Harman-Kardon AVR4500 owner manual So that on is highlighted

Page 27

System Configuration

8.After the test noise has circulated once through each channel, it will send the tone to each channel once again, to verify the settings.

9.After two complete circulations of the tone, the levels are set. The Program/SPL Indicator 2will remain green at each channel. Upon completion of the second circu- lation, the Program/SPL Indicator 2will flash green twice and then go out. The tone will stop and the AVR 4500 will return to nor- mal operation.

If you find that the output levels chosen by EzSet are either much lower or much higher than the "0dB" reference setting or even at the limits of the +/-10dB variation range for the output levels, depending on the sensitivity of the speakers in use and your specific room layout, you may repeat the procedure. Return to Step 2 and adjust the master volume either higher or lower appropriately to the output levels set previously (e.g. when levels were set to about "+7dB" reduce the master volume for 7dB), to accommo- date your particular room layout and your speak- ers. You may repeat this procedure as many times as necessary to achieve a desired result. In order to prevent possible damage to your hearing or your equipment, we emphasize that you should avoid setting the master volume above 0dB.

Manual Output Level Adjustment Output levels may also be adjusted manually, either to set them to a specific level with an SPL meter, or to make fine tuning adjustments to the levels obtained using the EzSet remote.

Manual output level adjustment is most easily done through the CHANNEL ADJUST menu (Figure 8). If you are already at the main menu, press the ¤ Button Duntil the on- screen cursor is next to the CHANNEL ADJUST line. If you are not at the main menu, press the OSD Button v to bring up the MASTER MENU (Figure 1), and then press the ¤ Button Dfour times so that the on-screen cursor is next to the CHANNEL ADJUST line. Press the Set Button Fto bring the CHANNEL ADJUST menu (Figure 8) to the screen.

* C H A N N E L A D J U S T

*

F L

: 0 d B

S B R

:

0 d B

C E N : 0 d B

S B L

:

0 d B

F R

: 0 d B

S L

:

0 d B

S R

: 0 d B

S U B

:

0 d B

C H A N N E L R E S E T : O F F O N

T E S T T O N E

: O F F O N

B A C K T O M A S T E R

M E N U

Figure 8

Once the menu appears on your video screen, first use the Button Dto move the on-

screen cursor so that it is next to the TEST TONE line. Press the / Buttons E

so that ON is highlighted.

You will hear a test noise circulate from speaker to speaker in a clockwise direction around the room. The test noise will play for two seconds in each speaker before circulating, and a blinking on-screen cursor will appear next to the name of each speaker location when the sound is at that speaker. Now turn up the volume until you can hear the noise clearly.

IMPORTANT NOTE: Because this test noise will have a much lower level than normal music, the volume must be lowered after the adjustment for all channels is made, but BEFORE you return to the main menu and the test tone turns off.

NOTE: Remember to verify that the speakers have been properly connected. As the test noise circulates, listen to make certain that the sound comes from the speaker position shown in the Main Information Display Y. If the sound comes from a speaker location that does NOT match the position indicated in the display, turn the AVR 4500 off using the Main Power Switch 1 and check the speaker wiring or con- nections to external power amplifiers to make certain that each speaker is connected to the cor- rect output terminal.

After checking for speaker placement, let the test noise circulate again, and listen to see which channels sound louder than the others. Using the front left speaker as a reference, press the /Buttons E on the remote to bring all speakers to the same volume level. When one of the /buttons is pushed, the test noise circula- tion will pause on the channel being adjusted to give you time to make the adjustment. When you release the button, the circulation will resume after five seconds. The on-screen cursor and the test noise can also be moved directly to the speaker to be adjusted by pressing the /¤ buttons Don the remote.

Continue to adjust the individual channels until the volume level sounds the same from each speaker. Note that adjustments should be made with the /Buttons E on the remote only, NOT the main volume controls.

If you are using a sound-pressure level (SPL) meter for precise level adjustment with the test

tone, open the main Volume Control to - 15dB and set the individual output level for each channel so that the meter reads 75dB, C-Weighted Slow. After all settings are made turn the main volume down.

You may also adjust the output levels manually while using the level indication feature of the EzSet remote. To activate the sensor and indica- tor, simply press and release the SPL Indicator

Select Button on the remote while the test tone is circulating and set the main Volume

Control to -15dB (respectively higher or lower, if needed, as outlined above). The Program/SPL Indicator 2will change color to indicate the level. Adjust the level using the /Buttons 5 on the frontpanel until the LED lights green for all channels. When it is red, the level is too high; when it is orange, the level is too low. Press the SPL Indicator Select button when you are finished to turn the sensor and Indicator off.

NOTE: The subwoofer output level is not adjustable using the test tone. To change the subwoofer level, follow the steps for Output Level Trim Adjustment on page 35.

