Clarke L26 manual Procedures For Transpoting

Page 7

Procedures For Transpoting (cont.)

11.Fasten the machine to the vehicle. Clarke Technology recommends a strap over the top of the machine and a strap to keep the machine from rolling forward or backwards. If this is not done, there is a possibility of the machine toppling over. Four tie down points (2 along each side of frame) are provided on machine for securing machine.

How to Remove the Machine From a Van or

Truck

1.Make sure there are no obstructions in the area.

2.Make sure the unloading ramp is at least eight

 

(8) feet (2.5m) long and a minimum of 32"

Figure #2

 

(0.8m) wide, and strong enough to support the

 

 

machine.

 

3.

Make sure the ramp is clean and dry.

 

4.

Put the ramp in position.

 

5.

Unfasten the machine.

 

WARNING: The machine is heavy. Make sure you use two able persons to assist in moving the machine down the ramp.

6.Turn the key switch "ON".

7.Set the traverse center knob to the slowest forward speed setting. Carefully and slowly, drive the machine to the top of the ramp and start down.

8.While pushing in the right or left forward/ reverse switch the machine will go forward. See figure 2.

9.As the machine begins to travel down the ramp, push in the forward/reverse switch to maintain a slow downward speed.

10.Replace squeegee assembly, brush housing, and brush or pad driver after machine is unloaded and ready to use.

CLARKE TECHNOLOGY Operator's Manual - Encore L26 Cylindrical

Page -7-

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Read this Book ManualTable of Contents Severe bodily injury or death. Read and observe all Danger Avertissement AdvertenciaClarke Technology Operators Manual -Encore L26 Cylindrical Introduction & Machine Specifications Introduction & Machine SpecificationsFigure #1 Procedures For TransportingProcedures For Transpoting Symbols Used on Encore L26 Cylindrical Symbols Used on Encore L26 Cylindrical Machine Control Panel Key Switch See , Item aHour Meter Not Illustrated Option Parking Brake Optional, See Figure Machine Controls and FeaturesHow To Install The Batteries How To Prepare the Machine For OperationBattery Maintenance How To Charge The Batteries How To Change or Rotate Brushes How To Operate The Squeegee How To Operate The MachineHow To Fill The Solution Tank Operating The Machine How To Clean a FloorHow To Clean a Very Dirty Floor These Maintenance Procedures Must Be Done Every Day MaintenanceDo These Procedures When You Begin Your Work Period Do These Procedures When You End Your Work MaintenanceDistilled Water only Maintenance Procedures To Be Done Every WeekMaintenance For The Squeegee How to Center or Offset the Brush Head How To Adjust The SqueegeeAdjusting Squeegee Tilt Adjusting Squeegee BladesHow to Level the Cylindrical Brush Head Brushes Size Description Used For Clarke Technology Encore L26 Cylindrical Accessories 3/02Squeegee Blades Description Assembly DescriptionClarke Technology Operators Manual -Encore L26 Cylindrical Encore There is no solution flow HOW to Correct Problems in the Machine Cause ActionProblem Cause Action Page Alto Product Support Branches Highway Springdale, Arkansas Clarke Technology Limited U.S. WarrantyBattery Warranty Always use genuine ClarkeTechnology Parts for repair

L26 specifications

The Clarke L26 stands as a notable entry in the realm of compact excavators, reflecting advanced engineering and user-centric design. This machine is designed for a variety of applications, including landscaping, utility work, and smaller construction projects.

One of the main features of the Clarke L26 is its compact size, which allows it to maneuver easily through tight spaces and urban environments. This machine has an overall width of approximately 2.6 meters, making it suitable for projects that require a mini excavator that can fit through narrow gaps and access constrained job sites.

Powered by a robust and efficient diesel engine, the L26 delivers optimal performance without compromising on fuel efficiency. The engine is designed to meet stringent emissions standards while providing ample torque for digging and lifting tasks. The hydraulic system of the L26 is another standout characteristic, featuring sophisticated components that ensure smooth operation and responsiveness during various digging and lifting operations.

The L26 also incorporates advanced technology that enhances operator comfort and productivity. Its spacious cab features ergonomic controls, providing operators with a user-friendly interface. The visibility from the cab is optimized to reduce blind spots, enabling the operator to work safely and efficiently. Additionally, the climate control system in the cab ensures a comfortable working environment, regardless of external weather conditions.

Safety features are paramount in the design of the Clarke L26. It comes equipped with a rollover protective structure (ROPS) and a falling-object protective structure (FOPS), which provide peace of mind to operators working in hazardous conditions. The machine's low center of gravity enhances stability, especially when working on uneven terrain.

In terms of versatility, the Clarke L26 can be outfitted with various attachments such as buckets, augers, and hydraulic breakers, allowing it to tackle a multitude of tasks beyond traditional excavation. The quick coupler system enables easy switching between attachments, significantly reducing downtime during operations.

Overall, the Clarke L26 can be described as a well-rounded mini excavator that combines power, efficiency, and versatility. Its design is aimed at meeting the demands of modern construction and landscaping projects, making it a valuable asset for contractors and operators alike. Whether it's for digging trenches, landscaping gardens, or performing utility work, the L26 proves to be a competent machine that delivers reliable performance.
Top Page Image Contents