Clarke L26 manual Battery Maintenance

Page 13

How To Prepare the Machine For Operation

Battery Maintenance

The electrical power to operate the machine comes from the storage batteries. Storage batteries need preventativemaintenance.

WARNING: Working with batteries can be dangerous. Always wear eye protection and protective clothing when working near batteries. NO SMOKING!

To maintain the batteries in good condition, follow these instructions:

1.Keep the electrolyte at the correct level. The correct level is between 1/4" (1/2 cm) below the bottom of the tube in each cell and above the tops of the plates. Check the level of the electro- lyte each time you charge the batteries. See figure 10.

NOTE: Check the level of electrolyte prior to charging the batteries. Be sure the plates in each cell are covered with electrolyte before charging. Do not top off the cells prior to charging the battery. Electrolyte expands during charging. As a result, the electrolyte could overflow from the cells. Always top off the cells with distilled water after charging.

CAUTION: Irreversible damage will occur to the batteries if electrolyte does not cover the plates. Keep the electrolyte at the correct level.

CAUTION: Machine damage and discharge across the tops of the batteries can occur if the batteries are over filled. Do not fill the batteries up to the bottom of the tube in each cell. Wipe any acid from the machine or the tops of the batter- ies. Never add acid to a battery after installation.

CAUTION: Batteries must be refilled with distilled water only. Do not use tap water as it may contain contaminants that will damage batteries.

2.Keep the tops of the batteries clean and dry. Keep the terminals and connectors clean. To clean the top of the batteries, use a damp cloth with a weak solution of ammonia or bicarbonate of soda solution. To clean the terminals and connectors, use a terminal and connector cleaning tool. Do not allow ammonia or bicar- bonate of soda to get into batteries.

Correct Level

Figure 10

Figure 11

3.Keep the batteries charged.

4.To drain battery compartment: (See figure 11)

a.Always wear protective eye protection and protective clothing.

b.Add a weak solution of ammonia or bicarbon- ate of soda solution to battery compartment to neutralize any spilled acid.

c. Pull drain hose out from under transaxle.

d.Place hand behind flange and open valve.

e.When empty, close valve.

f.Replace valve and drain hose on top of transaxle.

g.Neutralize any acid spills with ammonia or bicarbonate of soda.

CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical

Page -13-

Image 13
Contents Read this Book ManualTable of Contents Severe bodily injury or death. Read and observe all Danger Avertissement AdvertenciaClarke Technology Operators Manual -Encore L26 Cylindrical Introduction & Machine Specifications Introduction & Machine SpecificationsFigure #1 Procedures For TransportingProcedures For Transpoting Symbols Used on Encore L26 Cylindrical Symbols Used on Encore L26 Cylindrical Machine Control Panel Key Switch See , Item aHour Meter Not Illustrated Option Parking Brake Optional, See Figure Machine Controls and FeaturesHow To Install The Batteries How To Prepare the Machine For OperationBattery Maintenance How To Charge The Batteries How To Change or Rotate Brushes How To Operate The Squeegee How To Operate The MachineHow To Fill The Solution Tank Operating The Machine How To Clean a FloorHow To Clean a Very Dirty Floor These Maintenance Procedures Must Be Done Every Day MaintenanceDo These Procedures When You Begin Your Work Period Do These Procedures When You End Your Work MaintenanceDistilled Water only Maintenance Procedures To Be Done Every WeekMaintenance For The Squeegee Adjusting Squeegee Tilt How To Adjust The SqueegeeAdjusting Squeegee Blades How to Center or Offset the Brush HeadHow to Level the Cylindrical Brush Head Squeegee Blades Description Assembly Clarke Technology Encore L26 Cylindrical Accessories 3/02Description Brushes Size Description Used ForClarke Technology Operators Manual -Encore L26 Cylindrical Encore There is no solution flow HOW to Correct Problems in the Machine Cause ActionProblem Cause Action Page Alto Product Support Branches Battery Warranty Clarke Technology Limited U.S. WarrantyAlways use genuine ClarkeTechnology Parts for repair Highway Springdale, Arkansas

L26 specifications

The Clarke L26 stands as a notable entry in the realm of compact excavators, reflecting advanced engineering and user-centric design. This machine is designed for a variety of applications, including landscaping, utility work, and smaller construction projects.

One of the main features of the Clarke L26 is its compact size, which allows it to maneuver easily through tight spaces and urban environments. This machine has an overall width of approximately 2.6 meters, making it suitable for projects that require a mini excavator that can fit through narrow gaps and access constrained job sites.

Powered by a robust and efficient diesel engine, the L26 delivers optimal performance without compromising on fuel efficiency. The engine is designed to meet stringent emissions standards while providing ample torque for digging and lifting tasks. The hydraulic system of the L26 is another standout characteristic, featuring sophisticated components that ensure smooth operation and responsiveness during various digging and lifting operations.

The L26 also incorporates advanced technology that enhances operator comfort and productivity. Its spacious cab features ergonomic controls, providing operators with a user-friendly interface. The visibility from the cab is optimized to reduce blind spots, enabling the operator to work safely and efficiently. Additionally, the climate control system in the cab ensures a comfortable working environment, regardless of external weather conditions.

Safety features are paramount in the design of the Clarke L26. It comes equipped with a rollover protective structure (ROPS) and a falling-object protective structure (FOPS), which provide peace of mind to operators working in hazardous conditions. The machine's low center of gravity enhances stability, especially when working on uneven terrain.

In terms of versatility, the Clarke L26 can be outfitted with various attachments such as buckets, augers, and hydraulic breakers, allowing it to tackle a multitude of tasks beyond traditional excavation. The quick coupler system enables easy switching between attachments, significantly reducing downtime during operations.

Overall, the Clarke L26 can be described as a well-rounded mini excavator that combines power, efficiency, and versatility. Its design is aimed at meeting the demands of modern construction and landscaping projects, making it a valuable asset for contractors and operators alike. Whether it's for digging trenches, landscaping gardens, or performing utility work, the L26 proves to be a competent machine that delivers reliable performance.