Delta DVP-ES2/EX2/SS2/SA2/SX2/SE manual D1031 PV of Y0 pulse output High word

DVP - ES2/EX2/SS2/SA2/SX2/SE Operation Manual - Programming

Special	Content	ES2	SS	SA	SX	OFF	STOP	RUN	Attrib.	Latch	Default
D		EX2	2	2	2	Ø	Ø	Ø		-ed
						ON	RUN	STOP
D1023*	Register for Storing detected pulse width (unit:	○	○	○	○	0	-	-	R/W	NO	0
	0.1ms)
D1025*	Code for communication request error	○	○	○	○	0	-	-	R	NO	0
D1026*	Pulse number for masking Y0 when M1156 = ON	○	○	○	○	0	0	-	R/W	NO	0
	(Low word)
D1027*	Pulse number for masking Y0 when M1156 = ON	○	○	○	○	0	0	-	R/W	NO	0
	(High word)
D1028	Index register E0	○	○	○	○	0	-	-	R/W	NO	0
D1029	Index register F0	○	○	○	○	0	-	-	R/W	NO	0
D1030	PV of Y0 pulse output (Low word)	○	○	○	○	-	-	-	R/W	YES	0
D1031	PV of Y0 pulse output (High word)	○	○	○	○	-	-	-	R/W	YES	0
D1032	PV of Y1 pulse output (Low word)	○	○	○	○	0	-	-	R/W	NO	0
D1033	PV of Y1 pulse output (High word)	○	○	○	○	0	-	-	R/W	NO	0
D1036*	COM1 (RS-232) communication protocol	○	○	○	○	H’86	-	-	R/W	NO	H’86
D1037*	Register for setting 8-sets SPD function (has to be	○	○	○	○	0	-	-	R/W	NO	0
	used with M1037)
	1. Delay time setting for data response when PLC
	is SLAVE in COM2 / COM3 RS-485
D1038	communication. Range: 0 ~ 10,000 (unit: 0.1ms).	○	○	○	○	-	-	-	R/W	NO	0
	2. By using PLC LINK in COM2 (RS-485), D1038
	can be set to send next communication data with
	delay. Range: 0 ~ 10,000 (Unit: one scan cycle)
D1039*	Fixed scan time (ms)	○	○	○	○	0	-	-	R/W	NO	0
D1040	No. of the 1st step point which is ON.	○	○	○	○	0	-	-	R	NO	0
D1041	No. of the 2nd step point which is ON	○	○	○	○	0	-	-	R	NO	0
D1042	No. of the 3rd step point which is ON.	○	○	○	○	0	-	-	R	NO	0
D1043	No. of the 4th step point which is ON	○	○	○	○	0	-	-	R	NO	0
D1044	No. of the 5th step point which is ON.	○	○	○	○	0	-	-	R	NO	0
D1045	No. of the 6th step point which is ON	○	○	○	○	0	-	-	R	NO	0
D1046	No. of the 7th step point which is ON.	○	○	○	○	0	-	-	R	NO	0
D1047	No. of the 8th step point which is ON	○	○	○	○	0	-	-	R	NO	0
D1049	No. of alarm which is ON	○	○	○	○	0	-	-	R	NO	0
D1050	Converted data for Modbus communication data
↓	processing. PLC automatically converts the ASCII	○	○	○	○	0	-	-	R	NO	0
	data in D1070~D1085 into Hex data and stores
D1055
	the 16-bit Hex data into D1050~D1055
	Average number of times an analog signal is input
D1062*	to the EX2/SX2 series PLC	○	╳	╳	○	2	-	-	R/W	YES	2
	The default value is K10 for EX2 version 2.6 and
	version 2.8.
D1067*	Error code for program execution error	○	○	○	○	0	0	-	R	NO	0
D1068*	Address of program execution error	○	○	○	○	0	-	-	R	NO	0

2 - 40