Delta DVP-ES2/EX2/SS2/SA2/SX2/SE manual D1240 stores the low word of high-speed counter

2. Programming Concepts

Special	Content	ES2	SS	SA	SX	OFF	STOP	RUN	Attrib.	Latch	Default
D		EX2	2	2	2	Ø	Ø	Ø		-ed
						ON	RUN	STOP
D1187	Index register F3	○	○	○	○	0	-	-	R/W	NO	0
D1188	Index register E4	○	○	○	○	0	-	-	R/W	NO	0
D1189	Index register F4	○	○	○	○	0	-	-	R/W	NO	0
D1190	Index register E5	○	○	○	○	0	-	-	R/W	NO	0
D1191	Index register F5	○	○	○	○	0	-	-	R/W	NO	0
D1192	Index register E6	○	○	○	○	0	-	-	R/W	NO	0
D1193	Index register F6	○	○	○	○	0	-	-	R/W	NO	0
D1194	Index register E7	○	○	○	○	0	-	-	R/W	NO	0
D1195	Index register F7	○	○	○	○	0	-	-	R/W	NO	0
D1220	Pulse output mode setting of CH0 (Y0, Y1)	○	○	○	○	0	-	-	R/W	NO	0
D1221	Pulse output mode setting of CH1 (Y2, Y3)	○	○	○	○	0	-	-	R/W	NO	0
D1232*	Number of output pulses for CH0 (Y0, Y1) ramp-					0	0	--	R/W	NO	0
	down stop when mark sensor receives signals.	○	○	○	○
	(Low word).
D1233*	Number of output pulses for CH0 (Y0, Y1) ramp-					0	0	--	R/W	NO	0
	down stop when mark sensor receives signals.	○	○	○	○
	(High word).
D1234*	Number of output pulses for CH1 (Y2, Y3) ramp-					0	0	--	R/W	NO	0
	down stop when mark sensor receives signals.	○	○	○	○
	(Low word).
D1235*	Number of output pulses for CH2 (Y2, Y3) ramp-					0	0	--	R/W	NO	0
	down stop when mark sensor receives signals.	○	○	○	○
	(High word).
D1240*	When interupt I400/I401/I100/I101 occurs,	○	○	○	○	0	0	-	R	NO	0
	D1240 stores the low word of high-speed counter.
	When interupt I400/I401/I100/I101 occurs,
D1241*	D1241 stores the high Word of high-speed	○	○	○	○	0	0	-	R	NO	0
	counter.
D1242*	When interupt I500/I501/I300/I301 occurs,	○	○	○	○	0	0	-	R	NO	0
	D1242 stores the low Wordof high-speed counter.
D1243*	When interupt I500/I501/I300/I301 occurs, D1243	○	○	○	○	0	0	-	R	NO	0
	stores the high Word of high-speed counter.
D1244	Idle time (pulse number) setting of CH0 (Y0, Y1)	○	○	○	○	0	-	-	R/W	NO	0
	The function is disabled if set value≦0.
D1245	Idle time (pulse number) setting of CH1 (Y2, Y3)	○	○	○	○	0	-	-	R/W	NO	0
	The function is disabled if set value≦0.
	Set value for COM1 (RS-232) data receiving time-
D1249	out (Unit: 1ms, min. 50ms, value smaller than					0	-	-	R/W	NO	0
	50ms will be regarded as 50ms) (only applicable	○	○	○	○
	for MODRW/RS instruction) In RS instruction, no
	time-out setting if “0” is specified.
D1250	COM1 (RS-232) communication error code (only	○	○	○	○	0	-	-	R/W	NO	0
	applicable for MODRW/RS instruction)
	Set value for COM3 (RS-485) data receiving time-
D1252	out (Unit: 1ms, min. 50ms, value smaller than					50	-	-	R/W		50
	50ms will be regarded as 50ms) (only applicable	○	╳	○	╳					NO
	for MODRW/RS instruction) In RS instruction, no
	time-out setting if “0” is specified

2 - 4 3