Harman-Kardon AVR 247 owner manual Remote Control Function List Reference

Page 65

APPENDIX

1

 

2

3

4

5

6

7

8

9

10

11

12

13

14

 

15

16

17

18

19

20

21

22

23 24

25

26 27 28

29

30 31

32 33 34 35

36 37 38 39

40 41 42 43

44 45 46 47

48 49 50 51

52 53 54 55

56 57 58

59 60 61

62 63 64

65 66 67

68 69 70

Refer to the numbered buttons in Figure 92 when using the Function List.

Figure 92 – Remote Control Function List Reference

65

Page 64 Page 66
Image 65
Page 64 Page 66
Contents AVR Outdoor Antenna Grounding. If an outside antenna Safety InformationImportant Safety Information Staple Invoice Here Table of Contents Thank you for choosing Harman Kardon IntroductionAudio Section Surround ModesAudio Inputs Supplied AccessoriesAudio/Video Inputs With S-Video Digital Audio InputsFRONT-PANEL Controls Main Power Navigation Adjust Input IndicatorsCoaxial Video Switch Select Audio InputsVideo 1, Video 2, Video 3 and DVD Audio/Video Inputs REAR-PANEL ConnectionsREAR-PANEL Connections DVD A/V Bridge/DMP Controls an iPod docked in The Bridge Remote Control FunctionsChannel Input Selector Press this button to select Track Skip Transport Controls DSP Surround On-Screen DisplayRemote Control Functions Surround Modes Introduction to Home TheaterTypical Home Theater System Multichannel AudioConnections Connecting Source Devices to the AVRTypes of Connections Speaker ConnectionsDigital Audio Audio ConnectionsAnalog Video Video ConnectionsDigital Video RS-232 Serial Port FM antenna uses a 75-ohm F-connector. See FigureAntennas Placement of Surround Speakers in a 5.1-Channel System Speaker PlacementFront Speaker Placement Placement of Surround Speakers in a 7.1-Channel SystemSubwoofer Placement Step One Connect the Speakers InstallationStep Two Connect the Subwoofer Step Three Connect the AntennasAudio Connections Video Connections Recommended Source Component ConnectionsTiVo or other Or Video 1 Composite Video Input Video Video 2 Analog InputsVideo 3 Source Video 1 SourceVideo 2 Source Video 4 SourceNo video connections are needed Hdmi 1Tape Step Five Connect the Video Display Step Six Plug in AC PowerTurn on your source device Step Seven Insert Batteries in RemoteVideo Cable, Satellite Step Ten Install a Multiroom System OptionalEnter a code from , above Two steps are required the first time you turn on the AVR Press the Standby/On Switch on the front panel. See FigureStep Eleven Turn On the AVR Using the On-Screen Menu System Initial SetupEzSet/EQ Screen Configure the AVR 247 Using EzSet/EQTerminals What EzSet/EQ DoesEzSet/EQ Equalization Configure SourcesOnly upper case letters are available for titles Source Input Default Video InputSource Input CoaxYou are now ready to begin enjoying your new receiver Volume Control Sleep TimerOperation Turning On the AVRSource Selection HeadphonesTone Controls Channel Direct Inputs Audio Input SelectionVideo Input Selection We recommend that you connect this player as follows Using the TunerXM Radio Operation To store a station in one of the 30 presets see FigureUse the Numeric Keys to enter the desired preset number Recording Using TheBridgeTMTo store a channel in one of the 40 preset locations IPod Function Selecting a Surround Mode Digital Audio Signals Analog Audio SignalsAdvanced Functions Audio Processing and Surround SoundRepeated Surround Setup Menu Screen Night Mode Default ModesDolby Surround Settings Panorama adjusts wraparound surround effect Dolby Pro Logic Mode Group0 or Dolby Digital EX played asMode Group Enveloping sound field is desired Surround Mode Description Incoming Bitstream or SignalDolby Digital 2/0/.0 or ReferenceAppropriate when a subwoofer is used Mode GroupDTS Neo6 DTS 2/2/.0 or .1, 3/2/.0 orStep Three Manual Setup Menu Manual SetupStep One Determine Speaker Size Step Two Measure Speaker DistancesSpeaker Size Menu Large settingMove the cursor to the left to select the next submenu Delay Adjust MenuSpeaker Crossover Menu Using the Remote Control With the Test Tone Step Four Setting Channel Output Levels ManuallyHowever, if you prefer to make these adjustments manually, Make sure all speakers have been connected correctlyUsing the Full-OSD Menu Video AdjustmentsUsing the Front-Panel or Remote-Control Channel Command Multiroom Operation Installing a Multiroom SystemOperating the Multiroom System System SettingsDim Function Advanced Remote Control FunctionsPunch-Through Programming To dim the displayProcessor Reset Resetting the RemoteMacros MemoryTroubleshooting Guide DTS AVR 247 Technical SpecificationsTable A1 Source Input Setting Defaults Appendix Default settings, worksheets, remote product codesTable A2 Speaker/Channel Setting Defaults Table A3 Delay Setting DefaultsTable A5 Speaker/Channel Settings Table A4 Source Input SettingsAuto Poll Surround Mode Tone Mode Bass Treble Video Mode Title Video Input Audio InputTable A7 System Settings Table A6 Remote Control CodesTape Cassette VCR, PVR, DVD, Cable, SatelliteRemote Control Function List Reference Table A8 Remote Control Function ListFAV Table A8Aiwa Table A9 Table A10 Remote Control Product Codes VCR Table A11 Remote Control Product Codes CD Table A12 Remote Control Product Codes DVD Table A13 Remote Control Product Codes SATTable A15 Remote Control Product Codes CBL Table A16 Remote Control Product CodesPage
Top Page Image Contents