- low these steps:

1.Press the Input Selector button 4for the device you wish to have the channel control asso-

ciated with and the Mute button at the same time until the red light illuminates under the Input Selector 4and the Program/SPL Indicator 2flashes amber.

2. Press the Volume Down button . The Program/SPL Indicator 2will stop flashing and stay amber.

3.Press and release the AVR 5or Input Selector button 4for the device that will be used to change the channels. The Program/SPL Indicator 2will blink green three times and then go out to confirm the data entry.

Example: To control the channels using your TV while the remote is set to control the VCR, first press the VID 1/VCR Input Selector button

4and the Mute button at the same time. Next, release them and press the Volume Down button , followed by the same Input

Selector button 4.

NOTE: To remove the Channel Control Punch- Through and return the remote to its original con- figuration, repeat the steps shown in the example above. However, press the same Input Selector in Steps 1 and 3.

Transport Control Punch-Through

The AVR 4500’s remote may be programmed to operate so that the Transport Control Functions P(Play, Stop, Fast Forward, Rewind, Pause and Record) for a VCR, DVD or CD will operate in conjunction with one of the other devices controlled by the remote. For example, while using and controlling the TV, you may wish to start or stop your VCR or DVD without having to change the device selected by the AVR 4500 or the remote. To program the remote for Transport Control Punch-Through, follow these steps:

1.Press the Input Selector 4for the device you wish to have the channel control associated

with and the Mute button at the same time until the red light illuminates, under the Input Selector 4and the Program/ SPL Indicator 2flashes amber.

2.Press the Play button P. The Program/SPL Indicator 2will stop flashing and stay amber.

3.Press and release the AVR 5or Input Selector button 4for the device that will be used to change the channels. The Program/SPL Indicator 2will blink green three times and then go out to confirm the data entry.

Example: To control the transport of a CD player while the remote is set to control the TV, press the VID 2/TV Input Selector button 4and the

Mute button at the same time. Next, release them and press the Play button P, followed by the CD Input Selector button 4.

NOTE: To remove the Channel Control Punch- Through and return the remote to its original con- figuration, repeat the steps shown in the example above. However, press the same Input Selector in Steps 1 and 3.

NOTE: Before programming the remote for Volume, Channel or Transport Punch-Through, make certain that any programming needed for the specific TV, CD, DVD, Cable or Satellite Receivers has been completed.

Reassigning Device-Control Selectors

Although any of the Input Selectors 4is nor- mally assigned to the category of product shown on the remote, it is possible to reassign one of these buttons to operate a second device of another type. For example, if you have two VCRs but no tape, you may program the TAPE 4 button to operate a second VCR. Before you can start you must find out the three-digit code number for your second device (your second VCR) to operate, as outlined on page 42. Then reassign the TAPE 4button with the following steps:

1. Press the Input Selector 4you wish to

reassign and the Mute button at the same time until the red light illuminates under the Input Selector 4and the Program/SPL Indicator 2flashes amber.

2.Press the Input Selector 4for the device, whose function you wish to program into the reassigned button.

3.Enter the three-digit code for the specific model you wish the reassigned button to oper- ate.

4.Press the same Input Selector 4pressed in Step 1 once again to store the selection. The red LED under the re-assigned Input Selector will flash three times and then go out.

Example: To use the TAPE 4button to oper- ate a second VCR, first press the TAPE Input

Selector 4and the Mute button at the same time until the red light glows under the TAPE 4button. Press the VCR 4button, followed by the three-digit code for the specific model you wish to control. Finally, press the TAPE 4button again.

Important Note: Only those Input Selector buttons 4can be reassigned that replace other buttons for devices of the same kind. So the bottons for DVD, CD, TAPE and VCR (devices with transport functions) can replace one anoth- er as the Selectors for TV, CBL/SAT, and VID 4.

To remove the Reassign function and return the remote to its original configuration, repeat steps 1, 3 and 4 above (not 2), however, press the same Input Selector button 4in steps 1 and 4 (i.e. re-program the button with its origi- nal code).

