Delta DVP-ES2/EX2/SS2/SA2/SX2/SE manual M1274 C239 counting mode on falling-edge

2. Programming Concepts

Special		ES2	SS2	SA2	SX2	OFF	STOP	RUN	Attrib.	Latch	Default
	Function					Ø	Ø	Ø
M		EX2				ON	RUN	STOP		-ed
M1274	C239 counting mode (ON: falling-edge	○	○	○	○	OFF	-	-	R/W	NO	OFF
	count)
M1275	C240 counting mode (ON: falling-edge	○	○	○	○	OFF	-	-	R/W	NO	OFF
	count)
M1276	C241 counting mode (ON: falling-edge	○	○	○	○	OFF	-	-	R/W	NO	OFF
	count)
M1277	C242 counting mode (ON: falling-edge	○	○	○	○	OFF	-	-	R/W	NO	OFF
	count)
M1280*	For I000 / I001, reverse interrupt trigger	○	○	○	○	OFF	OFF	-	R/W	NO	OFF
	pulse direction (Rising/Falling)
M1284*	For I400 / I401, reverse interrupt trigger	○	○	○	○	OFF	OFF	-	R/W	NO	OFF
	pulse direction (Rising/Falling)
M1286*	For I600 / I601, reverse interrupt trigger	○	○	○	○	OFF	OFF	-	R/W	NO	OFF
	pulse direction (Rising/Falling)
M1303	High / low bits exchange for XCH	○	○	○	○	OFF	-	-	R/W	NO	OFF
	instruction
M1304*	Enable force-ON/OFF of input point X	○	○	○	○	OFF	-	-	R/W	NO	OFF
M1305	Reverse Y1 pulse output direction in high	○	○	○	○	OFF	OFF	-	R/W	NO	OFF
	speed pulse output instructions
M1306	Reverse Y3 pulse output direction in high	○	○	○	○	OFF	OFF	-	R/W	NO	OFF
	speed pulse output instructions
M1307	For ZRN instruction, enable left limit	○	○	○	○	OFF	OFF	-	R/W	NO	OFF
	switch
M1308*	Output specified pulses or seek Z phase	○	○	○	○	OFF	OFF	OFF	R/W	NO	OFF
	signal when zero point is achieved.
	For COM1(RS-232), sending request
M1312	(Only applicable for MODRW and RS	○	○	○	○	OFF	OFF	-	R/W	NO	OFF
	instruction)
	For COM1(RS-232), ready for data
M1313	receiving (Only applicable for MODRW	○	○	○	○	OFF	OFF	-	R/W	NO	OFF
	and RS instruction)
	For COM1(RS-232), data receiving
M1314	completed (Only applicable for MODRW	○	○	○	○	OFF	OFF	-	R/W	NO	OFF
	and RS instruction)
	For COM1(RS-232), data receiving error
M1315	(Only applicable for MODRW and RS	○	○	○	○	OFF	OFF	-	R/W	NO	OFF
	instruction)
	For COM3(RS-485), sending request
M1316	(Only applicable for MODRW and RS	○	╳	○	╳	OFF	OFF	-	R/W	NO	OFF
	instruction)
	For COM3(RS-485), ready for data
M1317	receiving (Only applicable for MODRW	○	╳	○	╳	OFF	OFF	-	R/W	NO	OFF
	and RS instruction)
	For COM3(RS-485), data receiving
M1318	completed (Only applicable for MODRW	○	╳	○	╳	OFF	OFF	-	R/W	NO	OFF
	and RS instruction)
	For COM3(RS-485), data receiving error
M1319	(Only applicable for MODRW and RS	○	╳	○	╳	OFF	OFF	-	R/W	NO	OFF
	instruction)
M1320*	For COM3 (RS-485), ASCII/RTU mode	○	╳	○	╳	OFF	-	-	R/W	NO	OFF
	selection. (OFF: ASCII; ON: RTU)

2 - 2 5