SYSTEM CONFIGURATION 27

Image 27
Contents AVR 4500 Audio/Video Receiver Declaration of Conformity Table of ContentsMain Remote with Internal Codes and Learning Capability Description and FeaturesIntroduction Front panel analog A/V inputsSafety Information Important Safety InformationUnpacking Front Panel Controls For more information Logic 7 Mode Selector /‹ Button ThisFront Panel Information Display Front Panel Information DisplaySee page 31 for more information on the Sleep function Rear Panel Connections Digital Audio Outputs Connect theseRear Panel Connections Rear Panel Connections Main Remote Control Functions Main Remote Control FunctionsEzSet Sensor Microphone Main Remote Control Functions Directly enter a radio station’s frequency ∆ Play Forward/Reverse/Stop ˚ Mute Zone II Remote Control FunctionsVideo Equipment Connections Installation and ConnectionsInstallation and Connections Audio Equipment ConnectionsImportant Note for Adapter Cables Scart A/V ConnectionsVideo Connection Notes Video Video In/Out jacks, if it´s a recording VCRImportant Note for the Use SCART-Cinch Adapters RGB signals can be pathed throughSystem and Power Connections Speaker Selection Speaker PlacementFirst Turn On System ConfigurationUsing the On-Screen Display System ConfigurationInput Setup Speaker SetupFront panel or Subwoofer SurroundSurround Setup ¤ Button Dso that the cursor is next to Adjustments for Other InputsSettings Keeping Independent from the Input Selected Delay SettingsNight Mode Settings Output Level Adjustment Using EzSetPress and hold the SPL Indicator Select So that on is highlighted Up the Volume until you can hear the test noise clearly Operation Surround Mode ChartOFF Stereo HallControls and Use of Headphones Basic OperationSource Selection Dolby Digital Surround Mode SelectionDigital Audio Playback 7y, DSP 9Amodes or Stereo $PCM Audio Playback MP3 Audio PlaybackSelecting a Digital Source See Figure Digital Status IndicatorsFront Panel In/Outputs Output Level Adjustment With Source SignalsNight Mode Tape RecordingSelect to activate the sensor Memory BackupTo turn the sensor and indicator off Channel/8-Channel Direct InputDisplay Brightness Advanced FeaturesTurn On Volume Level Advanced FeaturesFull-OSD Time Out Adjustment Semi-OSD SettingsMultiroom Operation InstallationMultiroom Setup Multiroom OperationBasic Tuner Operation Tuner OperationRDS Operation Direct Code Entry Time. When the Program/SPL IndicatorProgramming the Remote Programming the Remote with CodesVID1/VCR VID2/TV Code ReadoutLearning Codes from a Remote Erasing Learned CodesErasing Macro Commands Macro ProgrammingPress the AVR Selector 4and the Mute button Volume Punch-ThroughProgrammed Device Functions Remote With Other DevicesChannel Control Punch-Through Selector buttonPress the Input Selector 4you wish to Resetting the Remote Memory Function List Function ListAVR DVD Setup Code Table TV Doric DeccaukDegraaf DixiHyper HigashiHinari HitachiMurphy MitsubishiMivar MultitechRadiola PYEQuasar QuelleStandard SonokoSony Sound WaveSetup Code Table VCR Euroman DynatechElin EsselteKoenig KambrookKansai KenwoodOmaga OceanicittOceanuic OlympusSTS SonamicSontec StrongSetup Code Table Cable Code Number 3 digit ListCode Number 3digit List Setup Code Table CD Proton NSMOnkyo OptimusSetup Code Table SAT Lenco KosmosKyoto GMI Atlan LemonSkylab SilvaSintrack SKY MasterSetup Code Table DVD Troubleshooting Guide Troubleshooting GuideProcessor Reset Power Switch 1 is pushedTechnical Specifications Harman Consumer International

AVR4500 specifications

The Harman-Kardon AVR4500 is a high-performance AV receiver designed to deliver an immersive audio and visual experience for home theater enthusiasts. With its robust specifications and advanced technology, the AVR4500 stands out as a leading choice for those seeking exceptional sound quality and versatility.

One of the key features of the AVR4500 is its support for multiple audio formats. It is compatible with Dolby Atmos, DTS:X, and other advanced audio technologies, allowing for three-dimensional soundscapes that enhance the cinematic experience. The receiver is equipped with a 9.2-channel configuration, providing ample power and flexibility to drive various speaker setups, including surround sound systems.

The AVR4500 uses Harman's proprietary MultEQ XT32 room calibration technology. This system intelligently analyzes the acoustics of the room and automatically adjusts the sound output to optimize listening conditions. This ensures that users hear their content as intended, regardless of the environment.

In terms of connectivity, the AVR4500 is equipped with a wide range of HDMI inputs and outputs, supporting 4K Ultra HD video and HDR formats such as Dolby Vision and HDR10. This ensures that users can experience the latest high-definition content with stunning clarity and detail. The receiver also features HDMI eARC support, allowing for high-quality audio return channels for compatible TVs.

The AVR4500 supports various streaming services, enabling users to access their favorite music and podcasts effortlessly. With built-in Wi-Fi and Bluetooth, users can stream audio directly from their smartphones or tablets. Additionally, integration with popular voice assistants makes controlling the receiver convenient and user-friendly.

Another notable characteristic of the AVR4500 is its robust power output. It is designed to deliver high-fidelity audio across all channels, ensuring that every sound is clear and richly detailed. With a stylish design featuring a premium finish, this receiver not only performs exceptionally but also adds an elegant touch to any entertainment setup.

Overall, the Harman-Kardon AVR4500 combines cutting-edge technology, outstanding audio performance, and versatile connectivity options, making it an excellent choice for anyone looking to enhance their home theater experience. Whether for movie nights, gaming sessions, or music playback, the AVR4500 offers the quality and performance that audiophiles demand.