46PROGRAMMING THE REMOTE

Page 45 Page 47
Image 46
Page 45 Page 47
Contents AVR 4500 Audio/Video Receiver Table of Contents Declaration of ConformityFront panel analog A/V inputs Description and FeaturesIntroduction Main Remote with Internal Codes and Learning CapabilityImportant Safety Information Safety InformationUnpacking Front Panel Controls Logic 7 Mode Selector /‹ Button This For more informationFront Panel Information Display Front Panel Information DisplaySee page 31 for more information on the Sleep function Digital Audio Outputs Connect these Rear Panel ConnectionsRear Panel Connections Rear Panel Connections Main Remote Control Functions Main Remote Control FunctionsEzSet Sensor Microphone Main Remote Control Functions Directly enter a radio station’s frequency Zone II Remote Control Functions ∆ Play Forward/Reverse/Stop ˚ MuteAudio Equipment Connections Installation and ConnectionsInstallation and Connections Video Equipment ConnectionsVideo Video In/Out jacks, if it´s a recording VCR Scart A/V ConnectionsVideo Connection Notes Important Note for Adapter CablesRGB signals can be pathed through Important Note for the Use SCART-Cinch AdaptersSystem and Power Connections Speaker Placement Speaker SelectionSystem Configuration System ConfigurationUsing the On-Screen Display First Turn OnSpeaker Setup Input SetupFront panel or Surround SubwooferSurround Setup Delay Settings Adjustments for Other InputsSettings Keeping Independent from the Input Selected ¤ Button Dso that the cursor is next toNight Mode Settings Using EzSet Output Level AdjustmentPress and hold the SPL Indicator Select So that on is highlighted Up the Volume until you can hear the test noise clearly Surround Mode Chart OperationHall OFF StereoBasic Operation Controls and Use of HeadphonesSource Selection 7y, DSP 9Amodes or Stereo $ Surround Mode SelectionDigital Audio Playback Dolby DigitalMP3 Audio Playback PCM Audio PlaybackSelecting a Digital Source Digital Status Indicators See FigureTape Recording Output Level Adjustment With Source SignalsNight Mode Front Panel In/OutputsChannel/8-Channel Direct Input Memory BackupTo turn the sensor and indicator off Select to activate the sensorAdvanced Features Advanced FeaturesTurn On Volume Level Display BrightnessSemi-OSD Settings Full-OSD Time Out AdjustmentMultiroom Operation InstallationMultiroom Setup Multiroom OperationTuner Operation Basic Tuner OperationRDS Operation Programming the Remote with Codes Time. When the Program/SPL IndicatorProgramming the Remote Direct Code Entry Erasing Learned Codes Code Readout Learning Codes from a Remote VID1/VCR VID2/TVMacro Programming Erasing Macro CommandsPress the AVR Selector Remote With Other Devices Volume Punch-ThroughProgrammed Device Functions 4and the Mute buttonSelector button Channel Control Punch-ThroughPress the Input Selector 4you wish to Resetting the Remote Memory Function List Function ListAVR DVD Setup Code Table TV Dixi DeccaukDegraaf DoricHitachi HigashiHinari HyperMultitech MitsubishiMivar MurphyQuelle PYEQuasar RadiolaSound Wave SonokoSony StandardSetup Code Table VCR Esselte DynatechElin EuromanKenwood KambrookKansai KoenigOlympus OceanicittOceanuic OmagaStrong SonamicSontec STSCode Number 3 digit List Setup Code Table CableCode Number 3digit List Setup Code Table CD Optimus NSMOnkyo ProtonSetup Code Table SAT Lemon KosmosKyoto GMI Atlan LencoSKY Master SilvaSintrack SkylabSetup Code Table DVD Power Switch 1 is pushed Troubleshooting GuideProcessor Reset Troubleshooting GuideTechnical Specifications Harman Consumer International
Top Page Image Contents