Delta DVP-ES2/EX2/SS2/SA2/SX2/SE manual M1233 C233 counter monitor on count down

DVP - ES2/EX2/SS2/SA2/SX2/SE Operation Manual - Programming

Special		ES2	SS2	SA2	SX2	OFF	STOP	RUN	Attrib.	Latch	Default
	Function					Ø	Ø	Ø
M		EX2				ON	RUN	STOP		-ed
M1233	C233 counter monitor (ON: count down)	○	○	○	○	OFF	-	-	R	NO	OFF
M1234	C234 counter monitor (ON: count down)	○	○	○	○	OFF	-	-	R	NO	OFF
M1235	C235 counting mode (ON: count down)	○	○	○	○	OFF	-	-	R/W	NO	OFF
M1236	C236 counting mode (ON: count down)	○	○	○	○	OFF	-	-	R/W	NO	OFF
M1237	C237 counting mode (ON: count down)	○	○	○	○	OFF	-	-	R/W	NO	OFF
M1238	C238 counting mode (ON: count down)	○	○	○	○	OFF	-	-	R/W	NO	OFF
M1239	C239 counting mode (ON: count down)	○	○	○	○	OFF	-	-	R/W	NO	OFF
M1240	C240 counting mode (ON: count down)	○	○	○	○	OFF	-	-	R/W	NO	OFF
M1241	C241 counting mode (ON: count down)	○	○	○	○	OFF	-	-	R/W	NO	OFF
M1242	C242 counting mode (ON: count down)	○	○	○	○	OFF	-	-	R/W	NO	OFF
M1243	C243 Reset function control. ON = R	○	○	○	○	OFF	-	-	R/W	NO	OFF
	function disabled
M1244	C244 Reset function control. ON = R	○	○	○	○	OFF	-	-	R/W	NO	OFF
	function disabled
M1245	C245 counter monitor (ON: count down)	○	○	○	○	OFF	-	-	R	NO	OFF
M1246	C246 counter monitor (ON: count down)	○	○	○	○	OFF	-	-	R	NO	OFF
M1247	C247 counter monitor (ON: count down)	○	○	○	○	OFF	-	-	R	NO	OFF
M1248	C248 counter monitor (ON: count down)	○	○	○	○	OFF	-	-	R	NO	OFF
M1249	C249 counter monitor (ON: count down)	○	○	○	○	OFF	-	-	R	NO	OFF
M1250	C250 counter monitor (ON: count down)	○	○	○	○	OFF	-	-	R	NO	OFF
M1251	C251 counter monitor (ON: count down)	○	○	○	○	OFF	-	-	R	NO	OFF
M1252	C252 counter monitor (ON: count down)	○	○	○	○	OFF	-	-	R	NO	OFF
M1253	C253 counter monitor (ON: count down)	○	○	○	○	OFF	-	-	R	NO	OFF
M1254	C254 counter monitor (ON: count down)	○	○	○	○	OFF	-	-	R	NO	OFF
M1257	Set the ramp up/down of Y0, Y2 to be “S	○	○	○	○	OFF	OFF	-	R/W	NO	OFF
	curve.” ON = S curve.
M1260	Set up X7 as the reset signal for software	○	○	○	○	OFF	-	-	R/W	NO	OFF
	counters C235 ~ C241
	Enable cyclic output for table output
M1262	function of DPTPO instruction. ON =	○	○	○	○	OFF	OFF	-	R/W	NO	OFF
	enable.
M1270	C235 counting mode (ON: falling-edge	○	○	○	○	OFF	-	-	R/W	NO	OFF
	count)
M1271	C236 counting mode ON: falling-edge	○	○	○	○	OFF	-	-	R/W	NO	OFF
	count)
M1272	C237 counting mode (ON: falling-edge	○	○	○	○	OFF	-	-	R/W	NO	OFF
	count)
M1273	C238 counting mode (ON: falling-edge	○	○	○	○	OFF	-	-	R/W	NO	OFF
	count)

2 - 24