Clarke L26 manual How To Change or Rotate Brushes

Page 15

How To Prepare the Machine For Operation

4.Disconnect the battery pack connector from the control housing connector. See figure 14A.

5.Connect the DC connector on the charger to the battery pack connector. See figure 14B.

6.Connect the charger to a properly grounded single phase (3-wire) wall receptacle having the input voltage, fre- quency, and ampere capacity specified on the nameplate of the charger.

For more information on the use of the charger, read the instructions supplied with the charger.

How To Change or Rotate Brushes

To install or rotate brushes on the machine, follow this procedure:

1.Turn the key switch "ON".

2.Raise the brush head by pressing and holding the brush switch until brush head is in full up position,

3.Turn the key switch "OFF" and remove the key.

4.Go to the front of the machine and remove thumb screw from brush door (figure 15).

5.Lower door approximately ½ inch and slide door and bearing assembly off shaft (figure 16).

6.Remove brush spacer and brush by sliding off of brush shaft (figure 17).

7.Rotate brush or replace.

8.Slide brush on shaft and rotate slowly until drive pins are lined up with brush slots. Push brush all the way in.

9.Install brush spacer on shaft.

10.Slide brush door bearing assembly on shaft.

11.Raise door and install thumb screw.

DANGER: Operating a machine that is not completely or fully assembled could result in injury or property damage. Do not operate this machine unless it is completely assembled. Inspect the machine carefully before operation.

Figure 17

Figure 14A

Figure 14B

Figure 15

Figure 16

CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical

Page -15-

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Read this Book ManualTable of Contents Severe bodily injury or death. Read and observe all Danger Avertissement AdvertenciaClarke Technology Operators Manual -Encore L26 Cylindrical Introduction & Machine Specifications Introduction & Machine SpecificationsFigure #1 Procedures For TransportingProcedures For Transpoting Symbols Used on Encore L26 Cylindrical Symbols Used on Encore L26 Cylindrical Key Switch See , Item a Machine Control PanelHour Meter Not Illustrated Option Parking Brake Optional, See Figure Machine Controls and FeaturesHow To Install The Batteries How To Prepare the Machine For OperationBattery Maintenance How To Charge The Batteries How To Change or Rotate Brushes How To Operate The Machine How To Operate The SqueegeeHow To Fill The Solution Tank Operating The Machine How To Clean a FloorHow To Clean a Very Dirty Floor Maintenance These Maintenance Procedures Must Be Done Every DayDo These Procedures When You Begin Your Work Period Do These Procedures When You End Your Work MaintenanceDistilled Water only Maintenance Procedures To Be Done Every WeekMaintenance For The Squeegee How to Center or Offset the Brush Head How To Adjust The SqueegeeAdjusting Squeegee Tilt Adjusting Squeegee BladesHow to Level the Cylindrical Brush Head Brushes Size Description Used For Clarke Technology Encore L26 Cylindrical Accessories 3/02Squeegee Blades Description Assembly DescriptionClarke Technology Operators Manual -Encore L26 Cylindrical Encore There is no solution flow HOW to Correct Problems in the Machine Cause ActionProblem Cause Action Page Alto Product Support Branches Highway Springdale, Arkansas Clarke Technology Limited U.S. WarrantyBattery Warranty Always use genuine ClarkeTechnology Parts for repair

L26 specifications

The Clarke L26 stands as a notable entry in the realm of compact excavators, reflecting advanced engineering and user-centric design. This machine is designed for a variety of applications, including landscaping, utility work, and smaller construction projects.

One of the main features of the Clarke L26 is its compact size, which allows it to maneuver easily through tight spaces and urban environments. This machine has an overall width of approximately 2.6 meters, making it suitable for projects that require a mini excavator that can fit through narrow gaps and access constrained job sites.

Powered by a robust and efficient diesel engine, the L26 delivers optimal performance without compromising on fuel efficiency. The engine is designed to meet stringent emissions standards while providing ample torque for digging and lifting tasks. The hydraulic system of the L26 is another standout characteristic, featuring sophisticated components that ensure smooth operation and responsiveness during various digging and lifting operations.

The L26 also incorporates advanced technology that enhances operator comfort and productivity. Its spacious cab features ergonomic controls, providing operators with a user-friendly interface. The visibility from the cab is optimized to reduce blind spots, enabling the operator to work safely and efficiently. Additionally, the climate control system in the cab ensures a comfortable working environment, regardless of external weather conditions.

Safety features are paramount in the design of the Clarke L26. It comes equipped with a rollover protective structure (ROPS) and a falling-object protective structure (FOPS), which provide peace of mind to operators working in hazardous conditions. The machine's low center of gravity enhances stability, especially when working on uneven terrain.

In terms of versatility, the Clarke L26 can be outfitted with various attachments such as buckets, augers, and hydraulic breakers, allowing it to tackle a multitude of tasks beyond traditional excavation. The quick coupler system enables easy switching between attachments, significantly reducing downtime during operations.

Overall, the Clarke L26 can be described as a well-rounded mini excavator that combines power, efficiency, and versatility. Its design is aimed at meeting the demands of modern construction and landscaping projects, making it a valuable asset for contractors and operators alike. Whether it's for digging trenches, landscaping gardens, or performing utility work, the L26 proves to be a competent machine that delivers reliable performance.
Top Page Image Contents