Delta DVP-ES2/EX2/SS2/SA2/SX2/SE manual Yes ’Ffff

2. Programming Concepts

Special	Content	ES2	SS	SA	SX	OFF	STOP	RUN	Attrib.	Latch	Default
D		EX2	2	2	2	Ø	Ø	Ø		-ed
						ON	RUN	STOP
	Feedback data (ASCII) of Modbus
D1070	communication. When PLC’s RS-485
↓	communication instruction receives feedback	○	○	○	○	0	-	-	R	NO	0
	signals, the data will be saved in the registers
D1085
	D1070~D1085. Usres can check the received
	data in these registers.
D1086	High word of the password in DVP-PCC01	○	○	○	○	0	-	-	R/W	NO	0
	(displayed in hex according to its ASCII codes)
D1087	Low word of the password in DVP-PCC01	○	○	○	○	0	-	-	R/W	NO	0
	(displayed in hex according to its ASCII codes)
	Sent data of Modbus communication.
D1089	When PLC’s RS-485 communication instruction	○	○	○	○	0	-	-	R	NO	0
↓	sends out data, the data will be stored in
D1099	D1089~D1099. Users can check the sent data in
	these registers.
D1109*	COM3 (RS-485) Communication protocol	○	╳	○	○	H’86	-	-	R/W	NO	H’86
D1110*	Average value of EX2/SX2 analog input channel 0					0	-	-	R	NO	0
	(AD 0) When average times in D1062 is set to 1,	○	╳	╳	○
	D1110 indicates present value.
D1111*	Average value of EX2/SX2 analog input channel 1					0	-	-	R	NO	0
	(AD 1) When average times in D1062 is set to 1,	○	╳	╳	○
	D1111 indicates present value
D1112*	Average value of EX2/SX2 analog input channel 2					0	-	-	R	NO	0
	(AD 2) Whenaverage times in D1062 is set to 1,	○	╳	╳	○
	D1112 indicates present value
	Average value of 20EX2/SX2 analog input					0	-	-	R	NO	0
	channel 3 (AD 3) Whenaverage times in D1062 is	○	╳	╳	○
D1113*	set to 1, D1113 indicates present value
	Displaying the status of the analog input channel	○	╳	╳	╳	0	-	-	R	NO	0
	of 30EX2
	Enable/disable 20EX2/SX2 AD channels
D1114*	(0: enable (default) / 1: disable)	○	╳	╳	○	0	-	-	R/W	YES	0
	bit0~bit3 sets AD0~AD3.
	P.S. 30EX2 does not support this function.
D1115*	20EX2/SX2 analog input/output mode setting	○	╳	╳	○	0	0	0	R/W	YES	0
	30EX2 analog input/output mode setting	○	╳	╳	╳	-	-	-	R/W	YES	H’FFFF
D1116*	Output value of analog output channel 0 (DA 0) of	○	╳	╳	○	0	0	0	R/W	NO	0
	EX2/SX2
	Output value of analog output channel 1 (DA 0) of
D1117*	20EX2/SX2	○	╳	╳	○	0	0	0	R/W	NO	0
	P.S. 30EX2 does not support this function.
D1118*	EX2/SX2 sampling time of analog/digital					2	-	-	R/W	YES	2
	converstion. Default: 2. Unit: 1ms. Sampling time	○	╳	╳	○
	will be regarded as 2ms if D1118≦2
D1120*	COM2 (RS-485) communication protocol	○	○	○	○	H’86	-	-	R/W	NO	H’86
D1121*	COM1(RS-232) and COM2(RS-485) PLC	○	○	○	○	-	-	-	R/W	Yes	1
	communication address
D1122	COM2(RS-485) Residual number of words of	○	○	○	○	0	0	-	R	NO	0
	transmitting data
D1123	COM2(RS-485) Residual number of words of the	○	○	○	○	0	0	-	R	NO	0
	receiving data

2 - 4 1