Harman-Kardon AVR 235 owner manual Stereo-Digital Mode, Delay Settings, To call up the menu

Page 22

System Configuration

The factory default setting is to have the sub- woofer turned off for this mode, but you may change that setting by following these steps:

1. Press the Speaker Button 6

.

2.Press the Set Button F@to activate the configuration menu.

3.Press the /¤ Buttons Don the remote or the /Buttons 7on the front panel to select the desired option. SUB NONE turns off the feed to the subwoofer, while SUB <L+R> turns it on.

4.When the desired setting has been entered, press the Set Button F@to return to nor- mal operation.

Stereo-Digital Mode

When the Stereo-Direct (Bypass) mode is in use a full range signal is always sent to the front left/right speakers. By its nature, that option does not pass the signal through the AVR’s digi- tal signal processing, creating the requirement for full-range speakers. If your front speakers are bandwidth limited, “satellite”speakers, we rec- ommend that you do NOT use the Bypass mode, but rather use the DSP SURROUND OFF mode for stereo listening.

To listen to programs in the two-channel stereo mode while taking advantage of the bass man- agement system, press the Stereo Mode

Selector until SURROUND OFF appears in the Main Information Display ˜ and the DSP and SURR. OFF Surround Mode Indicators (both light up. When only the SURR. OFF Surround Mode

Indicators (is lit you are in the Stereo-Direct (Bypass) mode.

When this mode is in use, the front left/right speakers and subwoofer may be configured to meet the requirements of your specific speakers using the steps shown in the Speaker Setup sec- tion on page 17.

Delay Settings

Due the different distances between the listen- ing position for the front channel speakers and the surround speakers, the amount of time it takes for sound to reach your ears from the front or surround speakers is different. You may com- pensate for this difference through the use of the delay settings to adjust the timing for the specific speaker placement and acoustic condi- tions in your listening room or home theater.

To re-synchronize the front, center and surround channels at first measure and note the distance from the listening/viewing position to the front, center, surround and surround back (if any) speakers in meters.

22SYSTEM CONFIGURATION

In addition to adjusting the delay time for each individual speaker position, the AVR is among the few A/V receivers that allows you to adjust the delay for the combined output of all speak- ers as a group. This feature is called A/V Sync Delay; it allows you to compensate for delays to the video image that may be caused by the pro- cessing in products such as digital video dis- plays, video scalers, digital cable or satellite sys- tems, or personal video recorders. With proper adjustment of the setting for A/V Sync Delay, you can eliminate the loss of lip sync that may be caused by digital video applications.

The Delay setting for all speakers configured for your system will be available only (with 5.1 or with 6.1/7.1 configuration) when any Dolby sur- round mode is selected (except Dolby-3-Stereo). In addition they are selectable with these modes only, with all other modes the delay times are fixed.

Note that the Delay settings are "Global" for all inputs, using those Dolby modes, and need not to be repeated with any input.

To start with the delay settings at first select any input associated with such a Dolby mode. Next, continue within the MASTER MENU (Figure 1). If the system is not already at that point, press the OSD button Lto bring up the mas- ter menu. Press the ¤ Button Dthree times or until the on-screencursor is pointing at the DELAYADJUST line. Press the Set Button

Fto call up the menu.

*

D E L A Y

A D J U S T *

F L

: 1 2 f t

S B R : 1 0 f t

C E N : 1 2 f t

S B L : 1 0 f t

F R

: 1 2 f t

S L : 1 0 f t

S R

: 1 0 F t

S U B : 1 0 f t

U N I T :

F E E T

M E T E R

A / V S Y N C

D E L A Y : 0 m S

B A C K T O M A S T E R M E N U

Figure 8

Next move the cursor to the UNIT line and select the unit for distances you prefer to enter, feet or meter. Then move the cursor to the FL line where the first adjustment is made. Now press the / Buttons E until the distance from the front left speaker to the pre- ferred listening position is entered. Next press the ¤ Button Donce to move to the next line.

Now the cursor will be at the CEN line so that the delay for the center speaker may be set. Press the / Buttons E until the dis- tance from the main listening position to the center speaker is entered. Repeat the procedure for all active speaker positions by pressing the

¤Button Dagain and use the / Buttons E to change the setting. Remember that this last adjustment will only be needed when you have surround back speakers

installed and Dolby Digital chosen as the sur- round mode.

When the delay time for all speaker positions has been set you may return to the master menu by pressing the /¤ Navigation Button D until the cursor is pointing to BACK TO MASTER MENU and then pressing the Set Button F. However, if you have a digital video source or a digital video display that caus- es lack of lip sync you may use the A/V Sync adjust feature to delay the audio signal as it is sent to all channels (as opposed to the individ- ual settings) so that the picture and sound are brought back together. We recommend that this adjustment be made using the direct access con- trols on the remote, as shown below. That enables you to see the image while making the adjustment; however, you may also adjust it here using the menu system.

To adjust the A/V Sync delay, press the /¤ Navigation Button Dso that the cursor is pointing to the A/V Sync Delay line on the menu and then press the / Navigation Button E to delay the sound sufficiently so that it matches the on-screen video.

The delay settings may be adjusted at any time using the remote control and while viewing an on-screen image by pressing the Delay Select

Button . The A/V Sync Delay setting is first, and it may be adjusted by pressing the Set Button Fwithin five seconds of when the A/V SYNC DELAY message appears in the on-screen display and the Lower Display Line ˜. Then, press the / Navigation Button E to enter the desired delay set- ting that brings the video and sound back in sync. Press the Set Button Fagain to enter the setting.

Note that the A/V Sync delay setting is unique to each video input source, so you may enter a dif- ferent setting to compensate for the differences between any product attached to the Video 1, 2, 3 or 4 inputs.

To change one of the individual speaker posi- tions directly, press the Delay Select Button

,followed by the /¤ Navigation Button Dto select the desired position as that name appears in the on-screen display and the Lower Display Line ˜. When the name of the speaker position to be adjusted appears press the Set Button Fwithin five seconds.

Press the / Navigation Button E to

enter the desired delay setting for that speaker and then press the Set Button Fto enter the setting. The /¤ Navigation Button D may be used to select another position, or you may simply wait five seconds for the system to time out and return to normal operation.

Image 22
Contents AVR 235 Audio/Video Receiver Table of Contents Declaration of ConformityIntroduction Description and FeaturesFront panel analog A/V inputs Important Safety Information Safety InformationUnpacking Front Panel Controls Digital Input Selector When playing a # Preset Stations Selector Press thisInformation on digital audio Rear Panel Connections Digital Audio Outputs Connect theseUnswitched Outlet + and negative terminalsMain Remote Control Functions › Button Speaker Select MuteChannel/8 Channel Direct Input See page 31 for more informationMain Remote Control Functions Output jacks Installation and ConnectionsAudio Equipment Connections Channel Direct Inputs External Amplifier ConnectionsVideo Equipment Connections Scart A/V ConnectionsAC Power Connections System and Power ConnectionsMain Room Remote Control Extension WattsSpeaker Placement Speaker SelectionSystem Setup System ConfigurationUsing the On-Screen Display First Turn OnSpeaker Setup Input SetupSet Button Fto bring up the Speaker Setup menu Figure Subwoofer Within five seconds, either press the ‹/› buttons Night Mode Settings Surround SetupSetting to your taste ¤ Button Dso that the cursor is next toConfiguring the Surround Off Stereo Modes Stereo-Direct Bypass ModeInstalled and Dolby Digital chosen as the sur- round mode Stereo-Digital ModeDelay Settings To call up the menuUsing EzSet Output Level AdjustmentPress and hold the SPL Indicator Select When all channels have the same output level Volume until you can hear the test noise clearlyIs then pressed to select OFF in the highlighted video System Configuration Operation Surround Mode ChartChannel Direct Inputs DTS Neo6 Music No delay availableMix of the in-phase material of the left and right channels Two-channel stereo program is being playedSource Selection Basic OperationChannel/8-Channel Direct Input Volume Up/Down buttons Surround Mode SelectionButton Dolby Digital Digital Bitstream IndicatorsDigital Audio Playback PCM Audio PlaybackAudio, while the main feature is available Surround Mode TypesSpeaker/Channel Indicators PCM Playback IndicationsOutput Level Adjustment With Source Signals Tape RecordingIndicator Select Operation Advanced FeaturesMemory Backup Front-Panel-Display FadeFull-OSD Time Out Adjustment Turn On Volume LevelSemi-OSD Settings Display BrightnessTuner Operation Default Surround ModeBasic Tuner Operation RDS Display Options RDS TuningRDS Operation Program Search PTYProgramming the Remote with Codes Programming the RemoteCode Readout Macro Programming Volume Punch-ThroughProgrammed Device Functions Channel Control Punch-Through Resetting the Remote MemoryBy the AVR Input Selector Function List SPLAVR DVD Power Switch 1 is pushed Troubleshooting GuideProcessor Reset Remote sensor ¯ is obscuredTechnical Specifications Harman Consumer Group International

AVR 235 specifications

The Harman-Kardon AVR 235 is a high-performance AV receiver that exemplifies the brand's commitment to delivering high-fidelity sound and cutting-edge technology. Designed for home theater enthusiasts, it combines a sleek aesthetic with powerful audio performance, making it an appealing choice for those looking to elevate their cinematic experience.

One of the standout features of the AVR 235 is its 7.1-channel surround sound capability, allowing for a truly immersive audio experience. It can deliver up to 70 watts per channel, ensuring that every sound, from the softest whisper to the loudest explosion, is reproduced with clarity and power. The receiver supports various surround sound formats, including Dolby Digital, Dolby Pro Logic II, and DTS, providing users with a versatile listening experience tailored to any content.

The AVR 235 integrates several advanced technologies to improve sound quality. This includes Harman-Kardon's proprietary "Logic 7" technology, which enhances stereo sources to provide a more expansive surround sound experience. Its advanced DSP (Digital Signal Processing) algorithms further optimize the audio signals, ensuring that the sound is not only powerful but also richly detailed and accurate.

Connectivity options abound with the AVR 235, facilitating a range of devices to be hooked up effortlessly. It features multiple HDMI inputs, component and composite video inputs, as well as analog and digital audio inputs. This extensive range of connections allows for seamless integration with Blu-ray players, gaming consoles, streaming devices, and more, making it a versatile hub for home entertainment.

The AVR 235 also places a strong emphasis on user-friendliness, boasting an intuitive on-screen display and a user-friendly remote control. The graphical user interface guides users through the setup process and offers various adjustments to accommodate different room acoustics and personal preferences.

Additionally, the AVR 235 supports multi-room audio configurations, enabling users to enjoy sound throughout the house. It features an integrated AM/FM tuner, allowing access to radio stations, and provides options for connecting to external audio sources.

In summary, the Harman-Kardon AVR 235 is a powerful and feature-rich AV receiver that delivers exceptional sound quality and versatility. Its advanced technologies, extensive connectivity options, and user-friendly design make it an excellent choice for anyone looking to enhance their home theater system and enjoy a superior audio experience. With the AVR 235, Harman-Kardon once again proves its prowess in the world of high-fidelity audio.